Amplifiers / Head Units / Processors / Electrical

Anyway all i have right now is a Soundstream XTA600.2 600 Watts RMS and my Oz Audio Matrix Elite 15 and its dimming even with that. I have been looking around and i cant find that many alternators for my car i had been recommended to call ohiogen to ask? my lights have been dimming when idling especially when the air is on at the same time, i have a 1995 dodge stealth and they alternators are weak on them and i believe i even have the upgraded 140 amp ......it could be the 110 amp thought im not sure, but i was told that i couldn't go past a 140 amp that it probably cant be wound more than that.... I saw this by powerbastards http://powerbastards.com/proddetail.asp?pro…

if on my battery i am running a 2 gauge wire to my alternator and a 2 gauge wire to my amps coming from the positive battery terminal post, is ok to wire one 0 gauge wire from the battery to the frame or does it have to be (2)-2 guage wires going from the battery's negative terminal post to frame. in the long run after running two batteries i will come up with close to 5 ground wires that needed to be grounded to the frame and i wanted to lighten the load if possible but if not its cool.

hey guys again with some noob questions Tomorrow i am going to start my build be for i get far into it on my old setup i had an extra battery i had the negative on the second battery connected to my main battery since there both in the trunk so my question is was that wrong? should i have the additional battery's grounded to the frame? if i am right about my mistake i am thinking of grounding my additional battery's to the frame. then power from main battery to second then third battery and a fuse from battery 3 to amp? that correct?

i bought this deck yesterday and it comes with the demo mode on, in the insructions it says to push and hold the volume knob in for 2 seconds and it will switch it from on to off, and off to on depending on what its already in, but when i do this the mode is still on, can anyone help me? it would be greatly appreciated

A quick question I am planing to buy this wire from knuconcepts when it asks me to choose fuse size what do i pick right now i am running a dc l4 12 with an aq1200d. i want to upgrade in the near future with 2-3k watts:) the question is it fine if i get the 300 amp fuse? http://www.knukonceptz.com/productDetail.cfm?prodID=KFX-PK0

I just bought an 18" BTL daily driver fully loaded. The question is which amp should I buy to power this beast? I lookin at the RF T20001bd or the Sundowner 1500d. I know the RF might make more power(2000vs1500) but the sundowner is just a little more expensive. Can anyone tell me about their experience with this brand? (sundowner) I never heard of them before but I hear they are excellent. Please leave a little feedback on what you like and why. I want to slam hella hard for my weekend cruiser(91 Silverado) as I already have a commuter car with 2 15's. Any suggestions are welcome. Thanks guys.

So here is my system so far: ID CTX65CS comps SAX-125.2 for the comps AQ1200D amp SDC2.5 12" sub Now i was told by the only good car audio place in town that the 9887 is the way to go. I read on here that there's really no reason to buy the 9886 (or anything at that level) and that the OP should either go up or down. I'm not planning on buying anything new, at least head unit wise, for a really long time so I don't want screw up. I really don't know too much about head units. I haven't even bought one....I have a sony xplod that came with my first car, and I still have it (its been about 2-3 years). But that HU just isn't gonna cut it anymore. I figure I'd be fine with…

i was looking around on the net i saw this amp audiopipe 30001d its 30inch long wow has anyone used them? you can get them for cheap 400 also has anyone used the 2 channel and for channel amps?

Okay so im asking this question for a friend of mine. He just recently bought a hu from a local shop and they do free instal with the purchase...well they said that his car has a factory amp and that they will have to by pass it by running all new wires which will cost $120. I am still learning but this just doesnt seem right. I mean why would you want to bypass a amplifier? The shop said that running the amp would equal less output to the speakers but bypassing it would make it louder. I just dont quite understand the logic so if someone could explain it would be great. thanks

Im getting a 18' Fi BL 1000watt Subwoofer and I have no idea what kinda amp to get...Im looking to spend under $250...what kind of specs do i look for in a amp?? ALso i have the choice of getting a 1 ohm or 2ohm subwoofer wtf is that all about i have no clue???HELP!

ok, for setting gains with the DMM method, do i use 0dB tones, or can i get away with using, say -6dB or -3dB tones? I've heard recommendations for using as much as -6dB tone (that seems a little much to me) so i guess what I'm asking is how loud does most music get? does it regularly hit 0dB, or more like -3, -6, etc?

Hey anyone sell a varible subsonic filter?

Well I decided to pull all my "big boys" outta the closet... time for some pics and testing... I'm really doing this to find out which amp will be the most efficient for my next install. The competitors Sundown SAZ3000D, Massive Audio P3000D, Swiss Audio SDX2000A, Clif Designs CD4800LX(amp is sold,pics only) , Visonik 4000

ive been looking for a decent amp and i ran across some forums sayin that the fusion 4000's are good amps, so how are the others? or is the 4000 the only decent one? im lookin at the 3000 for $228...

yay or nay? i have 2 alpine type r 12's

on my highs amp, im running the power wire as 8 gauge and the ground wire as 4 gauge(i was told this was ok by a friend and professional installer). im not doubting his credibility, i just wanted to know what are the advantages and disadvantages if there are any to wiring your amps this way

I'm working on a little project where the only available power source is a 12 cell Ni-MH pack, starting at 16.8V fully charged, but dropping to 15-16V after some use. Would a HU run on this, or would it go up in smoke?

I just got and installed my alt from DC. First of all before w/ my stock alt I would idle at 13.8 and drop down to 12.4 at the most So I figured the h.o. would help with that problem, I talked to Rob from DC, when I first bought the alt and he told me it would be a good idea to get a module, so I would charge at higher volts. Since I didn't have the money at the time. I didn't get it yet. But anyways, I put the alt in; and I immediatly notice that I was idling really low. I checked it with Dmm and I was infact idling around 12.8. Now I know it would PROBABLY help if I add the module, but since I was already idling at 13.8, shouldn't adding the H.o. still keep me around t…

I was wondering if I needed to solder the ends of my power wire(1/0 knuconcepts) before i put it into my amps. Same goes for the speaker wire going to my sub and speakers. Also, can i just get a cheap battery powered soldering iron, or do i have to get a nicer one? thanks.

Was wondering if anyone has one and how accurate is the db meter? Is it worth playing around with. I seen that they made a couple of different models with the spl meter.

I have an aq2200d that will be powering a ss rl-p 18 at 4 ohms. When i go to wire it up, do i use the outside pos and neg ports on the amp? Also, i have a kicker 200.4 for one set of components. I want to bridge the amp to make 100.2 at 4 ohms, but im confused when it comes to wiring it. there are two rows of inputs for speakers. one row says amp 1, and the other says amp 2. would i just do one speaker on one row, then the other on the second row? sorry its confusing. ill try and find a picture. http://www.sonicelectronix.com/pictures.php?id=11366

i have 4 cvrs in two boxes they are wired in the box and are ready to be hook up just need help hooking all four to mono amp.

Hi guys I hope all is good. Years ago we all had capacitors in our cars ( 1990's ) and later we went to the Batcaps. Why did we stop using them?? Did batteries kill them off are what? Are do people still use them and I just didn't see them?

well i have a amp (cactus 5kw) and it has four speaker terminals and im trying to hook up a 2ohm load to it. my question is if i hook 2ohms up to it will it be 2ohms or would it bridge it down to 1ohm?????? thanks

I was telling my dad how i am going to buy another battery for my truck soon, for audio, and he said that he thinks putting the battery in the cab is illegal? I'm not sure why it would be and i have seen almost everyone on here put them in the cab. Is it illegal? I live in Texas if that helps.