Subwoofers / Speakers

I have a 09 Silverado and I'm thinking about getting something like a console custom built so I can mount my iPad in it. I always have my iPad connected to my radio and I think it will look much cleaner mounted.. but anyway I want to have a set of components installed I'm the console also. how do you guys think it would should and will it be a waste of money to do so? these are the component sets that's I'm most interested in alpine type r sundown sa series comps incriminator audio comps

Ok guys i know that in my previous threads i said i was going with the xcon 12 but dunds are a littke tighter than before so but i could still get the xcon but it would be a little longer of a wait so my question is on 1000 watts which would be louder in a 2.5cft box tuned to 33 hertz

I have 2 10" older RE SE with the 12 spoke baskets and will be building 2 sealed boxes for them. Its going in a 300zx twin turbo and so i want one in each corner. (I know one box is easier and better but i need room for t tops etc.) wondering if the enclosure recommendations of .4 compact and .65 optimal for the new ones would be a decent guideline or if anyone knows the recommended specs for these models.

after wanting a nice pair of subwoofers for a while i decided to go with some fi bl's but im not sure with what options to get them. do they come with woven tinsel leads ? im going to install them in a 97 silverado taking the back seats out i want to put 2 18's. i already have the amp and is a kx 2500 thats the reason im going with bls and not btls. i usually listen to hip hop reggaeton and country and im not going to compete just love loud loud shaking music

Anyone on these boards live near either Austin, TX or DFW, TX make boxes? I'm gonna need a ported box made and don't have time to make one. I'll pay well

Guys I know just enough to get into trouble and looking for some advise. I've got 2 Fi btl n2 15's that are going to be sealed off from the trunk with a blow thru in the rear deck. Each sub is going to be ran at 1ohm with a Rockford t1500-bdcp amp. I've got 4 sets of Rockford T3 6.5" components and plan on running one set on each channel of my Rockford t800-4bdcp. My question is this..what freq should I cut the subs off at..where should my components pick up at..and are my components enough? Will they be loud enough? Will they go low enough? Thanks for any help you can offer.

I decided to temporarily put in one of my SE12's in at 2ohms on my T3002 in mono mode. Giving it approx. 800 watts. The box is 2 cubes after all displacement. For the port I doulble up a pc of 3/4" MDF and glued a pc of 4" pvc pipe through 1 layer and router a 1/2" radius on the top layer to make a homemade aeroport. The length overall of this port is 13". I don't believe I am right in thinking the tuning is at 32. Can someone double check me on this. Also am thinking about shortening the lenght of the port to get about a 35 hz tuning. This is just a temporary daily box for me to have something till it warms up. But I listen to all kinds of music so I needed some…

So i have 2 of the old orange basket mojo motors and im trying to find a place i can get some three bolt style baskets to fit them and recones to rebuild them and run about 1750w a piece on them. Any ideas where i could find some parts?

Would a RE SX 15" do well in a 2.0-2.5ft^3 Ported Enclosure tuned at like 33-35Hz, how would it sound, good or bad? RE recommends 3ft^3 as compact, but I've read on Tempro that a guy had 4 RE SX 12" in 1.25ft^3 each ported and he said it was very loud and sounded good, so what do you guys think?

Hello all. While at first this will certainly seem to be just another "what sub is better" thread, I am indeed seeking the advice of those familar with the possibility spelled out in the thread title. My goals are: 1). Sound quality for multiple genres. 2). Lowest possible frequency response, whether ported and tuned low or sealed in a large dual chamber enclosure. 3). Adequate SPL, albeit valued below sound quality. 4). Would a single 1000 watt subwoofer circumvent and/or surpass the supposed goals of dual 500 watt subwoofers, or would the contrary do so? I have been considering the 15" Icon, as well as the 15" IDmax for a single subwoofer application. As for the dual …

im looking to get a new component speaker set to go in my s-10 they will be the only speakers i have in there so im looking for the best bang for the buck i dont wanna spend more than 230ish so i was just gonna see what u guys think i should get or look into any help would be greatly appriciated

Hello. Can't find any specs of them. Can some one pour some light please. Thank you.

sorry double post

Its come the time to glass some kicks and a pillar pods for the truck. so far im leaning toward the 6.5" MB Quart Premium comps for the kicks and 4" Premium comps also. im open for suggestions i want matching sets so top and bottom looks even. tweeter does not have to match woofer though. just as long as both sets look the same Any opinions/ experience/ suggestions would be appreciated

I'll probably get flamed for this question, but here goes. I'll be purchasing a new sub in July and am having some trouble making a decision. I had originally planned on using the current box I have (1.21 cubes sealed) and getting either a SA-12 or Level 3 12" (the cutout is only 11" and those two are about the only ones I've found that will fit). But I've been doing some thinking about it and have come up with another idea. Getting a cheaper sub like a 10" DCON or a SA-8, and getting a really nice ported box built for it (I'm thinking Argent Audio). I'd love to do a IA 187, but I don't know enought about what I'm doing to put 600 watts on a 300 watt sub. Either …