Sundown Audio

So I am in need if the address to send my nightshade in for a recone. Thanks

I have 4 Dual 2 subs and i want to hopefully run 2 3000's so each amp will see a 2ohm load. with them strapped will that make the amps run full power

We will be closed Friday for New Years.

when i was running my btl 15 off this same elec. i never got voltage issues this low(12.8 and under)... i just installed 2 ns 12s at 2 ohms strapped and i am getting the issue, gain at a quarter and volume at half... i have a ohio gen 180/225 ho alt sittin here and will be dropping it in... i also did NOT do a big 3 yet, but the factory wire is 2 runs of 8, will be upgrading to all 0guage soon. with all this accomplished should my voltage maintain a good number. i was also told that since i am running the power between 2 subs now that it maybe drawing more... is that true?

Here is my set up......so far Head Unit - Pioneer Premier DEH-P690UB Front Stage - Hybrid Audio CLarus 6.1 Sub - Image Dynamics Q12 (DVC)...just one Question is which amp would work best....the SAX 125.2 (bridged) or the SAZ 1000D? Also, I'm looking at going active setup. Will the built in crossovers in the SAX 100.4 work as an active setup? Thanks

Hey i have a sundown Saz-1000D amp and my dog chewed through my bass gain control wire. I just wanted to check if there was a certain type of replacement wire i should get or if it didn't have to be the same exact wire. and where do you get those wires? thanks for the help

After reading the FAQ, it seems that the speaker wire outputs are parallel wired inside the amp. I'm trying to wire a SAZ-3000D for a single one Ohm load. Do I need to sum the positives and negatives outside the amp or can I just pick one set of + and - and get the full wattage out of the amp. Thanks. Carl

Well I ordered a Sundown SAX100.4 and a SAZ1000d for my brother yesterday. He drives an 08 standard cab Chevy Full size. He will be running PPI 365 CCS components, a DD T1510 in a PWK enclosure and KNU wire. Only thing not ordered is what the factory deck will connect to processor related. I am leaning toward either a Cleansweep or Alpines H650. Can't wait to get the stuff going. For under 600 bucks for amps... What a bargain. Will have the install on here when we start.

ok im sure this info is somewhere but i cant seem to find it.....i have a dual 2 ohm Btl 15 and want to get 2 1500's to strap....are they 1 ohm stable when strapped or only 2

Here are a few vids I shot of the cracked night shade in action powered by my new purchased 3500. Thanks for the enclosure tip jacob sounds great. Dont beat me up on the install so busy working makeing everyone else car look good. Its just temp. anyway going to send it off for a recone soon.

Im thinking bout picking one of these up for my daily Warden set-up. Wanted to see what tests have shown in a standard 12/14.4 volt set-up, id be wiring to .5 ohm.

are 3-4 years working with the company as a distributor of the brand in Italy, and I have been here to see a lot of improvements that Jacob was able to do in recent years. A major expansion of components, management, and fame! I'm really happy with this working relationship Unfortunately, the only advice I can give to Jacob is this: He has complete control of all business matters I guess. Purchases, sales, inventory management etc etc etc. Unfortunately, having an excessive workload, I do not think he will be able to solve everything himself. the main problem for us distributors, is the immediate response to our requests and our orders. One of our order, customers can mee…

We did pretty good this weekend, here are our scores: Jeremy McCord 2 3000Ds and 2 15" Nightshades Drive-by 4 - 1st place with a 129.8 Mod 3 - 2nd place with a 148.7 Drive-by SPL best of show Corey Mitchell 1 1500D and 1 12" PBX Street 1 - 1st place with a 143.3 Drive-by 1 - 1st place with a 117.3 PHAT 12 award Derek Jackson 2 1500Ds and 2 12" Nightshades Street 2 - 1st place with a 148.6 Josh Newton 4 1500Ds and 8 15" MA Audio XLs Mod 4 - 1st place with a 155.0 Drive-by 5 - 1st place with a 126.? (I will edit with the exact score) SPL Best of show Here are links to the pictures and videos: http://www.carlisleacoustics.com/albums/th...ls.php?album=46 Corey's Drive-by Run …

ok guys im not sure if this is the right spot, but i am using a sundown saz 1500d. i have a pioneer premier 5000 spl 12' like scott owens used, and i have a show sunday and i need help on a box the box i have now is 1.7 cubes with 12 sq port at 38 hz and the highest i can get out of it is 141 this is how it looks now>>> http://audioforum.termpro.com/topic/35/1446.html now i need help cuz i want at least a 144 to 145 i have a marine battery on the amp like 800ah or however i am supposed to tell you the size im not sure the new box i am planning is 2.5 cubes 40 sq inches @ 35hz any help will be majorly appreciated by the way i am boogie woogie on termpro

