Fi Technical

I made this box not too long ago. Does it look fine to you guys?

i just ordered my SP4 18 today, i thought i had a box idea but i was told it was not very good so i need some help. back seat of a dodge ram 2500, i have 30HX36WX31D max space, smaller is better but thats what i have to work with. i intend to mount it on a new tool box im installing in place of the rear seat. if i use 2 .75" MDF sheets to make 1.5" panels and build the entire box of that do i need to double up on baffle? do i need bracing? i currently have a ZX2500.1 to power it (do you think i should upgrade?). i am not sure exactly where to tune it so i planned on starting with a high tune and an extra thick bottom and then extending the port and pulling parts of ht…

http://imgur.com/a/lNcLR#0 i have two sets of images its this album. a 33hz tune and a 36hz tune. i intend to build the entire box minus one side (leaving it to be held on by only screws) and change out the port as i test the subs volume. once i have things set ill glue on the final side. i would greatly appreciate it if someone would check my math and offer and criticism on what i have laid out here. thank you very much.

hey guys im new to the forum and i have a question. im thinking about ordering a dual 2ohm 15" and wiring it down. my only fear is having my amp go into protect mode. my amp goes into protect at .8 ohm. what do the sp4 15" dual 2 ohm coils actually read. are they actually dual 1.27's if their re: 1.27 Ohms/coil? even if i wired it down to .635 do you think i'd be okay after box rise? im going to build a daily driver tuned around 28-30hz 500 is a good chunk of change and it would suck if i had to wire it up http://store.ficaraudio.com/sp415/ thanks for your help guys

i just got my sub hooked up and my chasing electrical issues. while testing the sub i noticed the dust cap got very very warm, to the point of me wanting to pull my hand away when i touched it. the sub was not reaching xmax and was also not fully powered. i have the sub wired as follows to a ZX2500.1. now i noticed that the kicker amp flashes protect when the bass hits but its not constant. so i expected there to be a grounding issue. i ran all new 0ga power and ground using 5/8" brass bolts and nuts and 1/8" brass flat washers on a freshly grinded clean section of my frame rail. im replacing my alt wire to 0ga and am looking into a new alt. all this said i feel that th…

I've had this sub as my daily for only about 2 months and it finally feels like it's getting broken in. At the moment I have it on a hifonics brx2400 along with a kinetik hc600 (will be upgrading soon) 220 amp alt and runs of knukonceptz 0 gauge CCA (will be upgrading to OFC). Anyway my question is, why after bumping for about 30+ min does the dustcap progressively get warmer?? I had this problem before with some crappy RF p2's getting extremely warm on the cone right above the voice coil, but they were being pushed at full rms with good electrical. NOW i am pushing a 3k rms woofer with just a hifonics (probably 2000 watts) and poor electrical (for the time being). Ho…

i seem to recall either FI or a member on here stating to use a Bl or BTL cut sheet for the SP4. i am getting my recone soon and want to build a plane vanilla box tuned to recommended spec to see what it sounds like. what cut sheet should be used with the SP4?

Can we get a section pinned to this forum of the options and what they do with the sp4 and also enclosure recommendations

so I know you guys like a lot of details with having a picture on the problem but im not to a stage with a whole lot yet. But I was wanting to do two square ports on the lower corners of my box that i'm going to be making and the thing I was curious about was how to add up the separate ports on torres. if I wanted two 8x8 squares would that be what I put in and add the total length or would you put it in as one 16x16 since that is the combined port area

Guys I want to add a 4th SP4 to my current setup and was wondering if I have enough space in the cargo area of my SUV to do it. I have the following demensions...46W x 44D x 25H.....And how much port area to get them really going with about 16k of power?

Thinking about going with SP4 15 inch subs. Anyone can help with how many cubes I should build too and how many inches of port? Will be running them on about 6K of power. Thanks

Ive been looking into a sp4 18 and have a few questions, hoping to find somone on the fourms instead of flooding fi with emails atm. Would running a cresendo 3500 to a single 18 sp4 at .7 be to much? Also how many cubes should i go with with 1 18 on 3500 tuned to 32hz. I would be getting the sub with all the opitions also if that makes a differnce in power handling. Thanks guys!!

Did the guys at Fi re-evalutate the SP4 and change the RMS from 2500 to 3000 watts, or did they redesign it to increase RMS?

I have looked through pages and pages of forums and cant seem to find anything explaining what the purpose of the space spider on the sp4 is. could someone please help?! i ordered a sp4 yesterday with the space spider and would like to know its significance.

I own a BL and am buying an SP4. will this box design work perfectly for the SP4 and well enough for the BL? did i screw up on anything? at the bottom of my port i have bracing crossing it, will this be an issue? should the port be fully open down to the bottom of the box? i could not find any great info on port area for the SP4 so im sitting a bit over the 16 multiplier right now. i was thinking of adding a bit of that fluff to the box to make the sub feel it was in an enclosure closer to 8 cubic; is this a good idea? im going for SQ at high volume, or at least as much SQ as the SP4 can give me. what should i change, all opinions welcome. thank you. http://imgur.…

Ordered an SP4 15. I'm designing my box and would like some opinions on lower tuning, 25-28ish hertz.I'll be running a crescendo bc3500. I know the "norm" is to have port tunng a bit higher, and my current sub is tuned to 32 (SSD 15) I was hoping to get some thoughts

what is the speaker wire gauge for a Fi BTL?

So I got a 12" Q last week and I LOVE it but my sub cuts out or has alot of background noise and i hooked it directly up to the amp and it plays fine and I am figuring that its the speaker terminal because when i put my finger on the negative it starts to play but when I take my finger off it stops? and In addition the - wire looks charred on the inside connecting to the terminal so my main question is has anyone else had this problem and what would be a good solution?

i was wondering how much a 12btl, 15btl, and a 15Q weighed thanks in advance

what gauge speaker wire would be recommended for 4 10" fi bl (flat wind coil, cooling) i have 12 gauge speaker wire but im thinking that that is too small. its kicker shielded wire. would i be able to tie the 2 wires together and double them up to have roughly 8 gauge wire? or is the 12 going to be enough?

I am currently waiting on my q12 dual 2 to arrive, and it is going in my work van (E-150) Passenger Converted to cargo. I have a two fold question I would like it if the box were no more then 15" front to back considering the sub facing front. My current setup has the sub firing into the back of the drivers seat as this is where it is the most protected and less likely to be damaged. I wouldn't mind using the ported box cutsheet for a Q12 as shown but I would have to put legs on the "face" and set it up so it was downfiring at the floor in order be able to carry the amount of tools/cabinets I typically do. (I am a cabinet maker so I can build anything you can imagine …

Does anyone have the specifications for the last model of the Q 18? I no longer have my saved WinISD profile, so that would work as well. Thanks!

I was wondering if you guys had the specs on the btl 15" fully loaded. Specifically the displacement after the 3rd mag', mounting depth, and xmax. I ran a search but no luck. How do I calculate these specs if I want to double the front baffle board. what are they afterwards. thanks for the help in advance.

specs on 09 fi ssd 18

Curious specificaly on the ''Q'' 18 w/bp