Sundown Audio

... and SA-8 bolt down ring. Truck showed up late today * SA-8 and mystery prototype in background being tested. * Ohhh, nice looking magnet boot ! * Screws for bolt down ring * Just to make sure... the ring was also epoxied in. * SA-12 with magnet boot

I was planing to build a box that's about 1.50 cubic feet tuned to 36hz that's all I have room for. But I don't know which sub I should get Sa-12 Sa-10 E12v2. My amp should do around 750rms clean. This is for a ext cab truck. Any help would be greatly appreciated.

1) is 1 cu ft good after all displacements? I'll be over powering it alittle 2) how much port area? I'm tuning between 30-33 hz?

I Have two sa12's on saz-1200d in a ported box @38hz its a hammer to the chest loud .. only problem its lacking low end.. box is 4 cubes total.. I don't want to give up much of that ear drum pounding that it has now but pick up low end would going to 35hz be a good change.. an would the box size need to go up or down ?

How will 2 Sundown sa15 sound in a sealed enclosure around 4.5 cf

Can some help me with dimesion for an slot-ported enclosure, for one sa15.I have a 2004 Buick Regal.I'm planning running 750rms to this subwoofer. I need all cut pieces.The height has to be 16' OR LESS.

Originally posted by Greg Kashin : November 2010 ---------- So, Jacob was kind enough to let us have his SA15 test sample and it came in a few weeks ago... the guys at D Style Audio were a little busy but we got it up and running this weekend. the box went into Drugban's Ford Explorer it's just a bit under 4 cubes net and tuned to 37hz (they took it down a bit by blocking off a part of the port later on as you can see in the pics) amps are two of the new SAX1200D's bridged @2ohms (great little amps by the way) The Optima we had in the back was laying in the shop for quite some time and was reasting just over 12 volts...we saw quite a bit of voltage drop but still clmped …

Hey there! I have this awesome little subwoofer that i have barely used more than a few hours - and the surround in a small area is comming up from the landing. i heard chuffing in a sealed box with the grommet and thought there was an air leak. upon further inspection i came to notice that the surround was not fully adhered to the basket surround landing! this is a project for a customer of mine, and i have already sent an email into you via your web support contact form - but this is kind of an emergency, as i am supposed to be finishing the fiberglass box for him this weekend - i am about 50% done with it and i am going to push forward with the baffle and port still -…

ok, so i read the specs for the 1000d, and it says battery wire terminal, 0 guage, so i go on ebay and buy a 0 gauge amp kit. and then when i go to hook up my amp, the zero gauge wire is 1/3 to big, and i thought rockford fostage would be more accurate, maybe it was that , or maybe sundown made a mistake on my amp or somthing, i heard it was ok to take off wire to make it smaller, as long as you clean it up nice, and then electrical tape it, so that is how it stands now. my box isnt here yet. so i havnt ran it yet. all sugjestions are apreciated so much, this is my dream system and i dont want to fuk it up by jerry rigging it like that or somthing. thanks guys. kevin

I want to know what the damping factor is @1 ohm, 2ohm and 4ohm also wnat to know how many amps the amp takes from the electrical system at all ohms, should be ok on my stock alt 100amps

i have been looking at getting an 12" fi ssd and its rated at 800 rms. I have also been lookin at amps and everyone has something good to say about sundown. Would the sundown sae 1200d be a good choice for the 12" fi ssd? thanks

PRE-SALE ORDERS ARE FINAL - THERE WILL BE NO REFUNDS -- If you are not 100% sure you will be financially stable then don't pre-order. No more exceptions. These amps are capable of a real 1500+ watts at 12.8 volts. They will out-perform many other 1500 watt rated amps (like the Audiopipe 1500) easily! COST ON PRE-SALE : AUGUST - $250 each SEPTEMBER - $260 each OCTOBER - $270 each NOVEMBER - $280 each PRICE IS SHIPPED IN CONTINENTAL 48 STATES. CONTACT ME ABOUT AK, HI, and international !!! The earlier you pre-order the lower the price will be. REGULAR price will be $350 MAP / $549 MSRP when in stock! PAYPAL me at [email protected] to take advantage of the pre-sale …

