SPL & SQ / Fabrication

Crown Victorias have some pretty big trunks, i drive one. Heres a pictures Is there a way that i can place ONE piece of MDF and mount it somehow onto my trunk so i don't have to make a whole box. Its my car so i can use up that space however i want, place it anywhere in the trunk.( dont' have to worry about groceries etc.) I want to use 1 board, and the trunk itself to act as the rest of the box. Is that possible or will it be bad for my sub? Any help in this area will help, just bought a SSD 15. Or if you know any other simple ways to not have to go threw the trouble of making a box.

i need a box build for my sa-10's

Looking to build a 4th order bandpass For two 15" Orion xtr. I have a 5000 watt Planet audio anarchy amp to push them stock alt. Stock bat. 0 gage power and ground. Can any one help me with a cut out and measurements. I tried and failed miserabley.

So, explorers finally safetied.... Now i am going to start the box build. I plan on installing 2 15's for now, but 4 in total down the road. My question, would it be bad for the subs to oversize the box to leave room to cut in speaker openings down the road? The subs call for roughly 3.5 @ 33-35 hz, if i made the box like 12 cubes tuned to the proper frequency what effect would it have? How does the increased size effect the sound and response of the sub? Will their be any dangers in running a sub in an oversize inclosure for daily driving? Thanks in advance. Chris McDonald

Hi Guys, Hope you are all well and i aslo hope that some one can assist me with working out the correct spec for a true SPL box. please note I will only be doing SPL with this box. Ok so I have 18mm ply wood, 1 12inch subwoofer, 1 amplifier and 1 battery. Here's what i'd like to do Get a minimum of 151db's from this setup Equipment DD Z1a NSB 170 12v Targa TG301-DW The sub specs are as follows and i could be wrong because this is taken directly from the site. 12" COMP SUBWOOFER - DUAL 1 SPECIFICATIONS Fs (free air resonance): 48.7 Hz SPL (efficiency, 1W/1M): 89 dB Nominal Inpedance: 1/2 Ω Qts (total speaker "Q"): 0.606 Qes (electrical "Q"): 0.732 Qms (mechanical "Q"): 3.5…

its for to 10's

Finally picked up a few sheets of MDF to play with to make my explorer box, what should the minimum port area be for 2 15inch RE SX's? So far i have messed around with the RE box tool and came up with a 6.1 Cube box tuned to 34.7hz with a port area of 74square inches. My available measurements seem to be 41 inches wide(before wheel well bumps), 18 inches deep, and i don't want to reach over 20 inches high on the height. If anyone can throw some suggestions at me for the area of port needed or maybe a box design they have used in their explorer it would be much appreciated. Thanks!

Big dilemma, trunk car im working with. I have 7.445 Cu Ft internal area for use if i fire up but the box will be removabable so i can grab my spare tire if i need to. Will up firing in a trunk lose me alot of spl or clarity? Which direction should i fire the port if im making this setup. Also for two RE SX 15's how much port area should be used? The port area is a very limiting factor as its robbing the little amount of area i have. The other way i can do is rear firing but i must make a two piece box to fit it in the trunk. The subs would only be 2 inches from the rear lid of the trunk. I gain .2 cu ft from switching but the amount of work would be substantial and i wou…

Is it cheaper to buy my own MDF and make a box than having professionals at a audio store do it? I plan on having a SA-12 and a box Ported tuned to about 32hz with about 1.7 cubic ft of space. I have the measurements and such. I used the re audio box calculator. I can get help from my woodshop teacher and some friends but I'm curious if it's cheaper. Idk how much they charge at the audio store but I'm sure it's not cheap. And another thing how good is birch over MDF? I can get birch free but everyone tells me MDF sounds better. Build would be musical and everyday driver not spl. Thanks guys can't wait to hear from you all.

what did you guys you to build your ported box? i mean how did you figure out port length and tuning? what programs did you use or equations.

Hey guys I am in meca and I am hitting a 144.9 on music with the car off because I am in AS2. I was told at the lastest show the Vinny if I were to make a so called fart box box size of 3.5 cubic feet with like two 6 in aero ports and tuning at like 50 hertz my current setup is 5 cubic ft after displacment and tuned at 40 htz I beleive. What I am wanting to know will this so called fart box get me any louder and see the bad thing is we don't have anyone with a termlab around me to test it. My set is a up memphis mojo 15d2 and I have a sundown 1200.1 with four guage and soon to be hopefully two runs of 0guage. Any help with this guys would mean alot to me and my dad. Also…

I need help to build a box for one 12" Fi Q in the back of my regular cab GMC truck. I don't want to compromise sound quality and i do want it to get loud. What i was thinking of doing is fiberglassing the bottom floor behind the passenger seat where a box would normally go and use MDF for the front, sides and top. I 'm not the best at 'glassing, it works but isn't pretty. I'm trying to get there recommended size of 1.2 - 1.3 cubic feet. Any ideas to start??? If any one has any ideas please let me know i am open for suggestions. Thanks in advance I want to run a 12" Q and a Sundown Audio SAZ-1500D.

