Amplifiers / Head Units / Processors / Electrical

Well i got that JVC HU, it goes up to 34 or something when i turn it on 19 all the speakers start making cracking noise, including subwoofer. I know that this HU is piece of sh.... but what might it be ? Sometimes i can turn it up til 20 and its working fine.

I was just wondering is the Audiopipe AQX35001 a good Amp for the money? There arent but 3 stores who sale it on the whole internet.. It is $475 shipped here http://www.rickiesdiscountelectronics.com/...fier-21902.html $499 plus shipping here http://cardiscountstereos.com/catalog%20pa...ct+%23=AQX35001 and $549 plus shipping here http://www.choicecaraudio.com/Catalog_Page...ct+%23=AQX35001 Here are some of the Specs 1 Ch @ 4ohm: 750w RMS 1 Ch @ 2ohm: 1650w RMS 1 Ch @ 1ohm: 3500w RMS I know that the Audiopipe AP30001D was a good amp for the money at least that is what i heard everywhere. I never personally have heard one

So earlyer this summer my kicker 650.4 got a little hot and burnt up. I was a Electrical Engineering student for 2 years so I know a little about the specific components in an amp. I took it apart and saw that it was a piece I haven't worked with before and about 10 of the same one fried. This is a picture from ROE(the amp guts section). I had my friend take close ups that I'll try to post tomorrow but he is having problems with his camera so not sure. Hopefully one of you guys can tell me what these are and if i'd be able to replace them. They are the first 4 black pieces under the metal on top and bottom and maybe 3 on the next sets of 3. Thanks, Austin

i got a saz-2000 watt amp going to 4 kicker l5 15's, my electrical upgrades are 1 optima yellow top battery 2 runs of 1/0 gauge total 1 pos 1 neg, big 3 upgraded to 1/0 gauge, 200 high out put alt, and 1 die hard platinum p1 in the back, i will be running the amp at 1 ohm, people have told me that i should have much voltage drops others tell me i will, what do u guys think, and i want to get a voltmeter just incase how dou you wire it in

k i have 2 rockford power elite series 1000.1's they are strappable amps and im running 4 l5 15's dual 4 ohm so i wanna strap em first off how do i do it and what do i need currently i am they hooked up seperate thanks

k im loooking for the price on a 12k soundigital amp thanks

im thinking of getting a audioque aq1200d to push a mtx 9510-44 what you guys think

I just hooked up a rf t40001bd amp in my car, the amp is ran by 3 stinger sp1000 batteries and a 250 amp alt. I played it for a good 40 minutes I than went out to listen to it again and pop the amp smoked and the fuse discolored (but never popped... not sure wat else Im scared to put another amp in... Any help would be appreciated

I have been looking at getting the AP3000.1D, but I saw I can get the AQX3500.1 for about the same price, has anybody tested them to see if they do rated?

hi, i am positive that it is my head-unit causing this (it is a alpine 9887) but i am trying to see what else it could be. ok for starters i have my gains set on the my sax100.4 At volume 27 is the max (out of 35 i think) and sometimes when i have the volume at only 15 the drivers mid range will get very notice able louder and i will use the balance and the left speaker is barely playing and the left is acting like it is receiving double the signal. now i have the sax 100.4 running active and i am only using the high on the 9887 to feed the sax100.4 channels 1 &2 and then using the output to feed 3 &4. So if it was the amp couldn't one side play fine and t…

I have it wired but it doesn't turn off when I turn the car off because its directly hooked up to the battery. I'm thinking I can splice into my remote turn on for the amp but I won't get a voltage reading from that will i? I need a way to get the best voltage reading possible and for the meter to shut off when the car is turned off... helpppppppppppppppppppp

hey whats up i need help choosing an amp(s) for my setup, my electrical upgrades are big 3 1/0 gauge, 2 runs 1/0 gauge 1 pos 1 neg, 200 amp alt, optima yellow top front,die hard platinum p1 in back, k i have 4 dual 4 ohm subs kicker 15 15's, i need an amp decision i either want a saz-2000, i would have to run it at .5 ohms will my electrical handle that, and hit hard, or should i go with 2 saz-1000 and both amps would be wired down to 1 ohm, which setup would b louder and which would work the best

My first question when you change the bass level, middle level and treble level it controls all speakers including the ones on the amp? The levels go from -8 to 8, right now I have the bass at -6 (usually its at -8), the middle at 4 and the treble at 8. How do you tailor made these settings. My second question is the bass level has a Bass F(40-120hz, I keep it at 40hz), Bass Q(1.00-2.00, I keep it at 2.00) and Bass Extend (off/on, I keep it on). Could anybody explain what these settings should be around or what they mean (I know bass F is frequency) or if I should even mess with them? My third question is the middle level has a Middle F (500-2,000hz, I keep it at 500hz ),…

Why does everyone run 2 Kinetik Hc1800s instead of 1 HC3800? You get more power and its easier to set up and its the same price if not cheaper. Would this battery also be enough with the two amps and a 200A alternator?