Corey Mitchell 1 Sundown 1500D and one 12" Nightshade @ 34Hz 1st place Drive-By 1 with a 116.5 (40 amps of fusing) 1st place in Street 1 with a 142.1 (40 amps of fusing) Jeremy McCord 2 Sundown 3000Ds and three 15" Nightshades @ 43Hz 1st place in Drive-By 4 with a 129.7 (320 amps of fusing) 2nd place in MOD 3 with a 151.2 (145 amps of fusing) Josh Newton 4 Sundown 1500Ds and 8 15" MA Audio XLs @ 31Hz 1st place in MOD 4 with a 155.2 (240 amps of fusing) 1st place in Drive-By 5 with a 127.7 (no fusing) Derek Jackson 2 Sundown 1500Ds and two 12" Nightshades @ 50Hz 1st place in Street 2 with a 146.5 (60 amps of fusing) 3rd place in Drive-By 3 with a 123.9 (160 amps of fusing)…

I want to run 4 infinity kappa 6.5 2 way. What is the best starting point on the crossover? Set both crossovers at full? I am new to all this and have searched and searched but it seems most people are using this amp for componets. It will be ran off a Alpine cda 9886 which they advertise has a high pass crossover bilt into it for the front and rear preamp outputs. Will this amp do what I need it to do? The moer I read the more nervous I get that i made the wrong choice. Thankyou.

They made it in... pre-orders will start shipping today.

Designed a slot ported box that will hold 2 E8s. I was told by a few people that my design didn't work because the tuning was lower than the FS # of the sub. Subwoofer Size: 8 inches # of Subwoofers: 2 Cutout Diameter: 7.25 inches Mounting Depth: 4.5625 inches Enclosure Details Port Type: Slot Port Port Tuning: 35 Hz Port Dimensions: 9.25 x 1.625 inches (Height x Width) (port length is not displayed) Port area: 15.03125 square inches Number of Ports: 1 Net Internal Volume: 1.1 cubic feet Port Volume: 0.3123 cubic feet (includes displacement of port materials) Subwoofer Displacement: 0.0500 cubic feet per subwoofer Total Internal Volume: 1.5123 cubic feet Front Baffl…

here goes... i had an old speaker book... in the wiring diagrams it shows a "phantom" wiring series... it shows on a 2 channel amp.. 3 speakers ran and it stays at say 4 ohms... 2 speakers hooked up normaly, then the 3rd is left + and right - can the sundown roll like that?

got my second amp today. woohoo! i took out he current amp pushing the XXX and will be running this one in the mean time in case if any problems come up while in warranty. since my next set-up will not take place till Feb-March it's better to test now then later.. anyways thanks much for the amp. it looks great and works just fine! now all i need is a new alt and tons of tons of sound deadener. off to watch ATHF movie and have some yellow rice and black beans.. woot!

SAE-1200 FTW!!!!

i have a d1 nightshade 15 and i was wonder if i could use one sae-1200d to each coil? if so would i wire each coil at 1 ohm?

Hey guys i had a fast question to ask! I have a new h/u a kenwood KVT-817DVD single-din flip out monitor and it has a processor which it uses inconjuction with the deck. It has a sub pre-out but ONLY 1 and not 2 RCA out puts for the sub. So i was wondering if i need to use 2 sets of RCA's to plug into the amp or can i get away with 1 rca and just turn the gain up? amps: SAZ2000 and SAE1200 sorry if i am unclear on what i am asking. ALSO how do you calculate impedance rise? or do you just hook your DMM meter up to the sub after running the sub for a bit? also i have heard of a device called a AM-500 Accumatches and i was wondering if they are any good? or worth the in…

As the title states. I will be on an actual vacation for the first time in ~6 years or so. The rest of the crew will still be here at the shop holding down the fort. You can still reach Brandon and Debbie as you normally would. Some things may be delayed a bit that require my attention but most things will get done no problem.

I just thought that I would post the results of our team from this past weekend's MECA event in E-town, KY. I didn't get any good pics from the show because it was cold and I was to busy trying to stay warm. Corey Mitchell 1st place in Drive-by 1 with a 120.5 30 second average 6 feet outside of the car. He is running one Sundown 1500D and one 12" PBX XS sub. Brent Howard 1st place in Amateur Street 3 with a 147.6 He is running one Sundown 3000D and two Audioque HDC3 15" subs. Derek Jackson 1st place in Street 1 with a 144.9 he is running one Sundown 1500D and one 15" FI BL sub. Jeremy McCord (me!) 3rd place in Mod 2 with a 147 I am running one 3000D and two 15" FI Q subs…