Fi Technical

I am loving those FI x specs, and it has a strong BL as well I wonder why these didn't sell as good as the others.. It almost seems like its a good as a subwoofer as a ssd but cheaper. Im no expert but looking at teh specs it has a stonger bl. more efficient, lower fs Did we miss out on one hell of a woofer? or I know I did. IT has a nice xmax as well.

room wise im stripping everything out of the back of my car and starting again.. the box in there is 3.5CUft with displacment to give you an idea on how big it is, i need some ideas of port and sub postioning which way to face them, where to put them? and general box design also some advice on the actual sub will be using for : Daily use 2000RMS @30Hz so what options would be best for the sub? Vw lupo thank you

I was wondering if the BP option changes anything on the T/S parameters of any woofer it gets done to? Does it lower efficiency? And if it does, what is the point? Does a subs BL drop by having the BP option?

Just wanted to know what peoples thoughts are on the aq1200d amp.. how are they? will they hit hard with the 15" BL ? i heard their rms output is unnderated. but listed at 1200RMS at 1 ohm

I'm lookin to run a pair of Q 10s eventually but I'm just wondering if anyone has experience using them in a smallish sized ported enclosure? .7 cubic feet to be exact, 10 sq inches of ported, tuned to 30hz...per driver of course. Thanks in advance.

Could somebody tell me what the diameter of the magnet is on the 12" BTL. And, what is the mounting depth of the same sub is. And one more thing, if I build a box that is 5" at the top, 11" at the bottom, 20" tall, and 40" wide, will that be enough room to fit a 12" BTL with just cooling(will it be deep enough)?

Recently I built a box that is 47 x 22 x 22 with the port slot it all comes out to about 9.3 cubes, i was wondering if any of the gurus could tell me if that entirely too much volume for 1 18" bl daily driver?

Box is 13.5cuft Tune to 32hz After subs just under 13cuft Subs are in a common chamber one large vent this is a slot port what do you think about VENT inside area height 5 in Width 39 in depth 15.5 in This vent will be taking up 2cuft over all this numbers were made with carstereo.com calculator is this going to work good or do i need to rethink it again WILL TAKE ANY INFO

Is there like a list of subs that you guys can recone? or is it just american sizes? or what? Are there any rf's able to be reconed? or are they all foreign motors of some kind??<----T1's????? i want some ssd's soooooooooo bad but i need some $$$ and ive got 2 toasted T1's sittin here, jw wonderin if i can do anything with them instead of sending them to rf for $104 each plus shipping which is like $40 each, each way---- $400+ haha Thanks

I have an 18" btl in the mail it should be here tomorrow, I totaled my truck a few days ago that it was going to go in so now I have to put it in a 98 mitsubishi eclipse for a month or so i'm looking at making a box L34xH24xD17 wich I think is about 6.9ft cubed so I would need about 75 square inches of port. how do I tune it to 32hz?

I am about to purchase a single SSD 12" to pair with my Rockford Fosgate T1001-bdcp. The amp is 1 ohm stable, but the birth sheet shows only about 50 more watts when compared to 2 ohms. May I please ask whether you recommend going d1/serial to 2 ohms or d2/parallel to 1 ohm? I will be going with high QTS/sealed and cooling (personal preference). Thanks!

This is tuned to 36hz THIS is tuned to 32hz The 3 round ports are 6inch by 16.75L

Guys, I was wondering why some people go outside the recommended cubic feet from FI for enclosure size? I am thinking because its vehicle specific or is there another reason? I have seen guys running 4 BL 12's in a 13 cube net enclosure.

ok i have a 15" fi btl with a sundown audio saz2000d. i built a box (3/4 mdf) with 4.5cubes of air space after sub displacement. i have it tuned to 33hz,(slot port) it sounds pretty good, i think , loudest sub i have ever own lol... im just wondering if it wouldsound better if i seal off the port and add some round flared ports ?? any thougths ? ideas ? sorry for the stupid question... please sum help... should i leave my box alone ? build a new one ??

Hey i was wondering if you guys could recone a Rockford Fosgate HE? I cant find any recone kits.

Anyone know how to figure out the resonant freq of the 10" BL's? I know they are supposed to be 40.3 Hz, but I had Fi tighten the suspension to handle more power on burps. How do I figure out the correct resonant freq without spending $100 on the Dayton woofer tester program? I had them built with the SPL option and the flatwind coils if that makes any difference.

Optimal box internal volume is 1.1 after displacement, therefore, before displacement it would be 1.1 + .14 = 1.24 cubic feet. Would it be more advisable to buy a box that is slightly bigger than 1.24 and put something inside of it to displace volume or to buy a box slightly smaller and fill with polyfill? I'm finding boxes with 1.0 cubic feet and 1.5 and not sure which way to go.

In order to get a 1 ohm load out of the 2OHM DVC, I wire the two negative terminals together with speaker wire coming out of one of them, and both the positive terminals with speaker wire coming out of the same set that the negative came out of right?

you guys think a 10 cu ft box ported tuned anywhere from like 30-34 is alot? i was talking to a guy about him builing me a box casue i dont wanna get into making one. he said around 10 cu ft. tho its also going in the back of a suv. but do you guys think thats alot for just a single 18 bl running off a hifonics 2k watt.im not gonna be giving it to much probly arounf 1200 to 1600 its got pf chamber and cooling -thanks

i emailed Fi SIX months ago askin about gettin a recone, and well im still waitin for a reply. i think i sent a email to nick, but cant remember. who else can i get ahold of to get a recone?

this box is for a 12" bl and its gotta fit in my 99 acura el (honda civic sedan for you americans) my link let me know what you think.

iam having a prob with designing my port for my box can anyone give me some ideas on what to do i already used the speaker boxtunning calc but it didnt really help me

Are you guys able to recone a 10" TC OEM woofer. The surround had ripped completely from the center cone and i just want to have it fixed.

Hey guys girls just wondering before i tear the system outta my tahoe and redo it which box will be better....the current box is for 2 18" fully loaded BTLS...ea sub has 6cuft after displacement and tuned to 32hrtz...but would it be louder deeper etc if the box was 1 chamber tuned with both subs..kinda like steve meades...just wondering.....also running 300amp ho alt (soon to be 2) big 3 all 0 gauge 5 batteries 2 US AMP MD-3D 1 on ea sub....let me know if im forgetting anything thanks

I am on the verge building an 8 cube sealed box for a Fi Q18 which I will be buying in the next 2 weeks. I was set on everything until I came across one question. Do I need to have a 1 inch baffle? I plan on double baffle flush mounting. I was going to build is all from 3/4" MDF with a lot of internal bracing. No polyfill since I am maxing out the dimensions. My dimensions are: W:40" D:21" H:21" (will fit nicely in the spot of the room i picked ) Besides the baffle question, does anyone see any problems with my plans?