Hi, I am selling my 4 channels Boston amp. I can make a good deal with it, and I don't use rear speakers no more ! I need a small (in size) 2 ch amp to power my Focal 165 KP. I need about 2 * 100 watts rms or even less, and my head unit is good enough, so I don't need lots of features on the amp. The problem is the budget : I want a really cheap amp! But I want a brand new one. The Sundown 125.2 would be good, and would match the sub amp (a saz1000), but I would like it cheaper. I saw a Cadence Xa 175.2 xenith series at Powermax electronics, it looks good ! There is an entry level Rockford the R 300-4 (I could bridge it) that seems good too.(Powermax electronics) One poi…

i have a zapco 2x100 that goe into protect at almost full tile i looked at voltage drope and the lowest was 12.77 volts and it went into protect and i turn the vol down and it starts playing again the ground is good any input?

I'm wondering the best thing I can do to help my situation. It's been ridiculously hot here in San Antonio this summer and my SAE-1200D just isn't taking the heat well at all. My Cadence TXA1000D never had a problem but I guess with the extra power this SAE has the heat is causing trouble. The amp gets VERY hot to the touch and after a while goes into protect. At first I thought I had a problem with the subs cause they would make a strange noise before shutting off but it cuts out even when my HU is paused so I don't think I have a subwoofer problem. Maybe mount something like 2 120mm fans on the bottom of the amp? How would I hook those up? Just wire them to the power/gr…

At work we have numerous rtas used to test the frequency responses of circuits. This is tested through an osciloscope input. My question is if I were to find a mic that had an osciloscope conenctor at the end of it would the rta work for what I want it to do?

Has anyone used Odyssey brand batteries in their setups, and if so, how do they compare to other brands as far as disharge and keeping voltage up?

I am putting in 3 external batteries in the back of my suv. The batteries are obviously going to be grounded to the chasis. I have been confused on whether it would be better to ground the amps to the chasis as well or if it would be better to run the ground to the batteries. The batteries are each going to have 2 runs of 1/0 to the chasis. Which is a better idea?

Does anyone know how to figure out the resistance when i wire a dual 1 ohm sub to .5 ohm, and a dual 2 ohm sub to 4 ohms, and then wire those subs together in series?

Which sounds like a better idea to you. I am in need of a new double din gps radio and i also plan on going active. Here are the choices I can either get the new kenwood dnx9140 sax 100.4 for mids sax 100.4 for highs (will be mostly tuned down since the tweeters will not be able to take 160+ watts of power as they are 2 ohm) i would need to use the crossovers on the amp or the new kenwood dnx7140 rockford fosgate 3sixty.2 (used as the crossover) sax 100.4 for mids sax 50.4 for highs both cost the same or if you feel that there is something better that i should get please let me know

is anyone on here using them? I was looking through their website and found a diagram that shows pretty much exactly what I will be running so I figured I would just copy what they suggest. here's a picture of the diagram can someone fill me in on the pros/cons to running something like that? I know 1 pro would be a much greater tuning capability but not sure on the cons any input/advice is helpful edit: heres a link for the 6xs http://www.audiocontrol.com/t34/5251/18487/Car-Audio-Electronic-Crossovers/6XS-6-Channel-Electronic-Crossover.html and the link for the crossover http://www.audiocontrol.com/t34/5250/14149/In--Dash-Car-Audio-Processors/Three1-In--Dash-Car-Audio-E…

http://www.crutchfield.com/S-KJi47TPlPGC/p_130AVHP410/Pioneer-AVH-P4100DVD.html obviously doesn't cost $400 through them but I found a few sites that sell it for $400-450

i understand fans are useful in keeping your amps cool ... i see a lot of people just using them for their sub amps ... i also felt my amps and my sub amp gets a lot hotter than my 4 channel ... do people mainly put fans just on their sub amps or all of their amps?