Sundown Audio

My SAX 1200d just got shipped today from DB-r I can't wait to get home from my deployment to install that bad boy I believe my Fi BL 15 is going to LOVE it. I just had to share!!!

Finally got everything in, and it is DAMN loud! Box will stay bare MDF until I get my Sundown SAZ-3500D, as its a pain in the ass to pull the box out. Setup did a 148.2 @ 50hz, even though I peaked @ 42hz. Problem was I did not have any other tones on hand, so obviously this setup is doing more than a 148.2. Hopefully next time I can get accurate results

Anyway to go around clipping feat on sundown sax 200.4 Volume 25 then cuts off

TC Sounds OEM 10" Drivers (2 of them). Enclosure will be built next weekend. Here are some pics. Side By side with TC sounds oem 10" (left) and a Diamond Audio D1 10" (right) both dual 4 ohm.

Hey everybody, I just purchased a USED SAZ 1k on here. And once i installed it i realized that the blue l.e.d on the amp was not on. I checked the voltage and it was reading over 14v. Checked the grounds, power and it was all fine. I even swapped out the amp with TWO other amps and the others worked fine. (nothing was changed). The amps used were a Sundown 100.2, and Alpine MRP M1000. Now after trying one more time i was messing with the remote wire and saw that the PROTECTION l.e.d would light up from time to time. So i am guessing that the power l.e.d. is just out which is no big deal, I cannot confirm this because I dont have a working woofer sitting around i …

My new 15" Nightshades were delivered yesterday and I am quite happy with them already! Thanks a bunch Jacob! Sorry if I came off a little anxious... but I was anxious lol Gonna be working them in over the next few days to loosen them up a bit for the show this friday Happy like a little kid in the candy aisle. Happy to represent Sundown, I'll do my best! Time to Break them in! Still have tons to do before the enclosure is finished but here is what it looks like with NIGHTSHADES!! Rubber gaskets are just laying on top of the subs in this pic.. still have to get the tnuts in.

Hey guyz I'm about to order an saz 1500v2 could I strap another saz 1500 that's a v1? Is that ok or will they go kaboom? Thanks

Ok so in the manual it loooks like I have to connect both positive speaker out terminals to the + speaker and both negative to the speaker negative to run it bridge... is that correct? On my other amps it was always the positive to speaker A + and the negative to speaker B negative

I made it here safe ..........

Pictures from the factory : I will be going with a rubber gasket for production. Hoping to have this prototype soon... it's been delayed a few times.

My new SAZ-1500D (Jacob, you're the best!) came in via UPS today. It just occurred to me that nobody has posted pics of the new heatsink for this model, so here you go! This is a crappy picture, but it shows off the upper heatsink.

Heard one tonight... Wow. The owner was Toby from T&J Elite Customs in Oldsmar, FL. Was in an Escalade, probably an 04 or so. Was a SAZ-3000D running a Critical Mass 5000 in a box that was around 3 cubes tuned to 38hz. SAX-100.2 on the Critical Mass comp set. Entire system was 1 12, 2 6.5s, and 2 tweeters. Those components screamed! They sounded great, and blended perfectly. The sub was probably the best sounding woofer Ive ever heard. Couldnt even tell there was a sub, you would think it was actually a bass drum. As good as it sounded, he metered it and it was right at 144.xdbs on the Termlab, legal. He is a Sundown dealer and was playing with the 3000D and hooked it…

PRE-SALE ORDERS ARE FINAL - THERE WILL BE NO REFUNDS -- If you are not 100% sure you will be financially stable then don't pre-order. THESE WILL NOT BE IN UNTIL AROUND the end of April to early May. DO NOT pre-order if you are in a rush or on a dead-line -- as always there can be delays with pre-orders. Just want that to be clear. --- PRICING: $1200 each SHIPPED in the continental USA TO ORDER - Paypal me @ [email protected] Regular price is $1549 MAP / $2149 MSRP. --- Rated Power : 4500 x 1 @ 1 ohm 2000 x 1 @ 2 ohms 900 x 1 @ 4 ohms TEST RESULTS: 3100 Watts @ 1 ohm nominal rising to 2.67 ohms on 14.4v dropping to 13.6 volts 4650 Wats @ 0.25 ohm nominal rising to …

Ok, so ive been doing some subwoofer research, and i want 2-3 subwoofers that will give good sound quality and also output. I figured 2 or 3 of the SD models. Anyways ive stumbled on this wicked site offering 75% off: http://swspakistan.org/subwoofersa.php?id=new-sd2-10d4-sundown-audio-slim-mount-10-dual-4ohm-subwoofer-shallow-sub-p-11839.html?zenid=2a5e2cbc3a9ee40920f158e6edea1914 Does that seem legit at all? They asked for payment in itunes giftcards after checkout lol. I have no clue what to think about this website. I suspect it may be counterfeit or they might take the money and run. Anyways Im pretty sure its not a legit Sundown audio dealer so i wouldnt be …

I have 4 X8 V.2 D4's in a ported box. Im looking for advice on what amp to use and should I drop them to 2ohm? And should I run them off of 1 amp or 2. And what amps are recommended. Help me OB1.

