Sundown Audio

Is there an easy way to make one of the wired remotes into a master volume control for all of my 100.2s? My HU doesn't have a knob. I like knobs.

Hello I was wanting to use the 100.4 for my front stage. I was going to run 6.5 in the kicks and maybe a 3 or 4 inch in my front pillars. I was wondering can you bandpass, for example channel's 3&4 with the subsonic filter set at 150 hz then setting the Low pass frequency crossover at 4,500Hz for the 6.5. Then channels 1&2 would be set on High Pass and the High Pass Crossover set at 750Hz for my pillars. I will also be running tweeters I will be running those on channels 1&2 also. How could I Passively crossover these. I was thinking around around 7,000-8,000Hz any info would be helpful. Thanks

i am going to be running 2 12" Q's w/ bp power off of a sundown 2000 that i have preordered. i also plan on ordering a 100.4 sundown amp also for my 6.5" and 6x9's. i was looking at the knukonceptz dual amp 0 gauge wiring kit. what size inline fuse would i want and also the 2 fuses on the distribution block? also for the rca cables there are options for 4ch and 2ch. i am not sure of what i would need exactly. sorry for all the questions, i just want to try to get everything right the first time. thank you in advance.

I rewired my sub from 1ohm to 4ohm & was wondering do I need to reset my gains or redo the wiring config. from my amp to my sub ? My set-up is in my sig. line if that helps. It sounds the same but maybe not as punchy as before & it has a little less volume in the substage. I can hear my front stage alot better now also. Also I messed up & stripped out one of my screw mounting holes in my enclosure. Is there an easy fix or should I just go ahead & get a nut & bolt for it? Thanks, Chris.

im sure its been asked before but im about to strap my amps today... so do the gains need to matched or does the master control gains for both amps?

Hey Jacob are Sa-8 avaible the aluminum coil? And would I need them if 1 put 4 of them on a saz-3k @ .5 daily

I know there not out but do you think 4 of the sa-8 could get louder than two 12"inch woofers.Both would be running off saz 2000?Its just hard to believe 8s can get that loud,but man that would be badass.how big would a box half to be for 6 ofthem ported?

what is everyone getting on a saz 1500 output voltage wise ?? i did my set up with a 60 hz tone crossover set at 80hz..speakers NOT connected.. i set it at 39 voltz...output AC sounds good but not very loud at all.. maybe i am doing something wrong ?? i know they can get louder .... help..

i got my SAZ-1500 today! woot! just waiting on my box from Audibel Customs to ship here, and later this week ill order my bl 15 and 1/0 wire. this amp looks amazing, and is the heaviest amp i have; the most powerful one by far. cant wait to hear it!

These are available : USED 100.2 in good shape w/ box and remote (1) - $170 shipped USED 100.2 in good shape w/ no box and no remote (2) - $160 shipped MINT 100.2 w/ box and remote (3) - $180 shipped B-Stock (Tiny Mark) 125.2 w/ box and remote (4) - $185 shipped USED 100.2 beat up w/ no box and no remote (5) - $140 shipped

I would like to know how much is the recone for ns 12" and whats included in the recone package? TIA.

Hey Jacob, I was wondering how much excursion is safe with these 10's. On some heavier midbass songs they get goin with maybe a half inch of excursion. Theres no hint of distortion o just want to make sure they were designed to handle this.. Thanks

If i was to be running re audio components all around would the SAX-100.4 be able to power up those speakers pretty good?

I have a JVC KD-AHD59 HU, front components and a Polk 4ohm SVC sub. I am planning to run the front components on ch 1/2 and bridge the sub on ch 3/4. The HU has 4 preamp outputs, line out L/R for the fronts and L/R outputs for the sub. I'm confused by the L/R sub outputs. Can I run those 2 sub outputs into ch 3/4 inputs on the amp and bridge the amp outputs for the sub? Seems odd to me. Please advise. Kent

Had a friend of ours in the industry put these on their Amp Dyno to verify power since people have asked us about it. All SAE amps meet or exceed ratings @ 1 % THD on the Dyno. SAE-1000D v.2 : * 1 ohm Dynamic test; works out similar to clamped results SAE-600D : * Certified; when I did a "clamp" test on the prototype it worked out similarly to the SAE-1000D Dynamic burst as I clamped around 50% over the certified figures. SAE-50.4 : * Per channel * Per channel * Bridged @ 4 ohms

How do I measure it? I have a pair of 1500s strapped on three Fi Bl 18s (dual 2ohm) in a series/parallel configuration. I've already clamped the amplifiers and they are pulling 460a of current, voltage drops from 14.4 to 11.8, and resting resistance is 1ohm. What else is there?

