Fi Technical

New to the audio scene and was posed with this question.. Lets say I am trying to squeeze a box into my car, and the trunk fully stripped, can only accept a box that is a max height of 15.5". Would it be possible to fit a 15" Fi SSD in a box that was reduced to 15.5 inches tall? Wouldn't that affect the integrity of the box, being that thin on the top and bottom, or would that even work period? More in depth: Id have to bet that there would be a lot of sanding/sawing involved. I am in a predicament, as my sub faces up in my 1st gen mazda 6 sedan. The actual trunkspace has PLENTY of width, and depth, but the entrance inlet from trunk, or seats is not vary tall. As stated…

so i've got up to 15 high x 32 wide x 20 deep to build an enclosure for my fi btl 12; it'd be going in the back of my jeep liberty. and im planning on using this sub daily on an alpine m2000 that i just got and the birth sheet says it'll put out 2274 watts, so i'll be playing it at its max. but i also want to start entering the local spl comps and i know the fi site says that 30-35 hz is where it should be and 32 is optimal, but i was wondering what would be the loudest hz for my application? thanks in advance

Can a pair of Fi Q15's be ported and tuned to 30hz in a properly sized enclosure, if my max external dimensions are 22" (d) x 19" (h) x 38.5" (w)? Less height and depth if possible... I was planning on running them sealed, since I know they have great lowend sealed, but if I can still have great lows with more output, I want to got for that. This is for a Dodge Magnum. My goal is to have the most output while maintaining a somewhat flat response, with the gut twisting lowend.

Will a 15" Fi Q with BP power be ok on a AQ2200D amp at 2 ohms (1300 watts) or will that be to much power?

Hi, i'm Patrick from Germany and i just ordered a Fi BTL 15 with Cooling and HiXM Coil for daily driver. The BTL replaces my old RE SX 15 wich i operated in a aprox. 4,7 cubes box, tuned to 35 Hz.... My problem now is that i don't know how to build a enclosure for the BTL because i usually calculated everything with Win ISD but this doesnt work with the btls TSP'S... Can you help me or say what i have to build. Max dimentions are: width: 93 cm or 36,61 inch height: 45 cm or 17.72 inch depth: more than 100cm or 40 inch I'm running it with a RF T20001bd and kinetik batts.. I hear lots of young jeezy and gucci mane... My Peak with the SX was 141,9 with 45hz on Termlab, hope…

Hi, Need experienced help, I just received and installed my Fi SP4 15 D2, powered by a Crescendo B3500D(the volume on the amp is up to 75% on the gain knob on the amp and bass boost in 0 and on the head unit the subwoofer level is in max), and I feel the bass is weak for what I expected... 1- Is this normal? Or what should I do? 2- Is there a specific way to put the ohm load down to 1 ohm on the sub? 3- What specific grill fits this sub? Thank you.

i am looking to try out a new design in my ranger. this will be for a 15" btl fully loaded. my max outer dimensions are 50 long x 16 deep x 18t all. heres the kicker, i would like the sub in the middle of the box facing the roof and would like to have the ports doing the same on each side of the sub. i am looking to get it tuned to 30-35 hz. the only reason i want the sub in the middle is because my truck is bagged and i want the weight in the center for even psi on both sides. i live near milwaukee wi if anyone is wondering

I'm currently a college student majoring in Electrical Engineering. A few years back, I competed in roughly about two MECA competitions as a hobby. The experience was great, but short lived. With my new schedule, I'm able to juggle classes and a job. With that said, I've decided to go back into competing so that I can have something "fun" to do outside of studying hard during the week. I'm specifically looking to compete for SPL in MECA. What I buy from Fi will strictly be based off of the new point system for MECA. There are several classes, and I'd either like to compete in either Street 1 or Street 2. Street 3 is simply above my budget as a current college student. The…

I see a lot of people using the SSD to augment their existing home theaters all the time. Is there something that can be done to lower the FS? Maybe a different spider pack or gap adjustment. Thank you for your time and response, Chris

Looking for 2x BL with 3'rd magnet/HiXMax/dual 2ohm/flatwound/cooled/daily/non-universal/regular lead option group. I wouldn't think that adding magnets would be a bad thing...

Hey guys Im going to build a new box for my 18" Q. I have 6.7cu. ft. before disp. and port.. which I know is small, which is why I need to use aero's. Right now I have 4x 4"x10" aero ports. can someone give me recommendations. Do I need to get 6" ports?? I know for port area that 2 of these 4" aero's isnt enough, but I think if I go to 3, mine are to short... Can I use the flares, and use PVC pipe to make them longer??

