Amplifiers / Head Units / Processors / Electrical

well my 160a2 rockford amp is not working so i opened it up and found that a resistor was blown it was brown around the area it was in. I think i can fix it but i dont now what part it is i need there are so many different resistors. The one on the amp has four band the out side ones are like a brown gold color and the middle ones are some dark color.

long story short. stupid on my part. but i am in the process of getting a thing built so i can hold my box and amp down, without having to screw into the seat or false floor. so for the time being it is freely hanging out in the back of my jeep. the sub slides around alot, the amp barely moves. well saturday night i was driving around with frineds, and went to a part of town i rarely go too, and witht he fresh snow on the ground i didn't see a speed bump (no signs...) well i hit it and i looked int he reiw view mirror, i saw my sub slide, but not really go in the air. i heard my tool box fly up, and i'm assuming my amp did too, as they were by eachother. after it landed,…

Well i decided to change things up and bought a kicker Zx700.5 so far so good it looks amazing, here are some pics. now for the new sub, i was thinking skar...only time will tell lol...

I am looking at a arc xxk4050 amp that is a couple months old he wants 300. for it. Is that a good price? the sheet says 118-120 watts a channel. I have heard a lot of good things about arcs but never heard more than a couple minutes in a demo room

Amp is from 2001-02. There was a mod for it put out more power. I can't find it anywhere. Thanks

I have seen these for around 400-500 dollars. same board as the MA 4000 and cliff designs. Does anyone have experience with these do they do rated or close on a good electrical system? would be used for daily and some comps. thanks Chad

Hello i am relatively new here and was hoping to gain from the experience of some other members i am currently using a Sony CDX-GT340 and it sounds okay, but i was told the sound quality could be much much better. i am running alpine type r 6.5 components in the front and pioneer 4 inch (3 way) coaxials in the rear doors i am hoping to run these speakers off the head unit for a bit longer and then i will amp them my subwoofers are 2 15 inch fi Q's in a sealed box each receiving ~1200-1300 watts from it's own rockford fosgate t1500-1bd (currently off a y splitter of the rear channel) (electrical system has been upgraded significantly to account for this i don't want a…

So looking for some info about amplifier and efficiency. I have a xcon dual 1ohm 10" so i can run at either .5ohm or 2ohm What i would like to know is 1500w @ .5ohm or 1500w @ 2ohm the 2ohm amplifier would be drawing more power to make its wattage because of the higher resistance correct ?

B) http://www.mtx.com/caraudio/products/amplifiers/indexMXA.cfm above is the link to their site, I was wondering who has used or played with them, and are they the step up or the entry level?

Right now i have a duralast yellow top under the hood, and i was thinking of adding a second battery. I want something thats going to keep my amps happy but i dont want to break the bank. The list Hifonics Brutus 1208D Kicker KX 350.2 Kicker KX 200.2 DB Electric 200amp Alt 0ga Big 3

hi, i have 2 sundown sd1 v1 12" and i am thinking about using them until i can get enough money to buy to system i really want so if i can limit how much i spend the better. anyway i already have a sundown sax100.2 that i was going to use to power them but the problem being that it does not have a subsonic filter on it. and i was wondering if i could get away with using my alpine 9887 crossovers and my sax100.2 crossovers and bandpass it, if that would ok an ok alternative.

So I just got my 2nd batt and I was thinkin on how to wire it but I'm not sure if I'm right [frnt batt]+----fuse----------------+[rear batt] |----fuse--------------amp correct me if I'm wrong I'm sure I am

Hey guys! Ok, Im about to get two amps for my pickup (JL Audio Slash v2 300/2v2 & JL Audio G1700). I plan on putting them under my seats and both will be powered by 4 gauge cable. My question is this, what scenario would be better (electrically speaking only): 1. I run a 0 gauge from the battery into a distribution block with two 4 gauge outputs to my amps (all fuses will be properly placed). 2. I just run the two 4 gauge cables from my battery directly to the amps (all fuses will be properly placed).

what is a good head unit (preferably JVC or Alpine) that will not skip because of the bass? i have a alpine cda7897 now and i cant turn my music up without the cd skipping repeatedly. really wouldnt want to spend more than 400 for a h/u. its going to a lincoln towncar and i am running a zx2500.1, zx650.4 and (2) 15" btl's

I have a PPI pc1800.2 that burned out. I haven't opened it yet to see what fried but it's definitely dead. I was wondering if anyone knew of a place down in Glendale or LA or even OC that knows where I can get it repaired? It's a sexy amp and I'm not willing to let it go.

