Subwoofers / Speakers

I have a fi btl d2 12 ufo style and cant seem to find another one. My question is can i order a newer series fi btl d2 to go along with my old one and won't have a problem? Thanks

Hi, just wanted to know if the IXL-10 2.2 would live well with a US acoustics USB2150 wired at 4ohms Here are the specs for the amp: 2 x 150 @ 4ohms at 12.9 volts 2 x 225 @ 2ohms at 12.9 volts 1 x 450 @ 4ohms bridged at 12.9 volts THD less than 0.01% Frequency Response: 10Hz-30kHZ, -0.5 dB Input Sensitivity: 100 mV - 8.0 Volt Crossover range Low Pass: 40 - 460 Hz High Pass: 65 - 4.5 KHz S/N Ratio: 103 dB Channel Separation: 90 dB Damping Factor at 20 Hz: 95 Reverse Polarity, Thermal, Short Circuit, and DC protection. It would be installed in the driver's side hole inside the trunk in a stealth-like box. The reason i'm loo…

I am Neal Tyson, head of Team Neal Tyson and I hope to be able to help you with all your audio needs.

Sorry it`s a JBL sub - But I do not have any MAG 12" Yet... Anyway this will give you a good idea of what an ISO set up does. The following text is taken from my Forum: -------------------------------------------------------------------------------------------------------------------------- O.K. Get ready because you are about to see one of the worse looking installs ever. I`ve not bothered doing anything special because my boot space is regularly taken up with power tools / tools / bags of sand etc. So there you go. No point in having a nice looking install that will get messed up within a few weeks. Anyway what I did today whilst at work was... ...add another 12" JB…

ok, i am getting a new 15" (when they send these bad boys out). but i want to make a small sealed box, close to 2 cf. This is going to be put into a Saab 9000 hatchback. Also i have viped d1200.1. I have two box ideas, 1 is just a rectangle, and the other is a wedge design, witht the woofer facing somewhat at an angle. also i overhan the long peices over the sides. which one would sound better in my car?

I have a 1994 GMC Jimmy 4-door. I am looking to replace my factory speakers. I have 4x6 speakers in the dash (not sure of mounting depth, could not find that spec. anywhere) and according to my research 6 3/4" in the rear doors (again not sure of mounting depth). This will be the first time i go with components or run the speakers off of anything but the head unit. I will be using an old rockford 2 channel amp to power the speakers, it is 100.2 (if memory serves). I need help choosing speakers to fit in the stock location. I would like to keep the cost ~$200, but i can go more if need be. I am open to all suggestions since i am a noob when it comes to this. So an…

Current Equip HEAD UNIT Kenwood KDC X695 AMPS: Alpine MRP 500 Focal FP 4.75 SUB: Sundown SA-8 v1? WIRING 4 Gauge Kit from Audison I drive a Lada Niva which is essentially a russian jeep. Its about the same size as my wifes civic hatchback only taller. I am currently making a box using the design i got from Ryan @ RAM designs. The speakers that came with the car are a joke. Boxed 6x9's inb the rear which sound terrible and some bargain JL 5-1/4's in the front. I listen to a variety of music ranging from metal, dubstep, hip hop. I would like the speakers to have crisp clean highs but still have some decent mid range. (my old MB Quarts were great for highs but gutless in th…

I would have clicked the buy it now but..... those have the old school rubber surrounds that are most likely somewhat dry rotted. These would be better off kept in the box the way they are. I would LOVE to put these in my 91 Acura for a somewhat period correct system but these are just too damn sexy! http://cgi.ebay.com/ws/eBayISAPI.dll?ViewI...I:IT&ih=006

I was thinking about putting three 10" subs in my '91 Vette, so I posted an earlier thread asking for suggestions and a few people suggested that I run just one 12" sub instead. Personally, I think three 10's would fit nicely, sound better and get louder than just one 12, but I'd like to know what everyone else thinks about it. The maximum dimentions I have to work with are 34" x 12 1/2" x 18". Thanks for any input.

If a 12" needs 1.75 cubes and has a displacement of .12, does the same model 10" need 1.4 and has a displacement of .096? Do you multiply 1.75 & .12 by .2 because there is a 20% size increase from 10 to 12?

