ZED Audio

just wandering if it was built buy zed, maybe some of you guys that were into car audio then can help. one seen one since then,looks like a zed made amp. long like a crunch 50 us acoustics 2300 or a 7600 autotek or the almighty zeus! plane with no crossovers just lots of clean power. amp was black with a orange stripe down the center of the amp with yellow writing and thats about it. haveing trouble finding anything on the company or the amp for that matter. im looking for one as i type....

There doesn't seen to be any markings (to show the version) on leviathan amps.Can anybody tell me how I could verify a used leviathan is version 1,2 or 3? Thank you

Check this baby out http://i249.photobuc...xo/HPIM6337.jpg

Still trying to get over the fact that MEGALITH won't ever see production..... limping by with JBL/Crown 6K for consolation. Anyway, was talking with Stephen recently about a repair and he mentioned that he was working on an 8 channel pre-amp/processor/factory integration unit, similar to Bit 1, JL Cleansweep, RF symetry, etc. Sounded super sweet, still on , but hopefully it comes to fruition sometime in the future. I have been kicking around the idea of getting JBL MS8, but this gives me a good excuse to wait on pulling the trigger on that one.

i just bought a super clean e30,but i need the power cord/plug-in. anyone know where to find one? can i get one from zed maybe?? anyone know???

can someone tell me how rare these amps are, and what kinda power it really makes, it zed so we all know its underated. going to run a nice set of cdt hd6.1s on it. i know its a 6 ch. just found a deal on it, and i a sucker for zed goodness

Like the title says....I have a question for those running or have owned an ESX amp. ESX Q275.2 is on my Icon 10. The Icon is d2 and wired for 4 ohms in bridged mode at the amp. The bridged mode is rated at 800 watts.The hu is an Eclipse CD8454 with a pre out voltage rating of 8 volts. My issue is setting the gain. With well recorded media ....(No Ipod) Only high quality cd's....I feel my gain is too high to obtain the right output. Yes I fully realize that the gain is not a volume knob. I also realize that I could get my answer with a dmm but I don't have one at the moment. So my situation is...8 volt hu....Amp gain is at 3/4 of the dial. I have been pla…

Can anobody confirm is this board layout authentic? I looks some part nex to power suply is missing but maybe i am wrong? I realy like this amp, and if this is ok i will buy it for my sub.

Well, my business partner was on a mission to bank some frequent flier miles off some cheap cross country air-fare. He mentioned Vegas, Grand Canyon, (YAWN) then Los Angeles. I told him if we could get up to Simi Valley to count me in! Long story short, Grand Canyon was a big arse hole in the ground, Vegas was pretty cool...helps that my partner does a ton of traveling and gets the VIP treatment at hotels... But actually visiting Zed Audio and meeting with Stephen in person was tremendous. Picture Santa's workshop without so many migets. JK But actually pretty cool. Mostly we just talked about politics and having some laughs, but as always when we talk, I learned …

I am not listing in the for sale forum (nor able to) my Zed Deuce and Draconia amps with Burr Brown upgrades here. They are both being put on ebay. Just for anyone who might be interested. Seller: smcrae I bought these from Zed / Steve (or course) and am the original owner. More an FYI to those who would appreciate these vs. the ebay crowd.....

Does anyone know if this amp was made with the Chrome Heatsink? I know they made it with the Charcoal grey and black and red letters. The reason I ask is I just ran into a USA 4050 with the Chrome heatsink and I was hoping to find a 2300 to match it.

I have a friend that is interested in selling this amp, and he has asked me what I think its worth. I have no idea, so i thought that someone in this forum will have some opinions. Thanks for the help

I usually hang around phoenix phorum. I have an account here and since i just ordered some stuff I thought I would pose a question to someone who may actually be able to answer it correctly :-) I'm getting rid of a few things and posted up my USA 2150. Almost immediately the thread went south with someone wanting to know how this amp could possibly have these ratings with only a 35 amp fuse. Of course my reply, which may shock some of you was " If you run anything other than 4 ohm stereo pop in a 50 amp fuse just like hifonics" . Is this the right answer? OR ...Can the USA 2150 do rated power with a 35 amp fuse? Now for amp porn....