I was driving and i heard a pop and my front speakers went out I know it was the amp not the speakers. The rear speakers still are working which doesn't make sense. I have 2 amps a 1500 sundown running the subs and has no problems and the 100.4 sundown running 2 front speakers and 2 rear speakers. I checked the fuses on the side the three green ones and none of them were blown. Like I said the front speakers just went out and the rear ones still play. I also unplugged and plugged back in the input cables. Any info would be great. Probably a Hardcore Newb question but I don't care I will play dumb to get a better answer.

NeoPro-8 models are now SOLD OUT. Also -- all NeoPro speakers will face a small price increase due to the Neo cost increases. The next run of NeoPro-8s will include 4 ohm models as well. We will have more in stock in June... the demand for these really snuck up on us exponentially rather than just a gradual increase so supply was literally pulled right out from under us! We should have more steady data on the demand in the future on these. New / Old Pricing : NeoPro-6.5 : $99 / NA NeoPro-8 : $105 / $99 NeoPro-10 : $129 / $115 The 10" has a much bigger piece of Neo in it so was more affected. If Neo goes back down in the future we'll adjust accordingly -- we may also offer…

Just thought I would post some pictures of my 1500D's. I did 149.2DBs with 2 Sundown 1500D's on an 100 amp fuse. The sub used was an Atomic APX. The score was at the headrest. Without fusing during my clinic I did 149.9DBs. All in all very impressed with the amps can't wait to get 2 more. I didn't have much time to test before the show but I believe with a little more tuning I'll be over a 150 at the head. The 149.1 was the second day.

I received my refurbished sae-1000d yesterday. I actually looks really nice. The picure here showed a couple of little marks on the cover, but they are hardly noticable. Hooked it up at 2ohms and wow! I was very impressed with it. The specs say that it does 600rms at that resistance but it definately puts out more than my "900rms" kenwood. Alot cleaner sounding too. I was having a really hard time setting gains last night too. I think i need to find someone with an o-scope. Just though I would compliment Sundown for working with me on getting my amp and, though I don't know very much about car audio, I was really impressed with it.

Had to do some work on my system, my MDF speaker mounts had rotted away in my doors, so while I had the car apart replacing them, I decided to also install the SAX 1000D I had bought a year or so ago, and hadn't yet gotten around to putting in my system. This was to replace the Alpine MRV T-505 that I had been using as a sunb amp. Wow, the difference in bass output is amazing, this is almost too much bass. I don't want my car to sound like the typical boom thump that you'll hear in just about every town in America, but right now it does. Bass just completely overwhelms the satellites, even with my bass settings on the radio set at -6. I've got gain at about 60%, not su…

Does anyone here have these components? if so how do you like them and how much power can they handle

http://www.caraudioclassifieds.org/forum/sundown-audio/93918-sundown-yard-sale-updated-8-1-11-a.html * UPDATED LIST TO BE KEPT ON CACO so I don't have to update every forum. As of this morning : I am not interested in re-building ANY of these items before shipping them out due to time contstraints -- refer to a service like FixMySpeaker or your favorite custom builder for that -- I can ship directly to either if you like. * TRF Motor and Basket - $350 shipped in continental 48 states * MINI NEO MOTORS - $250 each shipped in continental 48 states * One is built as a sort of rigged up 8" for some testing we did * These are XBL^2 enabled motors made for 12-layer flat co…

Any one know what the 1500s strapped will put out at 2.8 ohms strapped? I think I'm better off at 2.8 strapped than .7 with a lowered gain.

Newest production run arrived a few weeks ago -- we changed the output FETs to the same parts the newest 3500Ds are using (more powerful) and made a few other small tweaks. 0.5 ohm performance is now just as good as the v.1 1500D while maintaining the slightly better 1 ohm performance that we had already achieved on the v.2 model. I don't have any 1500D v.1s around the shop right now so I'm using previously tested data : 1500D v.1 POWER : 1970 Watts AMP VOLTAGE (measured) : 49.25 V AMP CURRENT (calculated) : 40 A ACTUAL IMPEDANCE (calculated) : 1.23 ohms SUPPLY VOLTAGE : 12.85 V 1500D v.2 POWER : 2030 Watts AMP VOLTAGE (measured) : 47.4v V AMP CURRENT (calculated) : 42.…