Build Logs

Heres my first build log, my setup is going to be two 12 inch DC Audio Level 4's with the Level 5 coils and dual 1. Sundown audio 3000d KnuKonceptz Wire 1/0 Rockford Fosgate Fuses Lightning Audio fuse blocks 2 Deka Intemidators 9a31 H/O Alt Santa AKA the UPS man brought me some goodies Coolest way of tightening wire to the fuse block two different screws one on the side and one on top RF 300 amp fuses Fuse Block 25 ft of power Ground 1/0 size 15 ft of 1/0 ground My Box: 4.38 cu foot made of 1 inch MDF 4.10 Net after displacement of sub woofers.

top and bottom getting it square temp roof brace

Here is a few pics of the whole trunk with Fat Mat rattle trap (this stuff is half butyl and half asfault). Trunk Lid Floor Area left side Right Side Latch area Here is a few pics with the new rims. They are 24 inch Menzari's with 255/30/24 Nexxon tires. I know a few of you are going to like my license plate. You might have to click on pic to view the whole thing. Passanger side Close Up Rear Driver side Front Driver side Here is my set of Rainbow 3 ways I just put in. plate put in place of factory 6X9's Factory 3" Cut out to a 4" size after factor 3" replaced with rainbow 4" Here is pics of all the wires that make up the madness. Here is a pic of the amps…

....OK.... after i changed my mind a million times over equipment,car and all the other things ....my build is finally getin started This is my first "BIG" build (i have done some litlLe things for my friends) that iam doin myself and i will try to make it simple .... so lets start with the car ... nothin special (i like it) ---> its a 1998 Hyundai Coupe still in great condition .... and for the equipment .... some wiring stuff ... headunit Pioneer DEH-P6000UB ...amps for front and rear .... Xetec GRAVITY 4G-600 mk2 (used) for the sub .... Ground Zero GZTA 1.2000 front speakers Infinity REFERENCE 6513CS 3-way rear speakers Canton QS 2.16…

Figured i would go ahead and start a new build log Ive been on here for a while just never posted here much, most of my time is wasted on CA.com, gonna start wasting some more time here now also just gonna copy some stuff over, so some things might not make too much sense Pulling out the 4 15s, putting in 4 12s in a smaller box, Vehicle is my 04 Explorer Setup will consist of Kenwood DDX812 Rockford 3Sixty.2 RF T6004 RF T4002 RF T40001bd 4x DC Audio LVL 4 12s Hertz MLK2 running Active old setup was same, just with 4 15" RF T2s in a 16cu ft wall, which was an awesome build, i just decided walls arnt my thing, want to step to somethign smaller Also the reason i have all RF,…

I'm copying this from ***.. Well I guess I'll post up here too. Here's the 'daily'. 2005 Blazer. 4.3 V6 Automatic. A/C 4x4. Its got about 60,000kms on it. My dad and I started on this box. I had wenn_du_weinst design this for me. Its tuned to 35hz, I can't remember if he told me the airspace. Day one looked like this. Knocked a little piece out.. Lookin down the port. Bottom of the box.. Day two I glued the second baffle on, and cut out the sub holes. This is the second time I've used a jig saw, first time was yesterday when I cut out a mount for y CB out of some left over mdf. I think the holes turned out okay? Its all glued inside on the seams. This is what …

I recently did a Cadillac Escalade ESV for a buddy of mine with (2) Fi BL 18's with the flatwound coil and cooling option. Built the box to 14.63 cubic feet with the port tuned to 33 hertz. Wrapped it in vinyl to match the interior of the vehicle and did a big "Fi" logo on the back of the box (notice the logo is an "innie", not an "outie".The amp, for now, is a Hifonics BXI2010D that puts out 1752 watts RMS. I will be swapped with a Rockford Fosgate T40001bd eventually. Built to be a daily driver. Here it is: Sounds great. Real nice quality and it really hits the lows nice, but it just isn't near as loud as it could be with the right amount of power goin…

