Subwoofers / Speakers

So according to 12volt subwoofer wiring diagram I can wire two 2ohm DVC subwoofers to either 0.5 ohm OR 2ohm I can also wire only ONE of those subwoofers to 1ohm My question is, if I want to stick to 1ohm using those two 2ohm DVC subwoofers Can I just wire EACH sub to 1ohm, then run them to the amp each SEPARATELY from each other so that I keep 1ohm resistance? I have a Sundown 2000D

I have had my cut out cones sitting outside since last year, out in the rain snow and sun, and the only thing that has happened to them is the cones on a few have turned white. The paper cones are still solid, foam surrounds are all good, glue holding them turned white but not loose one bit. The coils havent rusted, the coil glue hasnt let loose... they are just the same as when I cut them off other than bleeched. I have been impressed every time I look at them, so the other day I was having fun and displayed them on my porch. It stormed hard last night so I went out into the dumping rain and snapped some pics. I think drivers have come a long way over the years, as ever…

What do you guys think would be louder(To the ear)? A 12" Havoc 1.7^3 tuned to 33hz Ported or A 15" Havoc 1.7^3(or more) Sealed? Each with 1000 Watts RMS.

i was just wanting some other peoples opinions on the subs i have. i have 2 memphis mojo 10s. a couple people i talked to, said that they arent that great. just wanting to see what other people thought

I have an old RF punch from sometime in the 90s. I tried googling about a recone but couldn't find anything. The surround is completely gone on the woofer. I don't remember the model number, I'll take some pics of it when I get home. But everything else about the sub is fine. It's a 10 inch and I had two of them in a custom box. The other one has a broken voice coil which I'm not worried about cause it's more work. I'm curious though if anyone knows where i can get a recone for the sub.

I have got two Precision Power 10" Flat Piston subs at 400W rms each. Recommended box type? How about for a single 10"? They're going in a honda civic trunk.

Hey I saw a breif post on Sounddomain forums but it was taken off because it was info on some new TC sounds subs that are coming out.... does anyone have any info on these subs..?

I currently have a ssd15 in about a 4cuft box with an 8" sonotube port... the port i believe is causing unloading problems because it is so long it is basicaly resting o. The motor of the sub. So would one 6" pvc port be big enough? Ill flare the ends either making fiberglass flares or heating the pvc up annd forming it around a dog water bowl. But please... im getting slightly aggrivated...

okay, this is going to be a shot in the dark.a guy came up from Louisville, to a local car audio competition here in Evansville. He was in the sound quality portion. he drives a mitsubishi montero. he said he owns a shop down in louisville. anyway, he let me listen to use front of components and I was extremely amazed at how well they sound. he said they were made by guy in georgia. he told me their name, but I can't remember for the life of me what it was. I believe it was audio something. I know this is an extreme shot in the dark but, can anyone help me figure out what these are? they hadreally nice midbass, they sounded amazing. I got here frank sinatra song, and then…

I installed 2 MB QUART 6" speakers 6 months ago in my front doors. I rescently heard a cracking noise coming from one of the front speakers in my integra (Left Door). When I removed the door panel the speaker stopped playing but if I apply a little pressure to the cone with my finger it starts plaing once more. Is it possible that the coils are faulty or is it something else.

Hi I am running two Zed audio Miniliths to one level 3 12 with the spl coils. I thought it would maybe be too much power but they take it very well. I have the sub woofer in a very small sealed box and it still hits very well and the frequencies are very pronounced. I would almost be willing to say it sound like 2 12s but it is not that loud. The cone has some awesome xmax

it looks like there was barely any glue on there to begin with i'll fix'er up here later today. but none the less

I have a audio pipe amp 1300 amp rated at 300W RMS@4 Ohm (<1% Distortion) 600W RMS@2 Ohm (<1% Distortion) 1000W RMS@1 Ohm (<1% Distortion) and a sealed box for a 12" woofer at about 0.9 volume What sub would you guys purchase under 200$$ Link tp my build

lvl4 18" with lvl 5 coil http://www.youtube.com/watch?v=xXtzQCCzTSw http://www.youtube.com/watch?v=Ug3RnLiGn-U

hi, i am thinking of using kick pods for my componots since they are too deep for my stock location ( they are re audio xxx comonopots) and i am wondering i was thinking of putt ing in some midbass drivers in the stock location in the door. know will that affect anything since there will only belike 4 inches seperating the componots and the midbass drivers.

I need a box for a Fi BL 12 sub woofer I would rather buy one unless it exceeds around $150. I would like it to be ported but I'm not sure if it will fit in my truck. I have a 2000 ford ranger XLT and I want to keep one back seat so it can't be to big. Any suggestions on pre-made boxes or if it's truly worth it, where can I learn how to build a perftect box for the BL 12.

Will 500rms make a Fi 15 bl sound good?

Hope someone can help, looking to buy 2 x 15in mags for my VW Golf Mk4, will look to have them in a sealed box, does anyone know if i will be able to fit them in with some room for amps ? :ph34r:

I got the CDT's 62 comps and one of the woofers has some tinsel lead slap. I was going to put some small feltish sort of pads on there to prevent this. Do you think it would affect the woofer to the point where it would change the drivers ability to to play?

ok ive got a rf t10001bd that does 1633 watts rms at 1 oh and 1110 at 2 ohm. i also have a 2.5 cubic ft per side ported box tuned to 35-38 hz. the subs i have now are rf's t112d4. one of them blew for supposively no aparent reason at all so i replaced it. now the other one blew and yet again no reason. so i was thinking of switching brands. i have heard about the fi's, and just wondering what ones to really look at. i was thinkin the bl or the q series. im mostly spl but want it to sound good too. and if i do end up getting some, what ohm load should i get? and how would i wire them to 1ohm or above? Thanks.

I am still up in the air about what i want to do with the limited amount of space i have available in my car. i remeasured everything and i realistically have about 3.5 cu ft gross to work with. I am pretty decided on building a nice baffle and facing into the cabin with subs. not sure if i should port forward or into the factory 6x9 openings in the rear deck. If i port forward, i am not sure if i should go with aeros or slot it. if i did it through the rear deck i guess that i would have to do aero ports. As for subs, i can either go dual 10" or 1 12, maybe 2 12"'s if they are lower Qts. This is a temporary install as well, but i need it to be somewhat decent. So i gues…

How should i build a box. Car is 03 crown vic. Subs up port back. subs up port up. subs back port back.

Whats the price for 2 lvl4 18"s with level 5 coils? dual2's

How are the alpine type s 6 1/2 components?

Going to build a small sealed box with a 12" sub powered with my Sundown SAE1200. More for sound quality than spl. Been looking at these two. SSA DCON 12 and Sundown SA-12. Will the DCON hold up when driven with 600w ? I think it's rated for 300. Anyone have experiance with either of these? It looks like the Icon 12 would be a better match for this amp, but it is priced a bit higher. Let me know your opinion.