SPL & SQ / Fabrication

So I am thinking of venturing into unknown territory and build my first ported box. I have been doing a little research but am still learning. As I understand it, frequencies below the tuning of the box can cause the driver to "unload" which can cause damage. I am not 100% sure what that means, but I digress. I have read more than a few threads that say they tuned their box to 32 Hz and then go on to say that the low-end is amazing. Now I listen to mostly rap music, and it seems like to me that there are a lot of songs with frequencies below 32 Hz. There are a couple low notes in Jeezy's "Hypnotize" for example that I am guessing dip below 32 Hz. How is it that the box ca…

When mounting subs like this, can you make the enclosure smaller than recommended? For instance, if the subs call for 1.5 cubes each ported can you get away with making the box 2-2.5 for both? What are the (dis)advantages to mounting subs like this? Or are there any?I know the polarity needs to be reversed with the sub mounted inverted.

i am looking to build a wall in my envoy.... it will be a 4 15 woofer setup and i need a minimum of 16 cubes to make it epic..... what type of port do i need and i would like it to be tuned to about 38 hz but i mainly listen to rap so i am considering 32 hz as well...thank you

ok so i cant read a tape for nothing so i got the guy across the street to read it for me on my box iv'e asked this questions a few times but never had the right messurement's but now i do here they are the depth is 22'5/8 the lenght is 41'1/8 the width is 22'13/16 i have two L shape ports the messurement are length 4'3/4 depth is 18'1/4 and the bottom of the L sape port which gose toward the center of the box is 10'1/2 remember i have two L shape ports one on each side of the box with the same messurement's now at the bottom of the L shape port where it goes toward the center of the box i have 5'1/2 from the L SHAPE PORT to the back of the speaker box these are all …

Hey all... got another question here . If you use aero ports, is it possible to build the box smaller in relation to a box with slot ports, or is the port displacement the same for both types? Thanks

Ok, so this weekend I plan on pulling out my box and putting the zcon's in. 2 12" 1 ohm z's goin in. Gettin the diehard platinum marine sat nite and puttin the saz2500 in. Rt now my box is 4.75^3. Its an angled box to fit behind the seats of my 3 door s-10. I have another 4" of room I can go up. That would be about another 1.4 cubic feet or so. Rt now the port is on the side and has about 78 inches of area. 19.5 wide by 4 tall. Is that enough or should I make it bigger while I have it out? Or should I leave it alone? Also what would be a good gauge of wire to run for the subs? I cannot wait to hear these z's rumble!!!!¡¡¡¡¡

its going in my 92 civic 4 door in the rear seat area i was thinking sub up port up...but curious to see what sub up port forward would be. only reason to go in that area is because we could barely get a 5 cube box in the trunk without beating some stuff in box is gonna be 6 cubes at 36hz anyone have an experience in a setup like this one? im not sure if its exactly legal in most comps because the box itself is gonna be over the window line unless they would consider it a wall?

So the time has come to finally make my box as work has slowed down and my carpenter (father) has some time to help me get a enclosure made for my pair of RE SX 15's. My major dilemma here is that the opening for the trunk limits the size of the box to be rather small compared to the trunk size unless i do one of two things... Option 1, Build the box in 2 halves then screw together inside the vehicle. Other then volume taken up for the small 2 inch border around both halfs of the box i plan to connect them with, what other problems could the pose for the sound of the box? I'm able to get like 12 cubes into this trunk if i am able two to part this box... Option 2, Build th…

I have a 97' Thunderbird that Im doing now. I wanted either a pair of Fi BTL12s or Fi BL15s. I want the BL15s because I would save a lil money on power and can be used in other areas such as the build, elec system, etc..... But the enclosure size needed is kinda on the large size for my trunk. But I can fit them in there if I angle the baffle and use 2-6" aero ports. My real question is I was reading on another forum that a guy with a mustang (which is basically the same trunk as mine) had success with his subs facing forward and his aeros on the side. He said that subs back/port side was the loudest on the meter but subs forward/port side was the loudest to ear. Has anyb…

Looking at sub manufacturer recommendations, box sizes for each sub can vary by quite a bit. I'm just curious what the difference is. I know that a larger box decreases power handling of the woofer, but is there any difference in sound? Is a smaller box more susceptible to peaking? Sorry for the newb question - I'm trying to decide what will fit in the trunk. Thanks guys.

I'm looking into building a new box and was wondering if there were any suggestions on the port's location. Its an extended cab truck and the subs and port will be upfiring with subs inverted. When competing it will most likely be USACI outlaw scoring with drivers door open. Would it be better to put the port on the passenger side, driver side, or center of the box?

