Sundown Audio

im considering 2 SA-12's sealed 1.5 each off a sae-1200d. This sub work well sealed? Im curious about xmax specs on them.They seem VERY well built which is one of the reasons they are a top choice atm

received a replacement 1200d over a month ago.its been installed about a month.i set the gains with dmm and never play my system hard usually only play to and from work.turned it on this morning,and no sound.so,i got out the car to check my amp,and noticed the power and protect lights are both on.haven't done much testing yet besides disconnecting the rca's and sub wires to find both lights still on....any suggestions as to where i should try troubleshooting this problems?thanks in advance

I see there here in the SSA store but say pre order on them still. How would i go about getting my hands on 2 of these subs?

i have two 3000d every time i try and turn up vol one of the two go into protect its not always the same one . they are running 1ohm each i am also running 3 lifeline batteries 1 d3100 and 1 stinger 1700 225amp alt voltage drops to around 12.6 any help would be great i do compete would be nice to be able to keep it playin for good numbers

Is there anyone in the Dallas area that can build me a box for 2 Sundow SA -12's?

I know this is backwards of what most people ask, but I cannot find it documented anywhere. I have limited space, and I'm trying to upgrade my system using the equipment I have sitting in my garage. So, that would have me using 2 channels of my 100.4C bridged - running a single SD-1 10" sub...which is an 8 ohm sub. So, what I'm wondering is how much wattage I will be able to get out this amp at 8 ohms bridged? My guess, based on the published specs, would be in the neighborhood of 200 watts. Just looking for a confirmation of this. Thanks!

What does the saz-3000 bass knob control and how does it control it? Is it gain or boost? does it override the amps settings or does it max out at them? BTW great amp, My car on score is only .6 db louder compared to the car off!!! I was amazed by this, helps alot for db drag

I occasionally build custom drivers on non-Sundown platforms by request -- few pictures to share These use the Z v.2 light weight 15" cone, Z v.2 production voice coils, Z v.2 production "2 spider" pack, an additional re-enforcement ring at the triple joint, stock T3 TSS frame and motor. With this cone the factory trim ring can also be used unlike the last TSS I built with the wide roll surround. * Top triple joint * Factory trim ring in place * Triple joint ring between cone and spiders. This cone is a bit shallower so there is room between the cone and spider. * The second one being built... this is my spider press rig to make sure the spiders stick well to one ano…

I have had my 3500D installed for a while now and its great however when I really crank it up full tilt on music after maybe 20 mins. it will sometimes go into protect. I had a 300 amp circuit breaker hooked up next to it up until today when I switched it out for a 300 amp ANL fuse. I had a problem with the circuit breaker tripping when turned to full tilt also, I think due to extreme vibrations. After replacing the circuit breaker I found it still went into protect once today. I have 2 165ah batteries next to the 3500D and a optima yellowtop under the hood, but I'm still running the factory alternator which I plan to upgrade soon. I have a digital gauge mounted on the da…

Hey guys I have some fast questions to ask!! 1. Lets say I used 8 gauge from amp to sub box terminals, then 2-12gauge runs from terminals to subs(yes 2 subs)? What I want to do is run 8awg from the amp to the terminals then from there 2 runs of 12gauge, 1 run per sub. I think this will work b/c 8awg can support 75amps and 12gauge can support 40amps (since 2 runs40x2=80amps) since there is 2 runs which will be hooked in parellel and in parellel we know current divides up I should be okay? but wait in parrel each run will see the same voltage of... o well input is needed here lol! the currnet which the 8gauge will see will be a peak of 50amps. I ask b/c i have a ton of 1…

I was just wondering what store actually has some of these in stock.....Looking to upgrade from my Type-Rs and I believe this would be a good upgrade...What are you guys opinion???

seeing as i finally decided i want to wall off my truck, i need a few opinions and specs. i was wanting to know if a 14^3 box would be to big for 2 18s. i want the box tuned super low, and i've already done some calculations, and with a 14^3 box and the 4" ports i already have made. it would tune the box to 22-23hz. so the other thing i need to know, is what do one of these subs require for port area. with 6 4" ports, i have around 75^2 inches of port area. would this be enough? or do i need to go with bigger ports?

is there any z. v1 15inch d2s left? its beem a little while since ive been on here so im curious thanks

Interested in a used SAZ 1500D in good condition. PM or email ([email protected]).

I know this has probably been answered before, but the search bar is pretty much useless on this forum. So if I can keep my electrical system from dropping below 13.0-13.5 volts, how will the saz take the .5 ohm load?

Okay so im going to buy a whole new system in a year or so but for the mean while i have 2 kicker CVT, a boss amplifier 1600 watts peak, a optima yellow top battery this is all in a 4 door F-150 2007 under the back seat except the batter, and i fell like its not loud, is there any way to improve, it i have the factory radio i dont know if that plays a factor i dont think so but if any body knows how to improve it please help me maby theres a way to port the box or something

Since my van is known as just a burp vehicle, and I really have been wanting to see what it would in Drive By. For those that don't compete in MECA Drive By is measured with the sensor 54" off the ground and 6 feet away from the passenger door, 30 sec, average no test tones. Mids and highs must be heard. So.... who wants some result?

I'm going to build a ported box for two and need to know if the ported box volume spec (0.6 cuft tuned to 30Hz) is net or gross.

I have gotten my nightshade from fedex yesterday. Had it reconed from a twelve. I would like to say it looks excellent and you can even smell the new sub smell. Haha thank you jacob for your help. Jordan Hughes

Ok maby what i should of asked was is the t2500 from Rockford enough to power a fi btl 15" to full potential

I bought a used ns motor on here but the screw to attach my new 18 basket to the motor i dont have. dose anybody know the thread pitch and diameter? i dont really want to haul this motor around the hardware store trying to match sizes. thanks guys

So Derrick came up today and constructed a box for me for my four SA-8s... still two 1500Ds on one Stinger SPP-1500D and one Stinger SPV-70 battery on Powermaster Charger (car off). We built the box from scrap 5-layer pine plywood for testing... we plan to use birch ply for another version at a later date. Results here :

I'll be making a thread later on to explain WTF happened and call for your help. For now just a picture, so if anyone has seen it on some other forums, write or PM me. I don't know if they are so dumb to leave the signs but... My baby...

Put the two SA-8 box in the CRX modified with an 8" aero-port... finally got tuning settled in to 57 Hz as the loudest. Powered by two SAZ-1500Ds... with one Stinger SPP1500D and one Stinger SPV-70. On Powermaster charger for testing. Interior of car is currently gutted to prepare for sound dampening. Here are the results : Score is dB Drag style on the dash legal and sealed up. Little FYI... bought the ports here : 8x20" Flared Ports NEW big raduis

Dont really know what amp to buy im bearly gona start building and was wondering if i should go with the rockfosgate t2500 or sundown SAZ-3500d money not a problem , oh and im going to be running one 15 fi btl havent bought it nether nor sure if to get 1 ohm or 2 ohm some body please help me.