Sundown Audio

I have two SA-15's and I just finished making my box with the intent of adding in 6" PSP ports when they arrived in the mail. I was pressed for time because I'm going back to school (nine hours away) tomorrow so that's why I finished everything except for adding the ports. Well I ordered the ports from parts-express last Monday and just to make sure they got to my house in time I paid for two day shipping. I MADE SURE they were in stock when I ordered them. Guess what happened? The ports didn't ship out until Thursday. I called parts-express on Thursday to see why I didn't have the ports yet and they told me that "they just shipped out today (Thursday) because the parts w…

I bought out all of the QC failed SI BM 10s (old models) and re-built them with several changes: 1) Slightly longer flat-wound coil (original was round wire) - USA made coils 2) Narrower / Taller Surround 3) Tied down tinsel leads Measured T/S Specs (coils in series): RE: 6.89 ohms Z: 8 ohms Fs: 27.2 Hz Qes: 0.56 Qms: 3.32 Qts: 0.48 Le: 2.8 mH Vas: 31.1 L BL: 16.2 NA Mms: 124 grams Power: 400 watts RMS 0.95 ft^3 SEALED BOX - F3 of 41 Hz 1.5 ft^3 ported tuned to 30 - 35 Hz for high output I have about 40 of these... $125 shipped in the continental USA for one $240 shipped in the continental USA for two $440 shipped in the continental USA for four Ask about more than th…

My order of SA-8's is on the way (should arrive today). This is my first experience with sundown products, and Im extremely excited to try out these 8's! I ordered 4, but decided to only put two in my car for now, ran off a RF 1000bd Amplifier. The other two Ill put in my truck later on another 1000bd I wanted to make a nice box for it, something that looks as good as it sounds. Most of my boxes are all about function, this one started that way, but has since changed into quite the nice box. The box is built to 1.1 ft^3 net, 1.5 gross volume, 18 inches of port area, and tuned to 34 hz. I should have the last few coats of clear applied today, and I should have the subs…

So I bought a SAZ-3000d from db-r last december. I finally got to hook it up today! It turned on, sub wouldn't move, then the amp would go into protect. The btl was wired at one Ohm. So after reading the manual, I disconnected the speaker wire and the amp did fine, didn't go into protect mode. So I re-did the wiring on the sub but before dragging it out to the car, I decided to test the amp. Turned it on and the Blue power light came on and about one second later it switched over to protect. Needless to say I was astonished. The wiring is done as so: From battery plug in of amp to 300amp ANL fuse, from fuse to + battery, from + battery to another 300 amp ANL fuse, from t…

Just to start things off, I haven't really done much research and I'm completely new to this forum, so I'm sure I'm repeating a previously stated question. Anyway, I'm new to the car audio game and I want to hit lower notes. I have a Sundown X12 on an Orion CB3200.1D. It's in a box that I can give you just about zero information on because I have no information on it. I had a local company just build me a decent box that would get the job done. I somewhat understand that bigger box = lower frequency, or something like that, but how can I hit lower notes without changing the box? Is there anything I can do with positioning of the box (I have a 2002 Ford Explorer, btw), …

I'm not telling

Sundown Team, I am looking at the forum about this but I can't seem to find any article discussion the difference between the two good sub aside from its RMS. Thanks

When is the estimated arrival date?

i would really like to see some nice 2 way and 3 way components that perform without being ripped off for them and have a brand i love backing them, what about you guys?

So... I want to do something for real this time and actually get a vehicle that can handle some weight and still drive around without issues. Concerns about driveability have really hampered my previous plans for something large. I really do NOT like driving huge vehicles either for the most part. I happened across a really interesting vehicle by chance on Craigslist last week and decided to pull the trigger ! 2006 Chevy Express 3500 w/ Duramax Diesel Engine! I test drove it and it was alot more comfortable for me to drive than most huge vehicles and has some real power behind it as well. I am looking at mostly music and mostly impressive demoing but would plan to compete…

topic says it all. i have a 3000 watt sundown, how mnay runs of 0 gauge should i make, i have one run now. ill run up to 3 runs of need be i have 3 yellow tops and 2 bl 15's

As of March 31st, 2007 the "Z" series amplifiers will no longer carry 0.5 ohm warranty coverage. You can read a more complete explanation as to why this came about here: http://www.soundsolutionsaudio.com/forum/i...?showtopic=7556 Old SAZ-1500D 1/2 ohm warranty coverage thread for amps sold before March 31st: http://www.soundsolutionsaudio.com/forum/i...?showtopic=7151

SA Series Coil Cooling Testing SA Series Coil Cooling Testing II -- SA-15 Thermal Test (with updated spacer / plug) SA-12 QC Test with Power Clamp Prototype SA-15 Excursion Test Video Sundown SA-8 Thermal Test SA-12 SQ Review -- They aren't JUST loud. 4x SA-12s : 149.9 Bass Racer 147.3 / One SA-12 Skip01: SA-12 and 2 2500s metering....legal and kick Loudest Pair of SA-12s that I know of 4x SA-10s = 154.9 dB 8 SA10's walled in Tonka's S10 6x SA-12s and 4x 1500Ds - 154.6 on music Russian Customer Sa-12 On Music / Db Meter 2 sa-10s on music - 148.8 Average 30 seconds USACI 2x SA-12s on 3000D "Jacob I'm Impressed" 1x SA-8 w/ SPL Coil : 151.6 dB Outlaw Jacob…

