Fi Technical

im looking at using the ib3, and was wondering if there are any technicalities that i would need to take into consideration before doing it in my car. i would place the baffle behind my rear seat, and seal everything off w/ fiberglass where it goes under the rear deck and between the wheel wells/strut towers. anything else to take into consideration?

I was wondering if this box would be big enough for two 15" fi btls. The box is 38 length X 25 width X 23 height. After displacemnt of everything its around 7.5 cubes at 31hz. The port is 6 wide and 25.5 long. It would be for daily use and each ran a sundown 3000d. thanks for the help

i currently have a crossfire vr 2000d and an optima yellow top with a kinetik hc600. running 0 ga from the battery then 2 ga from the kinetik to the amp. im currenty upgrading the "big 3" and am looking at an alternator around 200 amps or so. is that enough upgrade to feed that amp? the type of subs i was looking at are the FI BL15's which are 1000w rms and also the RE AUDIO sx15's which are rated the same. also if anyone would recommend an enclosure not only for daily but for comp. as well....probably somewhere along interchangeable ports

What sort of rules apply when constructing a ported enclosure. I know the basics like tuning and port dimensions. But do subs need to be spaced a certain distance appart to be effective...? Things like that! Cheers

Hello I'm new to this forum as i have just purchased a used Q18 " sub and i want to get the best from the sub for my suburban, i listen to rock and rap and i want to make a ported sub enclosure for it, sub up port back. my question first is could anyone help me design a enclosure with the best tuning for all around use? i love the lows but i would like it to not only go low but have a punchy bass aswell. if anyone could help a Fi newb with this it would be much apreciated. thank's i'll give specs of the area i have to work with, 47w 24d 22h ,99 suburban using a fosgate t5002 pushing aproximatly 800 watts, my goals are just a daily driver setup with good sound quality. an…

Im currently using the RE Enclosure calculator (http://www.reaudio.com/speaker_box/LPort_Box_Calc.html) and after putting in the dimensions I can fit in my trunk and Im playing around with port size and what not and I was curious, the "tech" section on the Fi site says the recommended tuning is 33hz, I can only get my box to fit if I tune it around 34hz, is this an issue? would it be better to be lower than ideal if you cant get the ideal 33hz like 32hz instead... Or am I not even gonna notice? Also, again refering to the "tech" section, for the 10s it recommends 15 square inches of vent per cubic foot of air space, is it a major issue if I can only work around 12 square …

Hey I'm going to buy 2, 12" BL's and I was wondering what amp you guys would recommend to get the most out of these subs...

I have 2 15Q (1st gen with no options) with 2 saz1500d and it gets hot over a short period of heavy bass music. I was wondering is there any way I can increase the power handling of the sub. I am not from the US so to ship the motor over to get the partial BP would be expensive. would it be possible to use the BTL spider on the Q or other options? I know changing the spider would increase Fs and Qts but would it be significant? thanks

scott, been sending some email this past few days, did'nt get any reply is everything ok? pls. check your email...thank you

Will the new sundown sae 1200 coming out in november be too much for a 15Q loaded?

is my rockford fosgate t20001bd at a 2 ohm load too much for my 2 q18 d2's? its a 2 ohm load at 1600wrms. thanks!

Before my son was born, I was running 18's and I really miss the output of that setup. So I am thinking of sending in my 12's to get re-coned as 18's, or if its not to hard, just doing the re-cone myself. Yes, I am tempted to off load the two 12"s and just get a 18' xcon or BTL, but with hardly any more power, and 1/2 the cone area, this setup should be louder theoretically. Secondly, I am not a box designer at all and I am completely lost as to what works and doesn't. This is a daily setup. I don't compete. Using RE's Calculator just as a ref, it looks like the max volume I am able to get is around 13.5 cubes before displacement. That is leaving a bit of space between…

I have a pair of 10" BL's. I'm running these with an MA Audio HK4000D, I've been running it at 2 ohms so they'd get about 1900 watts each. I'm planning to drop the ohm load to .5 and send them more power, at least 2500 watts each. What would the recommended enclosure size be for this increased power? I'll figure out the ports and such after but I want to know what size enclosure would be right for that amount of power.

assuming both had the BP option and would be fed by a 2200 w rms amp, what kind kind of difference would i notice musically between the subs?

I will soon be purchasing the Fi BL and was wondering if I will have to upgrade my electrical. The amp I will be using is either a sundown 1200d or audioque 1200d. Thanks

does flat wind coil and bp power add to a 12" ssd? how about bp power on a 12" Q? just thinking about future upgrades. thanks.

I have two fi q 15 w/bp power that I need to ship in for recones. could you please send me the info that I need to go about doing this? do I pay before or after they have been fixed? thanks

12" BL D2 Daily Flatwind Cooling @ ~1200RMS. 2.25cuft @ 32Hz. Just wondering what the subsonic filter is recommended to be set at. Right now it hits all the lows with ease when set at ~25Hz. (Soundstream TRX1500D)

do u guys have a list or catalogue? I hate asking for each individual part... I feel like im always hastling uguys here for recone parts either way need some dvc 1.4 and 0.7 alum coils, cones, spiders, tinsel(the thick stuff) and some dust caps do u prefer an email with a list?

ill be ordering the 12" ssd's soon and temporarily they will be going in a prefab (i hate prefab) dual twelve box with the port in the middle. 2cuft per woofer. when i put my other woofers in there they were loud as f**k but when i played a song like bass mechanik moonstone that has a 20hz bassline they bottomed out and almost broke the voice coil. heres my dilemma i have been seing a lot of people use the boxes that are similar to the box i have exept the port isnt in the middle of the woofers its on the side.ex: http://subwoofertools.com/forum/ported-box...mp;Fs=&CE=0 all of the vids ive seen they either burp the woofers or they play some crap from jeezy, never any…

I am looking for sound quality mostly, not worried about if the bass rattles my car apart. If I go sealed would it be terrible if I went prefab from online? and if I went ported I am thinkin about 2 cubes at 30 or 32 hz. how big of a difference would trupan-lite over mdf make? thanks all

This is the graph i got from WinISD volume is 5.4 port is 4* 8 * 11 (dont know if thats the right port size or not. I would like it tuned around 32Hz) http://i235.photobucket.com/albums/ee29/mld42/FiBL.jpg This is a very rough sketch of the box to show where the ports could go. The sub with be mounted inverted for more box volume. I have 2 12's now in a sealed box, but would like something louder, and I have a BL 18 dual 2 that im not using so I am trying to fit it in my truck. http://i235.photobucket.com/albums/ee29/mld42/Blbox.jpg And is there any way to extend the port out of the box rather than porting the inside. I havnt seen this done so I dont know if it wil…

i know fi doesn't make the xxx, but the model i have was designed by scott so I'm assuming this is the appropiate place. i searched archive.org -> reaudio.com and came up with no results for the 03 model. anyone still have the 03 xxx 12 t/s sheet by chance?

does anyone have a cut sheet like the ones posted but with 2 18 btls Thanks in advance

This is my current box plans for the 1 18"BTL and 1 Saz-3000d I have. I plan on putting all these into a 03 Tiburon(hatch) and competing in spl. Really my only question is would a bigger box better/ is 5.27 cubic feet enough. Thanks box: (outer dimensions) heighth = 16.5 width = 36 depth = 21.5 port: (inner dimensions) heighth = 5 width = 7 length = 10 this port will tune the box to about 34.67 hz which is what i personally like to tune mine to. after port displacement...this will give you about 5.27 cubes of air. so you have room to brace it and not go below the recommended volume. this is also assuming that you're using 3/4 MDF. competition port: (inner dimensions) he…