Well for the MAG is going to be going into the 3rd box in 3 weeks.....mistakes on my part....I am deadly with a tape measure!! it is in 1.1 cubes sealed right now....but i am going back to ported...output suffered too much for me So i took measurements like 3 times to make sure it will fit....the box is going to be 34L x 15H x 10D which equals 2.18 cubic feet......as you can see i want this box to be as thin as possible cause i want to save as much trunk space as possible So going by those measurements and then add in the port and driver displaement.....port is 13.5 tall by 1.5 wide and 24 inches long which equals .28 cubes so after all displacements i am guessing it will…

Hello everyone. I was wondering if anyone out there could help me find a manufaturer that can rebuild a subwoofer based off an Audiomobile Mass series magnet structure. It is a 3inch underhung design that was origonally built or at least designed by TC Sounds. The design was also used in the SVS Ultra(v1) home subwoofer. TC as some of you may know has been restructured and are far to busy to handle this request. I was just wondering if there are any other products/manufaturers that would be compatible. Any input is welcome. Thanks.

What is the displacement of this sub? I heard .40 cubes others are saying .15

Im looking for a good 6.5 component set that is under $300 dollars and has good midbass. dont have an amp now i will get one that will match up good with the components.

k im preparing to do a sound competition i had a custom box built for4 kicker l5's, but the company i ordered my subs from accidently sent me 2 l7's and 2 l5's will that mess up my system by running 2 of each i will b running 2 1000 watt amps both at 1 ohmso 2 subs to each

will they ever be Components again? jamie

I've been looking for a good setup, but very confused about what I'm looking for. After reading a lot of forums I found that a lot of people are suggesting the tangbands and fountek's. I looked at some website and found these speakers. Wanted to know if this would be a good setup or not.... Tang Band W6-1721 Tang Band W5-704D Tang Band 25-1166SJ Each door will have 1 W6-1721, 2 W5-704D, and 1 25-1166SJ. Any feedback would be great.

In case some of you haven't seen it, decided to post my video of the magnum d2 12's...they wang. Oh, yes...i sold them cause i am a complete dumbass...i hate myself...i want them back. http://www.realmofexcursion.com/videos/Sou...magnum12.1a.wmv Box in video: 7.2 cubes net @54hz, 160 sq. in. of port! Two avionixx 1200.2 amplfiers. Oh, and yes...i did say 22hz in the video...and remember the tuning above! Few pics: Some of you may hav already seen this on caraudio.coma while ago...but figured i'd post it in the SI forum. peace NG

4 of my 15" recones, next to my friends 18" mt since im reconing all my mts, we blew all 4. in the process, this basket broke off the motor the voice coils. the one that is un wound came off the motor with the broken basket lol. we pushed that bitch hard..... baskets and last but not least, the motors

alright I've been asking alot about differant subs and I'm sorry to bother everyone with it just trying to get info before building for next year. so as the ? says how is the AQ stuff and where can I find specs for them? Do they have a site and or a contact #? thanks

ok so i have a JBL GTO601.1II sub amp and an RF HE2 15 looking for a better sub. any suggestions? considering the SSA Icon15D2

I have been trying to wire up my subs. I have two Mach 5 Audio SPL12s hooked to a Audiopipe AP3000.1D. I am using 8 gauge wire to go from the amp to the subs. However I cannot get the wire to stay in these terminals. I put one 8 gauge wire in and tightened them all the way up and the wire still didn't really stay in there. So what I came up with is this: I took the nut off where the tinsel lead goes to the terminal, then put a length of 8 gauge with a ring connector on it. Will this cause any problems? I don't have both subs done yet, so it is not hard to revert. I find these terminals a pain in the ass! its sort of like what DD has done with their subs.

they are only 4" mids, but they have the sweet crossover and they are 1/4th the list price, maybe I could grab 2 pair, lookie >>> http://www.cardomain.com/item/MBQPSC210

i am looking for someone withe the specs for 2 18s to be placed in a 2001 tahoe or if a box builder has already made a fit box email me at [email protected] or hotmail.com thank you P.S Fi has differnt speakers which one is best for the sound and what is the rms range for 2 18s for Fi