shizzzon

Well, it SHOULD be wired that way regardless.... If it will solve your problem, we'll see. This is why- Stereo output section #1- Chan 1= Left Chan 2= Right Stereo output section #2- Chan 3= Left Chan 4= Right Left out on bass amp needs to go to both LEFTS on 4chan amp which is Chan 1,3 Right out on bass amp needs to go to both RIGHTS on 4chan amp which is Chan 2,4 Running Left out on chan 1,2 and Right out on chan 3,4 would be like running only 2 rcas to the 4chan amp instead of 4.... Of course u are still y-splitting the signal by wiring it the way i said, but at least the Left will be left and the Right will be right instead of left being the whole output side of Section 1 and right being the whole output side of Section 2. That would be like running 2 Channel Mono on a 4 channel amp.

Ah... maybe u might not have it wired right. so u have a left out, right out You need chan 1, 2, 3, 4 in so u need y splitters. Do the following- Y split Left out Y Split Right out Pay REAL CLOSE attention here- On 4 channel amp- Chan 1 and 3 are connected with LEFT OUT from bass amp. Chan 2 and 4 are connected with RIGHT OUT from bass amp do not wire them any other way or you WILL cut the signal in HALF which is what it sounds like you have done. You know.. i might be wrong about what i just said... Find out for me.. wire it the way i said and see if it works a lot better... If not, at least i'll know

Like to comment on Pioneer.. I have a Scion tC and they have stock Pioneer speakers in them... So, just how capable are the stock Pioneers... I was able to run my Pioneers, rated at 20w per driver on a sundown 100.4 PER channel for about 6 months without failure. They were extremely loud.. a little peaky at times.. I had then switched to some IDs and i lost a little bit of the peakiness but replaced with more subtle sounding front stage while getting decently loud for what bass install i had.

You ain't lyin! Me and you both have had rounds with Matt before..

The reason I mentioned Y Splitters is because it's VERY possible one of the channels may not be connected, working or damaged... you said you went from vol 28 to 45.. That's like almost a doubling of volume which would indicate to me.. a loss of half the RCA signal.

are you using a Y splitter on any of your RCAs? Is the gain in the same position as it was when you first installed it? Also check crossover points and make sure they didn't move either. Have you recently disconnected your battery since this problem? If you have, radio did a reset. What things effect the level? This is dependent on headunit capabilities and features- Source input level Bass Treble Loudness EQ

oh i know.. but i didn't want people to think something terrible is\was about to happen as of right now, the alternator is still on schedule.

Well.. FYI, they have until Friday\Saturday to ship it out as stated it would be ready by the end of this week.

there are MANY box builders on this site.. go down into the vendor section and ask one of them. You gotta at least categorize your posts.

oh i know, hehe, just showin what all i planned on doing.. I'm building a wall and the battery bank will be right behind it. I'm thinking about either mounting it on top of the wall(it angles down with the hatch), or attach it to the back part of the wall.

I will be using something like this i drew out for my scion tC- Does this spark some interest?

lookup the modulus of Elasticity of MDF and birch.

Don't worry guys, when the server is all up and ready,. Mark is just gonna give away some stuff and ship it to Hzd Skizzy since he keeps getting everything, lol. He got practically a whole setup now (not just from SSA deals) for crazy prices.

u would be extremely fortunate if i do. find your destiny, my apprentice, and pm me the goal and i shall use the force to complete thy path.

i take it this is not a wall.. is this in an suv?

oh.. nevermind now.. If you had 16.8cubes, i had a WHOLE design laid out for ya.. but 16.72274606 isn't gonna work....

birch is liter? Is MDF ounces? Birch is more rigid than MDF therefore Birch may have a little ring to it at some frequencies... meaning it may resonate just a hair. I do not think you will hear it though. What some people do in HT is double layer their sub box, outer shell birch, inner shell MDF to retain the density.

Scott Power Silly Pup those any good?

sounds like your wiring config is too low for current amp. Learn before you play. any questions, ask away.

maybe you should find out what part of the amp is blowing... IF it's the input side, i would be either getting a new headunit or grounding the rcas on the back of your headunit.

Ya heard.... Ya heard... Ya heard... Naw what i mean? Shit son.. Ya Heard... Ya Heard.. Naw whut i'm sayin? NO! That's what im sayin....

FLMAO!! that girl judge is like AHHHHHHH EWWWWWW!

man.. i dont know man.. That's why i'm a member and not a master of wisdom... Luckily bromo came in here and gave me some wisdom to get me back on track.

i'm assuming u are going to clamp the jumper cable end onto the existing cable that is still ran into the amp?