Alright so iv made my box and everything and I would love to use body filler to smooth t all out and cover allscrew holes. I don't really want to spend any more money for this box... What's the cheapest way to obtain the perfect box?

Hey all.I REALLY want to build my own box but im worried that it would be to hard to do.I would like a simple dual 15" ported box for my type r 15's.I just don't know if its something I can tackle or not.So my question is in your guys eyes on a scale of 1-10 1 being easy as pie 10 being hard as can be,how tough is it to build a ported box?Also is there like a site or something that can help me with a design and other stuff like that?Thanks

As far as sealed enclosures are concerned, I find myself to be pretty knowledgeable. When it comes to ported enclosures, thats a different story. Ive been reading quite a bit and tryin to find out how the fudge to make one - mainly the port itself and how you incorporate this with the rest of the box. When i look at ported boxes it looks likes a pucking maze and i havent the slightest clue how long to cut each piece of wood <-----thats just one of the many things im not educated on....I know about displacement and all that good stuff but still find myself extremely confused when it comes to ports....if anyone has a site i can go to and read up that would be appreciated…

Hey guys i built this box before i even got the subs just wanted to show you guys. The dimensions are 30x14x14 its 2.5 cubes tuned to 30 hz (2) 3 inch areos 14 inches each. let me know what you think. And how you think it will sound. im going to put 1700 watts rms @ 2 ohm with my saz 3000d.

Im trying to make a box for a single 12" dcon can you guys give me your feedback and let me know what you think please? im new in building boxes this is my first and looking for it to be tuned at 32hz demensions for the box are as seen in the calculator( long story on why i chose those measurements and dont want to even explain why) let me know what you guys think please and also for my port according to this what would be the sizes of the 2 pieces of wood i would cut for it? thats only thing im confused about at this point.

My 15 will be here today, and ive spent the last week drawing up designs but before i commit to any, does anyone have a more accurate box calc than Re.com? My friend used it and his came out nearly a 1/4 cubic foot bigger and tuned like 4~hz higher than what re box calc told him.

I'll be building a new box this weekend for my new Xcon 12. I have seen quite a few boxes with black carpet and white ports lately, and I really do like how they look. So I was gonna try one myself. Parts Express has some black carpet. One has a latex backing and the other one doesn't. Is there a plus to one over the other? Should I be looking else where for carpet? What have you guys used? I've never done carpet, just textured paint, and want something differant. I am just unsure what to get. Any help would be appreciated. Thanks, Tony Nelson

ok so one night i was sitting around thinking up some new box ideas. i really want to have my sub facing forward into the cab of my car, and have the port be on top of the subwoofer. so i was doing some concepting and came up with this, Pdf of box idea. I just want to know if it will work before i start building i forgot to put notes so.... notes: 1. double baffle front plate 2. round port edges 3. 2.8 ^3 feet of airspace after all displacement 4. 3/4" mdf or particle board used. its going to be firing forward with the trunk sealed from the cabin. thanks, Anton Miller

I have a 95 caddy deville tryin to put 2 18' in it and the space im working with is 51x32x18. Need help please

my friend has 2 15"s just sitting at his house and needs a box for em. he's got a 2000 s-10 blazer, and the cargo area is i believe only 36 or 37" wide between the wheel wells. any help on a design for this would be appreciated. we should be building it next weekend.

Okay guys hope this is in the right spot! I didnt want to post this in the fabricators thread but anyways here we go. I'm wanting to purchase a box design for 2 12 L7's. The only dimensions that matter is I dont want it over 20 inches tall and over 48 inches wide and 16 deep. I dont want to do a basic slot port or aero tuned port. I'd rather do a TL or something of the sort. All I want to purchase is the design not the box guys. Something cool and out of the ordinary. Thanks in advance guys!

plan on making a box for a box for a DC level 4 18" what do you think?

my friend wants me to build him a box for his 2 12" lanzar vibe dual 4's and i cant find any specs on these subs let alone what cubes/tuning freq. to build for, its going to be ported for SQ-L if anyone can help me out. thanks and aparently if i try to just type SQ-L without the dash, i get LSQ?