"OK, lets revive this build log. I need you to post what you are gonna be running in your wall. I need to know the subs, the amps and the batteries that are going to be used. This is the information i got off of your video, if it does not match up to your Aviator, let me know immediately before i start the build process. Baffle = right behind front seat area Height - 42.25" for baffle height, 38" once over the hump. Width - 50" in baffle location, 44" wide throughout the rest of the vehicle. Width 2 - 41.75" wide if box goes to the headliner.. Depth - 37" on the hump, 63" total. 2 questions i have- Depth - am i to assume that you can use 26" of depth in between the hump…

Here is a few pics now that im done. Finally got this damn cam. The alt bracket had to be bent out of the way but it worked. The grounds on the frame are welded on bolts cause I thouht it would be easier. This alt is a BEAST! Thank you Mechman! My power is incredible right now! I hope the regulator isnt set too high. I never touched the adjustment screw and installed it how it was. I thought it came set for you between 14.4-14.9. Is that right? My gauge never gets to 14. It was always over 14 at start up before, but now its just a litle more. Before at 3/4 volume I could get the batt LED light to come on within 5-7 seconds of play. Now...now is a different story.

Got it started almost finished now. I'm about to finish sanding and start paint tomorrow. Lots of pics that will be posted tomorrow as well. 3 4" aero ports cutesy of precision ports. It is going in a 77 Couger. EDIT: Forgot to mention that they were 12's

Got my stuff from Sundown yesterday! Heres the start of a lot of work to be done and a lot of money to be spent over time. The Second Skin is on the way, keep checking back! 2x SA 12's 4DVC 1x Sundown 1500 Big 3 I am not a professional box builder so don't pick on me. It turned out pretty good.

Okay, this is my new topic, because old one was messed up. Here are some info about stuff i have Head Unit: JVC MP3, KD-G401, 4x50W Wires: Ground Zero 4 Gauge Wire kit Front: Signat L13 midwoofers Tweeters: None (coming) Back: Pioneer TS-A6911 6x9" Subwoofer: JBL GTO 1514, 15" Amplifier: Kenwood KAC-9104D, Class D monoblock I also need other amplifier to my back speakers and other HU because when woofer is hitting it can't read CDs. Here is my current setup. Here is a picture of hole between trunk and front, i need tips how to make good box for this, to get all bass in the front. I hope you understand my english, i will also keep uploading pictures o…

Huge thanks to Jacob @ Sundown for hooking me up with a combo of amps that does more than I could ask for!! Thanks to Pipo and Scott for doing the custom Ascendant Dust caps for me. Thanks to Aaron for building the box for me. Thanks to Travis and Tony for helping out with putting the car together. Best team mates in the world.....by far!!!! Things left to do: Buy batteries. The stock one isn't going to last much longer. Build trim panels for the front and rear of the box. Permanently mount box. Clean up wires. Deaden doors. Sealed back eminence 8's in rear deck add another Sundown 125.2 Equipment List: Source - Alpine IDA-X305 Changer - Alpine CHA-S624 Door Speakers…

ok, let me start by saying this is my first time using deadener. so i working early sat. morning on my door, thanks to SS on the free door pack. Damplifier Pro, sorry for the kinda bad pic lol Driver door stock without plastic cover inner door, this was the biggest PITA to put on, i also managed to cut myself with the deadner lol some more deadener All done with driver door stock plastic cover back on the install of the driver door took about ruffly 1 hr. it was too hot outside to continue on with passenger door lol. will finish passenger door next weekend. so far i dont have any speakers installed but road noise on the driver side is noticibly(sp) less then …

Ok so my cousin needed a new box so i made him one using the box calculator on the RE site and here it is... 3.25cubes tuned to 33hz here is the box in the truck forgot to take finishing pics and the amp pushing it Soundstream 1200.1 Stealth Xscorpion wiring

well ive decided to put a system in my towncar and i think im goin with 2 dc level 4 XL's and 2 2000 watt amp

some new vids with the rd audio d9 and 2 treo ssx 18's

What do yall think about this?? will be going in my single cab 95 dodge ram here are the particulars.... bottom 77 x 49 bottom 77 x 49 top 77 x 49 top 77 x 49 baffle 74 x 46 baffle 74 x 46 front 46 x 5 front 46 x 5 side 77 x 16 side 77 x 16 side 77 x 16 side 77 x 16 Port internal sides (4) 3 x 9.5 port external top 44.5 x 3 port external bottom 44.5 x 6 port external sides (2) 3 x 9.5 we are looking at 10 sealed and 17.75 ported get dowels for bracing... 46x10 for the cutout to cab 10-11 feet of wood dowels for bracing... i mean the dowels are 12 inches apart fiberglass resin first then cover in bedliner... also resin the corners and dowels on…