Below text compose by Mike Bruno for the sale of these drivers. We are not re-building them; Mike is. All after sales support will be handled by Mike by his terms on these refurbished drivers. PM: woofercooker – or preferably – e-mail: [email protected] for inquiries. ---------- I will be selling Sundown’s inventory of SA-8s that have either failed quality control testing or were returned by customers. Each of these woofers were tested by Jacob and found to have a defect in the coil alignment or other cosmetic / performance defects. I will be refurbishing these woofers with the latest OEM SA-8 parts and reselling them to the public. Many of these have never bee…

Just got my first pictures of the first completed prototype of the new SAZ-1500D v.3 model... so the cat is out of the bag on this one! As the model that got us started it is only appropriate that it is the first model to be shown in the 2012 trim! Newly tooled 2012 casing -- you can still tell it IS a Sundown amp but it is a refresher and also narrower. The FETs are mounted at a 45 degree angle to shrink the width AND avoid spring clips (which I've never liked). So we are getting the best of both worlds on that. * Fully custom tooled boards for all of our new 2012 models complete with fans. More photos to come as I get the other models done! Yes... you do see 16 power s…

$200 shipped in the continental USA on pre-order! Payment via Paypal to [email protected] Same crossovers as SAX-100.4C Revision: # Selectable HP / LP / FULL crossover # CH 1 & 2 Variable HP crossover 50 - 5000 Hz @ 12 dB # CH 1 & 2 Variable LP crossover 50 - 500 Hz @ 12 dB # CH 3 & 4 Variable HP crossover 50 - 500 Hz @ 12 dB # CH 3 & 4 Variable LP crossover 50 - 5000 Hz @ 12 dB # 10 Hz - 500 Hz variable subsonic filter (CH 1&2 and CH 3&4) # Subsonic filter allows for band-passed crossover configuration # 50W x 4CH @ 4 ohms # 80W x 4CH @ 2 ohms # 160W x 2CH @ 4 ohms 12" x 9" foot-print - just slightly longer than SAE-1000D!!! ----- Photos o…

I am going to make the official announcement now that we are sold out of new SAZ-2000Ds -- yes, I am in fact sold out... a few used ones remain but that is it. To replace it I am developing an SAZ-2500D model. This is a new board tooling for Sundown and is ours in the USA exclusively just like the SAZ-3500D. Just a HAIR larger than the SAZ-2000D and over 500 watts more power is expected from it. I am excited about it -- more details will be available once I have the prototype in hand. This evens out the amp line to 1500, 2500, 3500, and 4500 so there is not such a large gap from the 2000 to the 3500. It is too early for ETAs or pricing... but I will do a pre-order once te…

Just a heads up... I will be gone for about 5 days, January 5 - 10, for the CES show this year. Sundown Audio will be closed for that time... if it is an emergency I may be able to have someone ship an item during that time -- but normal orders will not go anywhere until I get back from CES.

Hey Guys, Just wondering, how do you know if you are clipping your amp? I thought it was if your voltage drops to low. If it does have something to do about voltage, where can you get the electronic volt meters I've seen in ppl's car?

So... the SA-8 is pretty badass... but I want something louder. Starting on this project : Yep... a Neo 8 with a 3" coil and 22mm linear one-way excursion (that is XBL^2 that you see) and x-mech of 27mm on the frame I'll be utilizing. Will handle around 1000-watts RMS without much trouble thermally and mechanically. Tooling new spiders and cones just for this driver. Going to see how it turns out... but simulation predicts motor force more than 300% higher than the SA-8 if all turns out according to plan. I am designing it for myself primarily as I want to do 157s with four 8s... but I think others will enjoy them too =) Pricing will be a bit higher than an NS v.2 due t…

Should a box 2.75 cubes tuned to 40 hz be alright for a single nightshade 12?

Okay since I'm so close to putting my new system together for the 2011 MWSPL season I have this question. My electrical will consist of a 180 amp DC Power Alternator, a CarQuest NGT Extreme 100 Ah AGM battery under the hood and a Deka 9A31 in the trunk, will this be enough to power a SAZ-3500D? I've heard yes and no. Of course I know to watch my voltage but I've had a few people tell me to get at least 2 batts for the trunk (if I had the space) it's going in the back of a 01 Camry.

We're working on a new build for the Excursion. 16 Sundown Audio sa-12s powered by 4 saz-3500s. Box sketch Close up of ports. Three 8" custom flared ports. Cutting the wood Laminating. The entire box will be at least two layers thick. Three & four layers in certain places. Starting the router work for the ports. I call this pic Cock & Balls. Lots more work to do. I barely got started on the port work. No where near done with that piece & I have two more identical pieces to build. Stay tuned...

The SAZ-3000Ds are completely out of stock now - no more available for trade-in program or for sale otherwise. If you need another one please contact dB-R as he has some refurbished units for sale.