I have a prototype SAE-100.4 on the way with my 1200D shipment... here are a few pictures of it to share : It features a new double sided board design like the SAE-1200D v.2 does. Crossovers are very basic as it is an SAE model and it is also made in China alongside the SAE-1200D. This will NOT replace any SAX multi-channel models... it is simply a part of our lower cost SAE line. There is NO ETA YET... price is also pending.

Okay i have been running a 1500d on 4 10" kickers while i wait for my sa-10's . I had another 1500d in closet, so i decided to go ahead and throw it in,and get it strapped, and ready for the sa's . Heres the deal i had the gain set all the way down so as to not destroy the kickers. Added the second 1500d, and now i can set gain to almost 3/4 and its still not as load as with just 1 amp the single was running 1ohm and the 2 was at 1ohm strapped so .5 each. voltage doesnt drop thats not a issue i just cant figure out why its louder with only 1 amp running if 1 was bad it wouldnt work at all strapped? or could that be a problem?

so i am new here just kind of feeling out a system for my daily driver(91 civic hatchback) i want to keep the rear hatch for the most part seeing as i do take my kid in it sometimes and have to randomly carry little stuff back there so i was thinking either 1 of the sa-8's in a t line(really want to build one they look sweet) if i have the room i know they can get to be pretty large or do 2 in a box around 1.5 cubes i will be powering what ever with a planet audio big bang 950 so 650x1 at 2 ohms that should work really well on a single or a pair. keep in mind i am not trying for huge numbers just something cool that make people go wtf 8's no way and be decently loud. any …

Phone hours will be 8 AM - 2 PM minus 12-1 for lunch the rest of this week (has been this way for a week or so already) -- but will be back to normal next week. We've had to work around a bit of an odd work schedule for a bit but we'll have it back to normal next week

Looking for suggestions on which sub would be better suited for my situation. I have right at 6 cubes after all displacements, figuring on 82 square inches of port tuned to 33hz. Power will not be an issue with either sub, current plan is one or two PPI Black Ice 1800s. Electrical will consist of 270A alt and 2 D3100s. Going into a very well deadened 99 Ram Quad Cab. The reason for the limited space is I'm attempting to keep a small seat area on either side and run the enclosure centered on the back seat, seat bottom to ceiling. With that setup the only wat I can realistically pull it off is to have both sub and port forward. I figure I'll center the sub between the front…

This was to be a week of catching up on e-mails BUT the container of SA speakers showed up about a week early so we've spent the week unloading, sorting, and shipping the SA woofers. I've done as many e-mails as possible during but still have over 100 messages to do. If I can wake up early one day this weekend before my family I'll try and tear through them and get everyone taken care of. Thanks for the patience guys !

Everything was working fine last night. This morning i turn on the car and i can hear static coming from the woofer. I figured it was the subwoofer coil rubbing or something. Well i try 2 other subwoofers and i get the same result. Everything seems to work fine except there's static that kind of sounds like rubbing styrofoam together. I tried everything to rule out other components and still the same result. Strangely enough the amp works fine apart from that. So i have no clue what to do now. Do i just send it in to get repaired or what? I never thought i'd have any problems with it. Any help would be appreciated.

Coming back from a snowboarding trip almost home and system shut down. Fuses are fine but amp is not turning on. Light is not turning on the amp.

I bassraced. Got a horrible score... 151.5. Kinda crappy start, almost 120 degrees at the time, drained batteries, warm subs, warm amps.... The amps were screwed basically. I didnt play it once the entire drive there, for like 30 minutes, or at all that day even. After that ride with the amps just in the heat, they were burning up. People who I see bassrace a 153.5 no problem at all had the hardest time you could imagine break 150 in bassrace. My amps are also set to be safe. Gains less then 1/8 up, with SSF set way up to like 40-45hz. Its set to not blow anything up, but Im guessing that when I tune and tweak them Ill gain a good bit. It wasnt a good day for anyone. Well…

Hey, jacob or whoeevr is helping me out here, i need some input on the voltage im looking for on my dmm to acheive the full rms. I need some clarification on if i did the calculations right. 1st my sub amp, i running it at 1 ohm load to get the rated 1000 rms. so i would do sqrt(1000*1) = 31.6? 2nd (part i don't get) when i run my 100.4 bridged to 2 channels at 325 rms @ 4 ohm load, how do i do the equation? is it sqrt(325*4) or sqrt(650*4)? so would it be 36 volts, or 51 volts? I found it really outrageously high for the 100.4 to have a 51 volt supply when bridged, so i hope i right at guessing its 36 volts per channel bridged correct? Also, would you recommend runnin…