OLD SETUP: 144.3 db with a brand new TL meter legal at the windshield (1) DigitalDesigns 3515d sub 3.5cu.ft box precision ports tuned to 36 sub up ports back (1) Rockford Fosgate 1000a2 amp 4awg power cable Stock alternator Stock battery Here is a picture...This was the 3rd box built for this sub(1st with precision ports) and apparently there was too much port, so I blocked off the center port hole and it sounded better, and was louder. ---------------------------------------------- NEW SETUP: ??? db (1)18" Ascendant Audio Mayhem 8cf box w/ precision ports tuned to 35hz sub up ports back (1)Hifonics XXV Colossus amp 3200rms@2ohms (1-run)3/0 welding cable from front to…

I built a ported box for my rlp-12. It's 2.2 cubes tuned to whatever it is. The port is 34 inches long and goes from 1.5 inches at the start to 3.5 inches at the end, i don't know if that would change the tuning or not. I based it off a 2.5 inch port and took an inch off of the beginning and added one on the end.. Outside dimensions are 22.5 x 22.5 x 14.5 inches. Im not going to do anything else to this box cuz im gonna scrap it. My gear my box having some fun with the box my half ass install doesn't the box just look all pretty. im gonna make a different one for the sub. This is the best sub i've ever heard. I just wanted to take it out for a quick 20 minute driv…

Here is my 3rd system in this truck. 1st was 2 12" Memphis PR's in SMALL PreFab Enclosure, & Cheap 400 Watt Amp 2nd was a 10" SSA Icon in Ported Box built by Audibel Customs & MTX 600 Watt Amp Now 3rd: Audioque 12" (Purchased Online This Morning) , 2.20-2.50 Cu. Ft. Tune to ~37 HZ ~32 Sq. In. Of Port, HF 1000.1, Second Skin on rear cab wall This will be the first box I build for a system so I'm hoping all goes good. Second Skin Arrived & Installed Also Purchased a Tox Kit from eBay to remove seats HF 1000.1 Pioneer-5000UB & Flash Drive & Amp Bass Knob Wiring under driver seat that's going to get organized. EDIT: Also Box Design & I'll ho…

here is a quick vid of my system ripping my spoiler off lol my wife was not happy My link

Hello…my name is Dobson and I am a mechanic in the army…currently doing a tour in Iraq…with a good understanding of how to do installs…I am writing this to ensure that I have touched on every major aspect of my new install for my truck…I will try to be a descriptive as possible…so here goes nothing…I have a Chevy Avalanche…I will use the system for daily use and compete to see what it will do…my sub box will be single chamber and will take the place of my mid gate…I want to get two Fi BTL 18s…dual one ohm…subs will be wired in series to get two ohms from each sub…I will wire the subs together in parallel to equal one ohm…the amp I want is a Rockford Fosgate T40001 BD…wire…

won a door pack of damplifier pro over on *** (thanks ant ) and got it all in. put it on my hatch instead of my door tho. the hatch was in way more need of it lol. stuff is NIIIIICE! very nice quality. here's some pics, and a tiny comparison vid at the end ballin! took the panel off first. probably will paint it black before it goes back on all the areas i have to cover took the clips to this off to make it a lil easier

Well this is the first transmission line box i've ever built.. I read the tutorial yesterday on how to build one and didn't think it was that hard, so i built this one this morning in my spare time. Took about 2 hours to cut and assemble the box.. After getting it done i put it in a chevy s-10 blazer, with some kind of off brand amp pushing only about 300-400 (sad but that's all he had. Haha..). And with that little power running to it, everything flexes in his truck, and it's loud from 25hz all the way up to 60hz.. I'm very impressed with t-line boxes, and i find them easier to build than just regular ported box.. Haha.. Specs: Fs of a D1 Fi Bl is 35.2 Box "port" is exac…