SPL & SQ / Fabrication

I built my box today it is around 1.75cuft and I went ahead and sealed it. I took a old circle port out of a old box I bought and it is adjustable! I was like holy crap.. anyways I believe it is a 4" port and it adjusts from I believe 4 inches in length to around 10-12 inches. What would the length of the tubing need to be for lets say.. 30-32hz?

I'm making a box and the port needs to turn. is it pretty simple like so... thanks...

I want to design a ported enclosure with one DD9512g to put in my single cab chevy 1500. I want it to be loud, but also as musical as possible. I have about 3.3 cuft to work with. The enclosure is going to be a center console enclosure. If I find the frequency which my vehicle peaks at, will this help me choose my tuning frequency of my enclosure?

What up SSA. Thinking about ordering a single Gcon 12" and running it ported but just want to make sure my calculations are accurate before doing so. Volume (Net): 1.81^3 ft Dimensions: 13.5" (H) x 30" (W) x 12" (D) Tuning: 32.75Hz Number/Size Port: 1 x 4" Flared Port Length: 15.5" Port Area (per cube): 6.94"^2 Vent Mach: 0.11 Is there enough Port Area? Is this a good size/volume for a 12" Gcon? Also, I plan on placing the woofer and port on the same baffle, on opposite ends. This would require a 90 degree elbow bend for the port but there should be over 7" of space between the end of the port and the subwoofer so I don't think that will be a problem.

How much port area you think would be best for 2 18" zcons. . Will be in around 16 cubes in a b pillar flat wall on about 5-6k rms

Hey fellas, I'm looking to change box design. I want it to be port forward. The dimension I have available is 32"W x 12.5"H x 29"D. It is running on a bc2000. I am trying different boxes until I can get another xcon and have no experience with 4th order builds. It will be a 98 mustang trunk wall. If there are any details you need let me know as I have no knowledge of 4th order designs. Thank you to anybody who helps.

Who has any experience with CF? such as: http://www.fibreglast.com/category.php?cat...src=HelpfulProd

I have been running 2 12" zcons for little over a year. 6 cubes 38hz 80cuin of port area. drivers side port all facing into cabin spray foam sealed of family car. trunk build. still have to load kids in back seat. seats fold down. Always been run at 1 ohm. I was using a saz3500v1. when I built that box and tuned it. I recently bought a B2 M1s to run on these subs. 7500w @ 1ohm. with the power increase I was looking for any help with what the new box would require as far as net volume. Looking for help????? suggestions???

Currently running my 12" ICON in a 1.35 cu ft sealed enclosure. The car is a hatchback. While the sub itself sounds clean and puts out decent volume, I'm often wishing it hit the lower notes a bit better and was louder. Is anyone able to help me design a ported enclosure for this sub? I'm trying to keep the footprint of the enclosure as small as possible, but I understand it'll take more space than the sealed setup currently. This is the current setup: Untitled by riored4v, on Flickr Regarding the height, i can't really go much taller since this still allows me to use my hatch cover to keep everything out of eye sight. Its at 13.5" tall. Any help would be ap…

Hello, I am building a box for a friend and I had my MDF all ready to cut, measured out panels and everything and he calls and tells me that he want an aeroported box. I have searched and read different things in this section and after figuring out slot is actually a lot more different than aero ported, I just don't get it. So, I have come for some box designing help. Dimensions: Depth: 16 Height: 16 Width: 40 It is for an Fi X 12. Was hoping for 2.0ft^3 at 32hz I really just need to know how many flared aeroports I would need with no port noise. Diameter and Length of the aeroport would be nice. Thanks in advanced, Jay

I'm really confussed on ported box tuning and sizes can anyone help me work out some measurements for my enclosure i have two ascendent audio havoc 18" subwoofers , and two Orion D5000 amps to run the subwoofers . The size of the space I have is 34high x 20" deep 53" wide which is just over 17cuft i'f I've worked it out ok I would like the box 16 cuft and tuned for the lows because want to create hair tricks . The design I would like so I can make into a wall build . Help

I don't really want to order this stuff and have to wait for it so i wonder if i be alright using some things just lyin around the house? The space i got to fill isn't too large really. IT's about 3-4" wide and about 8" tall and the deeper the better. I was thinkin about stuffing all kinds of shirts that i dont wear anymore in there.. I'm sealing a wall and i gots to seal around a window and i'm not spraying foam on my glass so thick material is the only option. You think shirts or blanket sheets will work fine?.... then i'll just spray foam on this to complete the seal...

