US AMPS

Many people say that the old school us amps were better probably because they were made in the US.At least in the 21st Century how good or bad in terms of circuitry are the amps compared to old.( I know US Amps AX Line are made here)

Does anybody how much power this amp will put out with a healthy 14.4V at 1ohm??

Hi guys, new to the forum... just looking for some input from people that are familiar with US Amps and RE Audio. I just dropped some cash for my new system, and was curious about your opinions on my choices. I haven't installed anything yet except the deck as the amps and cap won't be here until next week: 2001 GMC Sierra Stepside - (STANDARD CAB!) Head Unit: Pioneer BT9800 (Bluetooth rocks on this deck!) Subs: 2 RE Audio SE 10 inch (new logo) - will be wired to 1 ohm Enclosure: Custom Built Sealed @ .65 cu ft each (optimum according to RE) - 3\4" MDF (Air tight, trust me!) Sub Amp: US AMPS XT-4000d (2007) Front Doors: Infinity Reference 6.5" Co-axial (Existing, curre…

U.S. Amps is looking for a Professional Car Audio Installer/Fabricator! Must have a good reputation in the car audio world, must have extensive experience installing and fabricating, must be willing to relocate to beautiful sunny Southern California. SERIOUS APPLICANTS ONLY!! E-mail me at [email protected]. Submit professional resume, photos of installs and other work and list of references. Please repost and share!

I have 2 US Amps Md3's strapped. My question is will both of the amps be putting out AC Voltage or just the master? I went out there today and on music my master was putting out AC volts but my slave was not putting out any AC volts. Both of my subs work and they are wired seperate so both amps are working but the slave is not reading any AC voltage.

Would like to use this along with my USA-1000x! Anyone know where I can get one? Thanks!

ok as the title states i am wondering if the md3d is .5 ohm stable because i going to be running 2 12" SX which is dv2 so my ohm choices are .5,2,8. and the electrical system i have is this, 200ish EA alt, 34/78 yellow top, 2 hc2400 and is all wiried with 1/0 guage wire, and also 1/0 big 3.

im lookin for a set or 2 or xxx components. i live by detroit can anyone help. i have no idea were to find em thx

How to identify amps with SAT?

US Amps Merlin M2130 US Amps auction Never seen one like this, just curious if anyone knows anything about it.

I know they had some limited stuff in the past. Just wondering if there are plans to expand into this side of the industry.

Will these amps do rated power? I have heard mixed reviews about the power they put out some say they will do the power plus some and others say that they will not make power. Also how is the build quality I have heard that they have went downhill compared to their older amps. And if they do rated power at what voltage do they achieve it, I am assuming 14.4 which I will never see my truck idles at 13.8 and runs at 14-14.2 at 2000 RPMs also how efficient are they? Pretty much are they worth the money or are there better built amps that do more power for the money?

I just purchased a set of XXX6.5 components from RE and would like to run it active. Would you guys be able to give the the ideal crossover points at what slope to run the mids and the tweeters ? There was no white paper/specs that was included in the box my gear consists of Alpine 9887 Audison VR209 (200w x 2 @2ohms) to the Mids Audison VR203 (70w x 2 @2ohms) to the tweeters Audiosystem amp 780watts@2ohms RE SE12 @ 1.1cuft sealed box Thanks and hoping for a quick reply

Has anyone ever had or heard a modded US Amp? I am speaking to a guy who says he upgrades US Amps and when I asked he said he makes them sound clearer. Any idea what he means?

Would I be able to run the MD22 at 2ohms x1? Looking to power a SI 12'' BM -Ben

Hi guys, last weekend I picked up 2 of the US Amps AX1000 (for now), and I'm using them to run (3) 2 ohm Cadence Wild Beast subs (for now). How do you strap the amps together without using the magic "MLT" box? Under the plexiglass, I can see the "master/slave" switches for both channels, but I'm a little leary doing anything to the circuit board without some instruction. Down the road, I'm planning on adding at least 2 more AX1000's and one more sub, but this current set up will get me thru the week. Thanks, in advance

Has anyone benched one yet to see how much power they put out? I am wanting to know how much continuous power they have been tested to put out at a 1 ohm load, before clipping, at what voltage did it put out that power, what THD, etc. I just want to hear from some people that have actually tested them

What size wire should i use for this amp. I will be running it @ 1ohm to two rl-i10's. USamps website says 1200rms @ 1ohm, but I've read here that its 800rms @ 1 ohm. Thanks Ben

I have two of the 2004 model MD2D amps and was wondering if they were strappable or if it was a god idea to do so? I'm planning on running them on two Orion H2 15's with dual 4 ohm coils. Would i be safer to just run each amp to a single sub?

Hey guys I was curious if anyone had any idea what a US Amps 3000 de 2006 model should sell for. It is still new in the box. I have one that I will be selling and would like some idea as to what to expect. I was going to use EBAY but after looking at amps there I am thinking twice. Any help would be appreciated. I dont want to lose too much money on this if possible. Thanks. Charles

Hey guys what are the real Dimensions ofthe 2007 US Amps Merlin Series? I'm interested in the MD-3D and the MD-21 but since i'm tight on space i wanna know the real Dimensions before i buy. Here on SSA I've seen that the MD-21 WxHxD is 7.9 x 2.5 x 8.75, on www.woofersetc.com I've seen it the same, but on their website it is WxHxD is 10.5 x 2.5 x 10.75.(now what?) The MD-3D here on SSA it is ?? x 2.5 x 8.75 WxHxD the W is unknow( wich in my case it's very important), on WoofersEtc.com it is WxHxD: 13.8 x 2.5 x 8.75 and on their WebSite it is WxHxD: 21.75 x 2.5 x 10.5, now I'm very confused and i realy need to know the real dimension mainly the W(L) thus how long they are…

Hi guys! Came to find out how people thought of the various usa/re-audio amps - thanks for all the info! But a suggestion - the pinned topics are the 2007 models? there is a 2009 model thread and we are already into the 2010 range (my local dealer has the gen2 xt v3 coming next week) maybe turn the pinned thread into a specs round up with all the models by release date? Thanks again, Jen (doing install for a 1999 delica rv)

Hi there Could anyone tell me if i can use a AX-2000 with a JL12W7 sub? i know is 3ohms but was thinking maybe it could work!... Im not a SPL freak More a SQ guy so anyone help me out living in sweden and nobody here have the info i need best regads Dag.Z Stockholm Sweden

Does anyone know where I can get the older model Merlins at? im looking for a MD42, I tried checking ebay but they only have a MD41 up 4 sale.Im probably plain old S.O.L. but it doesnt hurt to as. So does anyone got any for sale or know where I can find me one. I would like one preferably new but used is fine as well.

i was just wondering can the old 1999 us amps 400 be modified to do 1200 @1ohm bridged instead of its factory setting of 1200@2ohm bridged? just curious. i have read about people having amps modified and was wondering about this one. thanks for any info.