So I decided to pick up another Sa10 so I can wire down to one ohm. Now I just need to figure out how to fit these in my Infiniti I30. I've always done sub back, port back but can't with the four tens. I'm thinking about doing port and subs up, I've also thought about subs up port through the armrest. I'm capable of designing and building the box, just wanted to know if anyone had any advice about the layout. Thanks -Rick

My dad has an E8v1 in his van in an old box that was from a component set, he needs a new box. I have leftover wood from my box so I thought I might as well use it! Using sundowns recommendations I figured .6 cubes with a 7x2 PVC aero port. My question is how much port area should it have and what frequency to tune to. He listens to rock music, should I even port it?

Relatively new to these kind of speakers(power hungry, big foam, high excursion monsters). Used to my old Orions and JBL GTI(the real ole ones that were based on pro drivers). Anyway, picked up a pair of these Eclipse SW8122DVC...spec sheet here(found in a different thread on this forum....TYVM) http://www.cartoys.com/cartoy/pdfs/Eclipse_spkr_manual.pdf The sheet seems to call for a sealed box.....but I have a feeling that a slotted port might be a good option too. I am shooting for a SQ system(yes I read here that there is no such thing as """""SQL"""""....lol, and I get the point, but I have had plenty of SQ systems that got REAL loud....sorry, it w…

Today I purchased 2 kicker L7 12s and a rockford fosgate prime 1200. Can someone help me with a design for my 1998 s10 extended cab, my max dimensions are 46" wide, 22" tall, and 13.5" deep would like it tuned @ 33 Hz. Any help is appreciated

Could I get the same output if I use aero tubes on my box instead of a regular port? I want to get a 9cuft box for the new 15" BLs. Would the aero tubes make the gross area of the box smaller because I want the box as small as possible but still have about 9cuft of area after displacements?

Alright, I want to switch to Aeros from my slot port to give my subs some more airpsace (2 15s with 5.5cubes is a little small for me).. anyways could anyone help me out here, I know how to design a slot port but not a aero port. How many would I need to get proper port area and the length for say 31-32hz? Box is 38.25wx16hx24.5d

Do crx boxes work in a trunk with the subs up an ports faceing the back?

Ok guys, I'm gonna need some help with an enclosure. First, some background. I have a friend who everyone had him talked into buying the usual kicker stuff, but luckily I got to him in time. This will be his first setup. Anyways, I coached him through buying an AQ2200D (could have chosen a better amp, I know, but his budget was sort of limited and we didn't feel like going through the hassle of looking for used deals on others), an 18" DC Lv5, and all the other bits. Should all be getting here by the end of this week. Alright now to the enclosure: The vehicle is a 2005 Tahoe Z71 (captain chairs in the rear). Now I measured awhile back, but if I remembered right, it should…

http://www.slapshow.com/slapem/SLAP_dBQ_Scorecards.pdf the 3rd score card....for slap dbq street format can anyone explain to me what the following parameters men exactly.... wire termination wire protection battery venting safety equipment safe operation head unit integrity amplifier integrity speaker integrity processors and xover integrity wiring integrity and a tad confused on the floor noise...what exactly is that?? road noise? any/all help would be appreciated....

Awaiting a check for $450 and then putting a call into RE. 4 RE 8's 1.8 @ 34Hz dual 3.25" Ports under the seat of an '03 GMC 1500 Ext Cab. going to be powered by Pheonix Gold Octane R 8.0 Hoping for 140 on the AC. Which shouldnt be much of a problem.

Hey, i currently have my box in about 1.6 cubes to low 30's, and Mike told me that 2cubes net at 34 would give me more output. I want to make sure i won't lose SQ, but i might give this a try. Will i gain much output with this change? Will i still have excellent SQ? I searched a ton on here and caraudio.com and read up on ports, square inches of port area, etc, and i used various calculators. I used the calc on maximacar.com, which is the best i have seen. The box dimensions are: 24x14.5x15 with a 4 inch by 11" port. The calculator takes into account woofer displacement and displacement of the port, and it comes out to 2.29gross, and 2.06 net. With the box being 1…

I plan on going with 3 -10's box will be 3.2cf after sub displacement will be using 2-3 6" external aero ports. Tuned to 32hz and running 2k. Subs in mind are sa's or skar 10's maybe even custom built 10's from splaudio. Box will be subs back port to the front.

I have 40"x 15 x 25 to work with. Would this be sufficient for either 4 sa-8 v2's or a single dc lvl 6 18" assuming it'll fit physically. Its going in a 2005 civic sedan with a 220-250amp alt, 2-4 xs d31's and probably a stetsom 7k or similar. I would like to have itforward fire into the cabin while being sealed from the trunk.

I would like to get a few different tones on a CD or something to play around with, where can I find some? Thanks, Mike B.