Amplifiers / Head Units / Processors / Electrical

I've got Dodge Magnum R/T with 160A stock alternator and from what I hear from other LX vehicle owners, the car's computer controls the alternator output...so upgrading my alternator isn't an option. So with my stock alternator what do you think is the most wattage I can run on my stock electrical? I know that an extra battery (or three) may be necessary along with Big three. Also, since my battery is in the rear, not under the hood, how does that effect things?

im doing the big 3 with 2 gage but should i ren the - from the batt to stock ground or to a better spot?

i took my equipment out of my car to diagnose a problem. while it was out it was stolen. so now i am stuck with factory power. the problem now though is, the factory system had some issues when i bought it. at a little over half volume the sound from the tweeters cuts out when there is a louder sound.. like a yell or.. scream. or just louder singing. head unit? or amp. 03 z4 by the way

Does any one know what are some good sites to buy amps online.

Which puts more of a strain on alt. Pros and cons of extra battery or cap. I never plan on playing my system with the car off. Just trying to keep my voltage up. Big Three with Kicker Pkd1 coming monday. Stinger Voltmeter coming soon. 2001 Tahoe 2 Kicker Cvr's Dvc 4ohm wired down to 1 ohm Us Amps 4000 Xt and Crunch 1400 4 channel.

Ok. Ever since I can remember I have had a small problem with dimming headlights. However, I never really noticed because I don't blast my system full tilt very often and hardly ever at night. For some reason my lights seem to be dimming a lot lately. I currently have a 200amp alternator with 3 deka intimadator batteries. This powers my saz3000d at 1ohm. I thought that I might have a loose connection or my alternator was failing. I started testing voltage and this is where I'm confused. With the bass at nearly full tilt with the lights dimming bad my voltage stays at a steady 13.98 volts. With nothing on it's charges at 14.2. So, my question is how or why is my lights dim…

a friend of mine has a pioneer avic-f90bt and he is running a 300/4 and a 500/1 when he has the balance/fade centered, it cuts out all low and mid frequencies, when he fades it all the way to the front or to the rear, it plays at a normal full range strangest problem i have seen. i have yet to get in there for my self, but i asked him the following, how many sets of RCA are being used : 3 are you sure they are all into "outputs" on the head unit :yes did you try another amp : yes a boston 4 channel same issue have you tried another head unit : no he also stated that pioneer has a few updates on the site, i recommended he reset the head unit, and then downl…

Does a car battery need to be grounded to something in order for it to work properly? The reason I ask this is because a friend and myself are doing a school project (we have to design an entire business), and we thought it would be cool to make a movable car audio display. It would contain some OEM speakers from my Lumina, as well as my friend's Kicker L5 8", Audiobahn amp, a Kenwood head unit I've got laying around, and my car's battery that I'm soon to be replacing. We're thinking of hooking the amp and H.U. directly to the battery (well, fused of course), with a switch on the H.U.'s power lead so that we can turn it on/off that way. The ground for the amp and H.U. w…

Gents, Just curious if I can run my Xcon D2s at 0.5 ohms and be good, or should I just run them at 2 ohms? Electrical consists of 3 XS Power D3400s ( 1 as a front batt, 2 in the rear). I ran all zero for the Big 3, and currently have a HO alt of 250a from Excessive Amperage in the works. Just wondering how I should wire the subs on these amps. Any input is appreciated. Also this is a daily driver, if that means much. Thanks.

k i have 2 rockford power elite series 1000.1's they are strappable amps and im running 4 l5 15's dual 4 ohm so i wanna strap em first off how do i do it and what do i need currently i am they hooked up seperate thanks

With two D1 ohm subs if wired in series for a 4 ohm load with two 1500rms 1ohm mono amps strapped would that give me a final load on the amps of 2ohms being there strapped? If wired in series/parallel for a 1 ohm load with two 1500rms 1ohm mono amps strapped would that give me a final load on the amps of .5ohm strapped? Also out of all the researching I've done regarding strapping, is it true that 2 strapped 1500rms 1ohm mono amps be like a 3k 2ohm amp? I posted this elsewhere also n I believe they answered wrong considering everything I find its double the power/ohm just wanna get another opinion in a better worded post

Please someone correct me if i am wrong, i am going to strap my Sundown Audio 3500Ds and this will be my first time strapping amps, so i need to see if i am thinking correctly. The Master amp gets the input from the head-unit and a mono RCA from "BR Out" connected. The Slave amp ONLY gets "BR In" connected from the Master amp, leave the Gain and other Filters on the Slave amp set to 0. Each amp gets its own remote wire coming from the head-unit. Each amp gets its own Power and Ground. Connect NEG terminals of both amps together using 8AWG wires Wire my subs like so; Then take the POS wire from my sub and put it in the Master amps (far left) positive terminal, then take t…

im running 2 saz 4500's to 2 fi btl's and i was wondering should i strap them or dont? what is the purpose of strapping?