Im going to try and be brief.. since I'm at work. (One of the very few sites I have access to!) I used WinISD to play with output numbers. Of those, I valued port velocity::frequency ratio. And I tried to configure a flat response bandwidth while keeping my desired tuniing @ 29hz. Quick specs: 1. Its a trunk build ( 4 door camry) 2. substage amp VFL 150.1 3. Rear firing design // 15" SP4 with electrical to boot. 306A - 274A alt (Hot). 306A Peak (cold) . 178A Hot @ idle I can post more details on Port volume later, I left the last dimension of port length at home. But what your seeing is port depth 17.25, height 15.5, length is somewhere between 26.xx to 28.xx. I cant …

alright so ive had my 12" bl and sundown saz 1500d in a 2 cuft box wired at 1 ohm for about a week now and its not as loud as i expected. its a great sub dont get me wrong but it really doesnt get loud unless i turn on my loudness control on my headunit to atleast low and turn my eq settings on super bass... but i thought i read somewhere that you should not do either of these things... i was checking out my box that i had custom built and the port area was only 3.5" x 4"... isnt this a little small? i thought the port area should be from 32-24 square inches since the box is 2 cuft. would this make my setup louder?

Rather then stay up until 3 in the morning for firechat due to time differences i though id ask here... Need a sub for my HT. Currently I have two BL's in my car. I want something that that plays lower with more depth then the BL's. I love low lows with presence. IB is not a option in my current place. What is my options and what options should I select? is there something else I should specify? Sealed ported whatever I can build the box and consider my self a bass-head intermediate but this whole HT thing has me baffled. I know Scott has his finger in other sub companies as well, which makes me think why Fi and not any of the other companies he has a part in? I ne…

i just ordered 2 12" Fi Q's and i've seen specs on how many cubic ft to make the enclosure and stuff like that but i want to know the specs on a ported enclosure for TWO 12" fi Q's!!! i just want the best for my twins and whats up with all this tuning to (x) amount of hertz and s*** like that?? how the f*** do u tune a subwoofer??????? well all i know is that i want my twins to play as hard as possible with the best sound quality and for people to be like WTF DO U HAVE IN UR FU**ing TRUNK MAN!!!??? lol feel me? so i just need 3 questions answered: specs on a ported box for TWO 12's.....whats the ideal hertz to tune the subs to (and how to do that).....and please list the…

i was playing my fi q 12 with bp power on a zx1500.1 in a 4th order bandpass bout 3.5 cubes all together and it was sounding good and knockin nicely when all the sudden it stopped no pop smell or anything. . i took the sub out an everything looks fawless but i tested the sub with a battery and a dmm and the ohm reading is all wierd i was just wondering if i can have this fixed or what ill send it in if i have to i just want my sub back. . . . Please help. Thanks, Teddy

Just made a topic so you don't have to scroll through pages to find it... Ok first things first. The test was done in my car with my equipment (in signature). The box is 4.5 cubic feet net tuned to 32 hz with 57.25 in^2 of port area. Subs: 15" Havoc and 15" Q with BP option (both have embedded tinsels) Yummy pics: Here are TermLab results... Outlaw style (at the kick, both windows open) Q: Havoc: Legal (sealed up at the dash) Q: Havoc: Listening experience: To tell you the truth, unless you are a freaking machine, I doubt you would be able to tell the difference between these two drivers under the exact same circumstances. Now everything I am saying is dealing wit…

I just did a re-cone for 2 BL 12's and it seems that the 2 re-cone 12's play harder and have alot more excursion now than the other 2 12's in my enclosure. Is this because they were re-coned or is there another problem? I had all the coils metered yesterday and the 2 re-coned subs coils read lower than the other 2. Would the lowere impedence make them play harder?

Do you need big power to make the BL series subs play at their best? Will they play low and deep on 1,000 watts?

where is the optimal placement for the sub cut out. i went a head and am building a box for my single 12"Q. and it's just a basic little 2.36cuft @ 31.69hzported box. i got to thinking before am going to make my cut out for the sub. should i put the sub closer to the port? or dead center? or away from the port? what are the advantages and disadvantages of each? and what would you recommend? also the sub cut out should be at 11.7 inches right? on the website i got that from the cut ID number. thanks guys

after reading tons of reviews and watching a ton of vids on you tube my 8 month journey has brought me to fi tomorrow im ordering 2 15'' q's..i will be sending around 2000-2500 watts in total..now i need some help please guys..id like some suggestions on what size box to go for both sealed and ported..because im not building my own box im having a shop do it for me so i cant just try a few boxes i dont have the funds to do that..90% of the music will be rap and the other 10% will be a mix of all other kinds of music..going 15's i obviously want it loud but id like it to be musical..have sq to them..im not just looking to sound like a fart canon or anything..i hope this in…

Ugh i just bought a box form a audio store and its a 1.75 cuft and and im sure if i want to use it. Would it be ok to use it tell i find out how to build my own box?

Im gonna get 2 12in BTLs and I was wondering if they could handle 3,000RMS or higher and not have to worry about it, and the sub would be a daily sub but fully loaded otherwise.

Alright first off sorry for so many topics about all the subs. Im just in the process of deciding and im all over the place lol. But i think i have narrowed it down to either 1 12" Bl with BP Power and Flatwind Coil or 1 15" Q with BP Power. Both will be ported. I will use the US Amps MD 1D (underrated 1200w @ 1 ohm). I drive a 2004 Ford F-150 and will be taking out one of my back seats so i have about 7cuft to work with. As of now i am leaning towards the Q because it is about $70 cheaper and because i also listen to not only rap but country alot... Just want to hear some thoughts and opinions. Thanks

wondering if I buy a couple MT motor's can FI help me out? [email protected]