Fisher Customs

Hello, I'm not sure if you remember me but I e-mailed you guys a few weeks ago about a box for two 10w6v2's, well I sold those and will get a 13w6v2, I'm hoping you guys can just build a simple sealed box for me. I sent you guys the 25$ for the design and I am waiting for a reply. What do I do now? I emailed chris(at)fishercustoms(dot)com, just waiting for a reply. Is there anything else I should do? Did I do everything correctly?

Very simple sealed box here, wanted to post the pics up for the customer.

Dont recall the driver, but this is a pretty standard slot ported enclosure. Double flush mount baffle, and will be finished off with black carpet.

I have 2 dual 12" Alpine Type R's...I've been told that ported is the way to go for these subs. There is a problem though. My trunk is small as well as the trunk opening. Right now I have a crappy sealed box 38"W x 10" TD 14" BD x 14" H...it has two old MTX subs in it right now. It was a pain to get in because the height of my trunk opening is 14" as well and the width is 35". I've made a few designs in photoshop but I'm not sure if they'd work due to my lack of knowledge in this area: I'm not sure how many cubic feet will be needed but I'd like the width to be around 30" and the height to be less than 14". Again...these are just some ideas...not sure if they'd work...…

Center located port, double baffle on the front. Pretty straight forward. Customer wants white port and black carpet. Should look nice when complete.

Not sure if those are the exact specs, just going by memory on this one. Pretty straight forward box here, with a 8* angle on the front panel. Will be finished off with carpet.

This is a 3.0 @ 32 hz enclosure for a single 15" Fi BL. Crx style, with a double baffle. The box will be left bare. All that is left to do, is sand it up, and the badge and terminals, and then get it ready for ship.

Hi i know this is perhaps a little off topic but was thinking when you use fibreglass or carbon fibre as detailing on a box(around the port area and front pannel) will this stick to the wood or will this cause some nasty rattle or something? if this is possible what would be the trick behind it? thx

well bj inspired me, i want to build my own box just to see how it comes out im good with my hands so i think i can do it. i just want to know what kind of glue and screws to use for the build? Tell me your thoughts thanks a lot in advance Billy

This enclosure is for a pair of 12" SI Mag V4's. Customer wanted to go sealed, and make it very sexy. Between the customer and Dylan, I think they did a fantastic job. This might be one of the coolest projects I have ever done. Should not only sound great, but also should be very, very appealing to the eye when we are all finished Enough of my rambling, here are the pics from tonight.

This is a nice little 1.0 cube sealed enclosure after displacement for a single 12" Mag v4 I believe. It will be finished off with carpet, once I get the compressor back up and running. Here are a few pics.

I believe this is for a single 15" Nightshade. Will be finished off in black carpet.

Dont recall the driver for this enclosure, but it will be finished off in black carpet.

Have you made an enclosure for the crew cab titan? Im doing a seat raise which gives me roughly 11.5-12" of clearance from the front of the seat to the floor, and 8" in the rear. I want to fit a beefy 10" like the Adire Brahma, or RE SX or FI BL.....do you know if I will be able to manage this? I wanna do a ported box for 1 10" sub.

This will be the enclosure offered with the package deal. I will get some shots of the drivers installed in this once I get it all completed. Box is 4.25 cubes @ 32 hz. Standard slot port, double baffle and charcoal carpet, on this one.

This box will feature a flared port, and a top mount double baffle. I believe it is for a pair of Type R's. Will be finished off with charcoal carpet.

This one will be 2.2 cubes @ 32 hz I believe. The customer sent me his own design. Will be finished with medium gray carpet. Pretty straight forward build here...

Title has the specs. Will have a center located port, which will be painted red. Will get finished off in black carpet tomorrow.

I have the design, the dimensions and everything. I just need it built and shipped. Need to know pricing info and other details if possible. Thanks.

Where do i go to place my order???

Got an enclosure for a single 18" Fi BL. 5 cubes @ 30 hz. Also, the customer wanted a plexiglass window installed on the front panel, and the driver top firing. Onto the pics...

This box is going to be so kickass. dylan is awesome at designing this thing, i wont post the rough pics unless he says its alright, but I'd be interested when this bad boy is built, to see a build log of it! Thanks BJ and dylan for all the time and work you've already put in!

I know you list prices but I would like it slightly custom. I am planning on buying a Mag v4 when they come out and want a box for it but I absolutely suck at building them. The Mag v4 has .07 cubes of displacement. How much would it cost for a slightly custom 1.07 cube net, 1.0 cube after displacement box with carpeting and 2 sets of terminal each wired up so I can directly connect to each voice coil on the Mag v4?

This box will be orientated a little differently than normal in his trunk. Port will be firing sideways.

I just ordered a Fully Loaded Fi BL 12 to put in the trunk of my 06 mustang. I have been looking at your builds and really like them. I was wondering how much it would cost for a box around 2-2.3 cubic feet tuned to 32~35 hz? Also, I would like to kinda customize it with an Fi logo. But thats not as important as gettin the best possible box. Thanks