Hey guys. So I am going to be running 2 Crunch GP3000D's here in the near future and I am wondering what the benefit of strapping the amps vs. running one amp to a pair of subs? My subs are/will be dual 1 ohm coils so I can wire each sub to 2ohm and let the amp take it to a 1 ohm final load or I can strap the amps and wire all the subs to 2ohm final load. IMO, It would be easier to wire the subs to 2ohm and then run wire from 2 subs in to one amp and repeat for the other subs and amp. Since I have never strapped amps, I am curious what the benefit would be and would it be worth the extra work to try and multiple wires to the sub terminals.

Okay I am some what new to this forum. I have been reading it for quite some time now and see that everyone is pretty helpful. I have a couple of questions about the Fi Audio Btl 18. I see that it comes in dual 1 or dual 2. Well I have a kicker sx 1250.1 and it does about 1310 at 1 Ohm. I was thinking about getting another one and strapping them to power just one fi audio btl 18. Well from what I have read strapping the two kick sx 1250.1 amps together will give me a 2 0hm load which I unfortunately do not want but do you think I can connect either a dual 1 or dual 2 to the amps with out effecting the sub or the amps. I figured if anything it would effect the amp since I …

if you have 2 mono amps and you strap them are u getting double the power to that one channel on the master amp? Does it effect ur ohm load to the master amp from ur subs? like if you wire ur subs together to get 1 ohm would you still get 1 ohm power from the master even if it was strapped? thanks

okay guys it sounds like a noob question which is probley is but im just trying to figure out what i am trying to see as a final impedence i have 2 woofers with .7 coils 1.) if i wire it in series/parallel does that mean i get my amps at .35 each and .7 total? or does each amp get .7 and 1.4 total? 2.) if i wire it in just series does that mean my amps each will see close to 1.4 ohm each? and 2.8 total? just getting lil confused on this any help please

I have 2 audiopipe APSM1300s, i was running them strapped together on a 10" SSA XCON D1 (wires to 2 ohms). So i am not sure if one of the amps dying had anything to do with strapping them, or if the moisture in the boat finally took out the amp. Basically, the amps ran fine for a couple days strapped, and then yesterday when the "Master" amp's power and protection light started flickering very fast, and the sub began making a popping sound, even with RCAs pulled out. I unplugged the remote wire, and hooked the sub up to the "Slave" amp and everything works fine. I took the "Master" amp and put it in my truck and it did the same thing. Looking at the wiring diagrams incl…

Sooooo I feel like a total noob lol. Most amps that can be strapped have a master/slave switch. My atomic AT3000.1s do not. But they are strappable. Now I assume these strap like a saz3000 due to being almost exactly the same amp. Don't post up pointing out differences or bashing my shit. These amps are badass. From what I can see, saz3000 amps do not have a master/slave switch either. Referring to this thread the layout of my atomics are exactly the same minus the fuses of course. On the control/RCA side my amps are exactly the same. So I guess they automatically switch when strapped? Or is there a hidden switch somewhere?

Hey guys im looking to try out the maxx link but i have a question for ya. Im gonna be running 4 kicker zx2500.1 amps and 2 18in Btl dual 1 ohm subs. The zx amps are 2 ohm stable and i was wondering if there is any possible configuration to have the amps see a 2ohm load once strapped. Also would i be better without the maxx link and running each amp to each coil? What ohm loads could i see there. thanks

Can it be done folks?

Whats up guys this is Rp i own a car audio shop in Lafayette IN i am running street c this year and looking for new amps... currently using 4 Memphis 4kw and pro-comp subs. looking at the 3000 watt ssa but i need test results on them... volt drop\ power\ ohm\ and amp draw

Hello, i have 2 SSA ICON 12's powered by two Phoenix gold ryvals 1000watts each. each sub with their own amp. so i keep blowing the fuse and my fuse holder is now melted. so it got me thinking about taking out the inline fuse completely. good or bad?

Hey all, I'm going to buy myself a new headunit my budget is around 250$. So far the ones that catch my eye are the Pioneer premier DEH-p600ub and the Ecipse CD3200. I don't know much about head-units...the pioneer caught my eye because it has a 7 band equalizer while the eclipse only has 3 band. The eclipse caught my eye because it has 5 volt pre-out compared to the pioneers' 4 volt (apparently more volts is better). Visually I like the Eclipse better cause people in Montreal don't seem to have them and looks more classy compared to pioneers blue leds all over the place. I'm hoping someone who knows about hu's can help me out, please help! These are the ebay auctions i w…

believe me i know this is a stupid question but i had an argument with a guy from a mechanics shop and he doesnt believe me: if you have 2 DVC 1 ohm subs wired in series then together to come to a 1 ohm load and run that to a monoblock amp that is rated at 1600 watts rms @ 1 ohm, does that mean each sub gets 800 watts each or do they both get 1600 watts?