i took my equipment out of my car to diagnose a problem. while it was out it was stolen. so now i am stuck with factory power. the problem now though is, the factory system had some issues when i bought it. at a little over half volume the sound from the tweeters cuts out when there is a louder sound.. like a yell or.. scream. or just louder singing. head unit? or amp. 03 z4 by the way

okay well today, im mounting my fuse holders ect... and my question is when do i actully put my fuses in??? like do i start my car then place my 300 amp fuses (4) for my batterys(1 d3400 under the hood,2 d3100 in the trunk) and 200 amp fuses(2) for my aq3500d1 on my amp? or before i start my car i place my fuses in??? idk if that makes sense please answer anyone

Is there any difference between kinetic racing batteries and regular kinectic batteries? I'm looking for a trunk battery for my build and was looking at an HC2000, but I found a better price on the KR2712. Which looks to be the same battery but in a red case. I went to kinectic's site to look up the racing line of batteries. But they aren't listed anymore. Which I'm guessing is why the racing line is cheaper since it looks to be discontinued.

Im about to purchase all of my wiring so i can get started building my system, but i want to make sure i buy the right stuff. My system consists of one ss rl-p off of an aq2200d at 4 ohms, polk momo component set, and a kicker zx200.4 running those. (stock electrical). I talked to a guy at knuconcepts and he told me i should get the 0 gauge kit, with a knd-23 distro block that has 2 0 gauge ports, and three 4 guage ports. He said i should run the 0 gauge kit to one 0 gauge port, the run some 1/0 from the other port to the aq2200d. then run some 4g from one of the 4g ports to the kicker. If that made any sense could you tell me if that works? lol

Ordered my amp! It's an old school Soundstream Tarantula monoblock. Specs are as follows: Continuously Variable Low-Pass Crossover Three Stage Level Input Indicators Output Clipping Indicators Phase Inversion Switch (0 - 180ﾺ) Selectable Differentially Balanced Line Inputs Fully Balanced PS-2 Input Line Output Gold-Plated 1/ ? Power Connectors Discrete Balanced Class A Drive Boards maximize linearity on low impedance loads Drive Delay 2? eliminates "turn-on" and "turn-off" pops and noises Chassisink? Semiconductors are situated between the circuit board and heat sink for optimal thermal transfer Power Grid? design optimizes current delivery to and from the power supply T…

Just thought I would share some information of an amp head to head test I did over the weekend. This is not a post to bash any company just sharing information take it for whats its worth: Test set up: Test set up was using the follwoing Alpine 9874 headunit Test volume 27 Test Hz 74 input voltage to amps .97 volts Two Addictive Audio version 3 12" dual 2 ohm subs (wired at .5ohms) car off (12 volt test) one Xs-D2700 Xs-power charger 25 amps (14 volt test) three Xs-D1600 Xs-power charger 5 amps Amp one: 2.5Kv2 Amp settings Gain at Min 17 volts out Gamn at Max 84 volts out Test setting 82 volts out Amp Two: 250.1 Amp settings Gain at Min 20 volts out Gain at Max …

seen there was a guy with a blazer that had one and i got a blazer how bad does it draw current?how big of alt you got and batteries?

Does the epicenter help increase you spl or does it just act like a bass boost where it will just cause the amp to clip. Would it be a good idea to buy one if I mainly use an ipod?

Alright so I have been waiting to get money for 1/0 wiring and then my friend who is in an automotive electrical class in a local college here messaged me and said that he thinks 4 awg would be big enough for my big 3 Since my alt is only a 70 amp alt and He read that 4 awg should carry up to 150 amps.. At least in that short of a run (1ft-5ft runs) Just wanna make sure if this will work before I buy it in about 45mins. I dont have enough yet for all the 1/0 but I have enough to afford 4 awg if it is good enough now. After he said that i figured well 1/0 can carry more current at a time and quicker.. but.. If my alt only puts out 70 and 4 awg can carry 150.. Is there…

I have just finished receiving my impedance curve measurements for my setup design between 20hz-80hz. Here shortly, the graph will be posted here and in a few hrs, me and a buddy are gonna take a trip to an isolated area where we will be measuring output and efficiency and comparing those numbers with the SAZ1500D as i've always wanted to know if the AQ outperforms the Sundown since it's rated to do more power but only at a higher voltage. As of right now, - Impedance curve ranges from 1.76 ohms to 21.6 ohms. DCR is 0.7 ohms So... i will NOT have any measurements below 1.76 ohms and depending on heat buildup, i'm still hoping to pull some numbers out of the AQ below 2.0 o…