I'm wanting to know if I build a box like this and would it be ok with the ports like this. It would go in a 95 honda accord 9.67ft^3 gross, 7.34ft^3 after ports, after bracing somewhere between 7 and 6.5cubes after bracing, depends on if i invert it or not thanks for any suggestions or comments

Hey all.Is it true that you can build a wall and then slide it in your car?Ive heard of people doing this but wasn't sure if it was real or what.If its real how would I go about doing it?I want to build a wall but I dont want to spend 1200 bux to have some one build it so I was going to attempt to do it myself.I have a 2007 Dodge caliber and was wanting 4 15's if it helps any.

so my friend tried to paint the box he made for his girlfriends jeep black, but where the screws are its all messed up, and the paint is dark and light in some places and fades alot and doesnt look that appealing all together, i figure i could just use woodfiller for the spots for the screws and sand it down flat, but what about getting all the paint even and pretty? need to make one for a guy i know and he wants it painted so anything will help, thanks

Still doing my Thunderbird blowthrough build with the 2-12"BTLs but Im already looking ahead of what I can upgrade to. I know what I wanna do (no Im not telling). Soooooo I want some opinions on a enclosure I thought up. The question is really about the direction of the port. The box will be a half L and half T shape.....(removing rear seats) part of it would be in the trunk but most of the box is in the cabin. so the subs would be facing up with the port forward. reason why I want the subs up is so I can use some plexi. It'll be just above shoulder level. Leveled with the rear deck. This is what Ive drawn up. Do u think the port will be fine facing forward? note this is …

I moving up from an old 200 rms orion 12" sub to 2-fi ssd's with 1600 watts to them ( or what ever my Soundstream will really put down. lol ) Now looking at the follow 2 box designs from here, ( which is super sweet that you guys posted these! ) Box 1. 12" xcon ported Box 2. 12" icon ported Outside of what appears to be an extra dolly of vertical bracing and total port area are the pretty much the same. Of course the overall dimensions are a bit different, but they have the same internal volume and tuning frequency. So which box is better? More port area make a difference when tuning is the same? Any in-site is much appreciated. Got the email today that the subs shippe…

Plan on running a pair of M1a's strapped @ 2 ohms for daily/bassrace, and @ 0.5 ohm for burps. Just under 3 cubic feet tuned @ 38hz 72.5 sq in. of port Does it look adequate?

Ok I had to do an l-port and It is 6"H so I marked all the way around the L at 3" in the middle and from front around I have got 22" but all the box calculated says phical port it 16" so is my port 22" or 16"?

Anyone no what size t-nuts to use in double baffle box for 2 sa 12s

Whats up guys...Heres a box I finished up yesterday. It is a transmission line tuned around 31Hz. Right now there is an EHQS 12 (SVC 4 ohm) in there. Amp is a JBL CS200.1. Rated at ~200 watts at 4 ohms. As for how it sounds...FUKIN AWESOME. The tonality is a lot different from the 2.5 cu ft @ 30Hz box it the EHQS was in and output is a lot higher. This thing digs deep and has usable response down to 25Hz testing with sine waves...below that it unloads and doesn't have much output. It has a pretty flat response from 28 - 60Hz. I really love how it sounds. It's easy to tell when the EHQS is reaching its mechanical limits as I can hear it bottoming out but that is…

I just copped 2 new 15" Alpine "Hype"-Rs for $200. Wanna play around with them & just see what all they can do. Ive always wanted to just see what they sound like cause I NEVER have. Ive been told the lows suck for the R so what kind of box could help put for that? 7cuft box tuned to 34 or 35hz? P.S. NOT my daily subs...

i just went on car stereo.com and i have a 2 cu.ft. box and to tune it to 34hz with the sub being an icon 12 the round port would be 4" diameter and 11.72" long is this right

just like it says if someone has experience with a 72' bug and or a BTL 18 I am looking to redo my box and need design help. Please PM me on here. I just know I can get louder than 144 with a exile 2400.1 and a standard BTL with cooling. Thankx MC

i need a box build for my sa-10's