diablo_331

2 21inch DP's on 4 1500d's.... coming soon..opinions?

cant wait untill the SAZ2000d is released!!

no problem thats y we are here hope all goes well.

the reason for the same power handling between the different sizes is because they all use the same motor,coils,ect.for power handling people have ran as much as 4k rms to a btl but u have to know what ur doing with that much power.id say get a fully loaded btl and give it 3k rms and you,the sub,and maybe even the wife will be happy

sound like these will be perfect to throw a few on a saz3000d...or maybe they are very underrated and can take alot more for daily...

well 142 at 25ish hz will do that sometimes..lol

"10 inch icons....and a little amp" lol

u guys should see the blue angels where im station over in NAS pensicola FL,,they practice almost daily and r LOUD as hell..thats y i like them

Take 3 ft of wire on a direct connect sub, measure resistance. Take the same 3 ft of wire and put it on a sub with terminals, measure resistance. Get back to us and post the data. (That's my subtle way of saying go try something for yourself rather than spewing out things people tell you that sounds good.) think about it...get the resistance through a 3ft peice of wire..then cut that wire in half and put a common connector on each each then take the reading again..also solder is not nearly as good as raw copper.and irrc solder is the way that most companies use to connect their tensel leads to the push terminals..so just remove any and all possible resistance and youve got a better connection for running high power at lower impedences.btw i have no problem proving my theory but im stationed in Flordia and have no means possible to test this.but u can sit down,think about it,and im sure after many hours of head scratching ull understand

boner...

ive heard the icons and flatlynes....they both were amazing but id go with the flatlyne

r u even real??

the list goes on and on...give us a buget and listening preference...btw that amp might put out 2400rms with a solid electrical..but we get what ur saying

doesnt look that bad

the sae1000d gets my vote

it is does make for a better connection but unless ur chasing tenths of a db then its not needed

its your build but passives r VERY easy to build..build a sealed box with 1 10 and 1 12 cutout then tune the radiator then ur set

i think a passive radiator would be a great idea here

as badass as walling off a mini is...i think the real highlight of this build r the doors....i dotn think alot of people know how loud that will really be..good luck qith the rest of the build

u can buy them from e-gay or make them yourself..what type of sound are u looking for?im assuming ur going to go passive since ur on a budget.there r thousands of options here.budget?listening preference?

head over to Db-r.com and check out some rebuilt saz3000D's..or look around on the forums..ive seen them go for as little as $600 used...id also look at that IA 20.1

i have a 06 gms ext cab 4door...the roof was about to fall apart..put 5 layers of rammatt on the rear section and 2 on the front and its perfect...also pulled the bed off and put some sheet metal over the cab vents to seal her up...only down side is that i have to run my defrost alot now b/c of little/no ventalation...i think i might run 2 IADP 21's in 20 cubes net walled off...

will this be taken out of final price in cart or am i missing something?

i have a question about that HL Flux cap..if you had the 100amp model for example and a 250amp alt...would 150 amps of your alt be waisted(not charging batts)

^^^indead^^...i have ran single 18's and now i run 8 10's...its all what u want to hear...but by no means was the 18...sloppy..BUT the 10's are more punchy