Will you please explain function of this component and how it is different than the Epicenter. Thanks.

Proper setting for Kronos to power up Morel Ultimo 12? Should I set to flat or LP? Using a Alpine H701 processer.

Question, this being a "subwoofer" amplifier, why does it not have a subsonic filter? Is it only meant to supply power in a sealed enclosure application??? Are the crossover points setup in a way so that I may remove the frequencies I don't want>? Example: It has crossover points @ 25hz , 31hz, 40hz, 50hz, and 63hz.. If I set the crossover points on 25hz to -12db will that "remove" that frequency's reproduction? If I leave it at 0 will it do the same? I really like this amplifier and feel that 1000w is more than enough to get an Xcon moving... My other choice would be a RF t1500-bdCP when funds allow.... Hopefully review at work goes well and I get a raise... Then I…

I am about to place an order with ZED and was hoping to get some feedback from those who might be using the NEW Series of ZED amplifiers... Please share your thought's ....

Anyone members interested in a June 2011 group purchase so We can get a discount on some Awesome products? I personally want to get a RA for the daily driver. I have a couple fellow audiophiles that have bought them & said the difference in fa nominal. After speaking with Steve about it I'm ready. "RA is a dedicated sub woofer control preamplifier. It interfaces between the signal source and the amplifier. There are four circuit blocks within RA, the low pass crossover, the sub-harmonic synthesizer, the compressor and the final gain stage. Specifications -Stereo input to mono output -24dB per octave Linkwitz Riley Low Pass crossover. -Twin band Sub-Harmonic Synthesize…

Stephen & I have been working on the overhauling of his old website for around 6 months now. We have made it to this point. The launch of the new site. There are still some changes in the works, like a brand new fresh page, and professional product photos of his awesome 2011 amplifiers! Once those photos come back in about a week or so, the site will come alive! In the mean time, feel free to check it out, comment, rate, share on the zedaudiocorp.com website! Thanks for looking! http://www.zedaudiocorp.com Front Page Online Catalog Product Page Tech Talk

Anyone have any idea what size of fusing for the new Draconia?

Steve asked me to post a little more information on his upcoming Tube amplifier, so here goes: Information on the new Zed Hybrid 4 channel amplifier. This new amplifier combines the attributes of tubes and semiconductors in a unique design. The amplifier is divided into 3 sections, the power supply, the power amplifiers and the pre-amplifiers. Power Supply: The power supply is the driving force behind all amplifiers and is absolutely part of the signal loop and therefore plays as an important part in the sonic signature as any other part of the amplifier. There are a total of 8 separately regulated power supplies within the main power supply block. They read as follows: T…

I just want to know if I can run 6 mid drivers from it. I want to cross at 63Hz and 2800hz Each driver would be on a separate channel. Tried contacting ZED Audio through pm never got an answer. Nobody answered me on the group sale either so I hope I get an answer this time.

http://www.zedaudiocorp.com/News/news.html Stephen mentioned in an email to me that his new MEGALITH will do 1KW at 4 ohms and 1800W at 2 ohms. My guess is that it won't safely do 1 ohm. I use dual 2 ohm coils generally on my subs so I'm in for a 4 piece of these. Any other rumors on this?

I got my zed minilith today. online pdf isnt the clearest. looks like I use unputs 1-4 if I run full range to amp or input 5 if I run mono to amp. my question is I have left and right sub output off deck. that means I use left or right to go into #5 input on amp..right? http://www.zedaudiocorp.com/PDF/ZedManual-RGB.pdf

Does anyone know when Zed started putting in different mosfets in the minilith? I bough a mini but havnt recieved it. Steve told me they changed the fets to higher voltage ones at one point. He told me you cant see the parts unless you remove the clips with special tool. I asked if you could tell date by serial but havnt heard back on that and dont know if I will. I just want the mini to be all it can be.. I dont want to send it to Zed for nothing though. I would think serial # would tell ...anyone know? or anyone with newer version can you tell me what your number is?