My SAX 1200d just got shipped today from DB-r I can't wait to get home from my deployment to install that bad boy I believe my Fi BL 15 is going to LOVE it. I just had to share!!!

sup forum. I'm wanting to upgrade my front stage . i have a saz 1000d with an icon 12'' box built to specs. i'm leaning torwards rainbow slc 265.25 since my id CX.62 v2's blew ( friends borrow + drinking = blown ) the amp i have for them is a cheap performance technique. i was wondering if the sax 125.2 is good for frontstage.. simple question but i want to confirm before spending $$ thanks!

well yesterday i went to install my sax 50.4 and the amp turn on but when i hook up my speaker there was no sound. Well then today i went to turn my radio on to power up the amp and it was in protection mode but when i unhook my rca the protection mode goes away but the blue led doesnt light on when i unhook the rca

can a sazx-100.4 handle 2 ohm on bridge mode?, if any one have try it before, let me know thanks

I know the sax-100.4 can handle 10-16v but what about a lil above that. lets say from 17-18v. Im trying to run my whole system all on 16v eliminating the extra 1/0 wire running from under the hood and adding to the 16v charging system. thanx in advance

This is a direct replacement for our old SAX-100.4 model as it is a Class-A/B model amplifier. It is much more compact than the old SAX-100.4 but not nearly as compact as the SAX-125.4 model. We have had a great deal of demand for this unit as it is significantly less expensive than the SAX-125.4 model and is perfect for those that don't need such a small foot-print or a 19v stable amp (these are stable up to ~16v). They are available NOW for $400 from any authorized dealer in the USA. -----

Just looking to find out since I cannot easily see it posted already anywhere... If I get (2) SAX-1200Ds and link them together, what kind of output would I be looking at?? Mainly looking to find out if it is 2ohm stable if linked as well.. Thanks for any help fellas..

This is our second full-range Class-D / 19v stable multi-channel to hit the market after the SAX-125.4 model. It is a VERY compact unit designed to fit just about anywhere. They are available NOW for $400 from any authorized dealer in the USA. ----------

i am gettin alot of question lately about this, and it seems to put off alot of people that ask for a passive set up front and a 2 ohm subwoofer. and they been asking me if i can check for the SAX100.4 for 2 ohm bridged ability. can anyone test this? i only tried for a few mins on a low power subwoofer , without any special faults. no excessive heat, no protection, no audible distortion, i was wondering if anyone could bench the 100.4 @ 2 ohm bridge usability. it could be great to find out that it can do this:) thanks Eli.

Of these 2 4 channel amps which would you get?

I got a sundown saz-1000d in trade.since dont have any subs yet i unhook my four channel amp to see if the amp worked. when i turn my radio on the fuses pop.i only hook up the power and ground the remote wire and the rca up.i was thinking it could be doing this because im using 8ga wire and i have a 80 amp fuse under the hood. when i hook my four channel amp back up to the same wires it works just fine. i went to the part store and to get my fuses and everyone pop on me.i replace the fuse with 25 amp fuses.what could be causing my fuses to pop?

Everything was working fine last night. This morning i turn on the car and i can hear static coming from the woofer. I figured it was the subwoofer coil rubbing or something. Well i try 2 other subwoofers and i get the same result. Everything seems to work fine except there's static that kind of sounds like rubbing styrofoam together. I tried everything to rule out other components and still the same result. Strangely enough the amp works fine apart from that. So i have no clue what to do now. Do i just send it in to get repaired or what? I never thought i'd have any problems with it. Any help would be appreciated.

Hey guys i'm new to the forum pretty much and i drive a 2011 camaro. i got that sundown amp with an incriminator audio death row 12.... i took it to the most reputable shop in town and asked them to install it. i've taken three cars to this place before and nothing has ever went wrong. They hooked it up, said everything was great, but they had set the gain on the lower side as i would need to break in the subwoofer for awhile and go easy on it. that was fine with me because i wasn't really gonna start slamming til i replaced my door speakers which will happen around late october. well the system worked fine the first day, it sounded amazing, better than anything i've hear…