Sundown Audio

Will 2 15" SA 15s have enough room as of specs in a ported box that is approximately 36" long, 18" deep and 24" tall? Just wondering because I would like to put two 15s in the cab of my 98 s10 extended cab.

What would be the best way to hook up 3 1500's to 6 Sa-12's. Can they be strapped together? Can I use in a master/salve if I put 2 Sa's on each one? Each amp will be running at .5

As some of you may know, I am the one who had the first pair of Nightshades delivered, thanks a whole lot Chad and Jacob. I've run into major financial problems and I need a little bit of room to breathe. My subs are the ones pictured in most of the earlier threads from Chad. The subs are still in mint condition and were only hooked up for a maximum of 3 weeks due to amp and now engine problems. I can post more pictures but as the title says, 15" Nightshade D2. PM for price team mates only. Thanks. -Matt

Setup: Car: 2002 Chevrolet Cavalier Battery: Purple Haze Deep Cycle Wiring: 1 run of 4 guage monster to the back to 1 farad cap, split into 2 4 guage runs to amplifiers Amps: 2 SAZ-1500D's strapped Subs: 2 Oldschool ClifDesigns 12" 1000Watt RMS wired at 3.2 ohms. Box: Bassworx prebuilt futureshop Deck: Pioneer Premier DEH960-mp First run (Qualifying): 139.1dB TL ran from 30-41 hz, hit peak at 41hz. Second run: Started at 42 Hz, ran to 139.3. Amps went to protect and had to reset deck with time clicking (while tied with other competitor). Reset deck and hit a 139.8 at 43 Hz. Third run: fudgeed it up, ran it burp at 43Hz for a 140.2 when the LED's started the run. Other…

Just finished unloading... will ship pre-orders next week as they all must be tested. I am very happy so far with how they turned out -- hope that customers enjoy them as much as I think they will ! If I ever get time I may drop one of these in my Jeep and see if I can still do a 150 with one of these 15s *laughs* Would be fun to try at least.

this is part of my new sq install which consists of a premier 880 prs head unit morel hybrid ovation6 set RE XXX 12 the install inst complete yet but , i just couldnt wait to post it ... any feed back will be appreciated the laser etching was pretty cool to watch ... took about ten minutes and was totally worth it ... cant wait to light it up with blue l.e.d.`s

need new amp. quick question.... how would it hold up @ .7 ohms? with, 230A alt, Yellow top under hood, Kinetik 2400 in back, 1/0 under hood & back, second run there but not hooked up, It's either .7 or 2.8, two Quad .7 coil subs... TC-3000. I could do two 1500's @ 1.4 ohm each I guess... but I rather like the idea of one big amp... Ideas?

well yesterday i went to install my sax 50.4 and the amp turn on but when i hook up my speaker there was no sound. Well then today i went to turn my radio on to power up the amp and it was in protection mode but when i unhook my rca the protection mode goes away but the blue led doesnt light on when i unhook the rca

Well guys I finally did it. I broke 150db. I got a 150.7db @ 36Hz in the passenger kick with a TL and drivers door open. USACI Modified 1001-2000W Vehicle: 2002 GMC Envoy Subs: (4) Phoenix Gold Ti12d Elite Box: 11 cu ft @ 28Hz behind "C" Pillar Amps: (2) Sundown SAZ-3000d stapped using a Maxxlink @ 2ohms HU: Pioneer DEH-P940MP

Alright so i get my sae 1200D and 12" fi bl installed saturday. drive around for 30 minutes and love it. stop to eat for about 45 minutes. when i come back and try to turn it on the sub makes a weird noise and the amp goes into protection mode. restart the car a couple of times and it does the same thing. take it to the place i got it installed and they rewire it and it still goes into protection and they hook up an alpine amp and the alpine works fine. so do i send it back? or is there some other way of fixing it?

im considering 2 SA-12's sealed 1.5 each off a sae-1200d. This sub work well sealed? Im curious about xmax specs on them.They seem VERY well built which is one of the reasons they are a top choice atm

Started in on the install.. Wish I had more ground cable, we decided to do multiple runs and I don't have enough grey/silver since we used some for more power wire.. doh. It'll all be hidden anyway. Lots more to do (probably a couple more days worth).. I'll keep the pics coming.

The molds completed a few days ago and the first samples rolled out -- here are a few of the first look photos from our basket manufacturing company! I am super excited about the potential these will bring to out larger woofers. Once our new spiders, cones, surrounds, and spacers are all tooled we can really show off what these are capable of -- those parts should have completed samples as well soon too. These things carry some serious heft... the base plate that bolts to the motor is 9mm thick un-painted compared to 5mm on most 4 and 12-spokes and 8mm on the Ti-18 frames (add about 0.5mm for paint). They are the strongest frames that I am aware of ever to be produced. --…

I recently just purchased a set of Rainbow Germaniums (150w RMS) and a Profi 12" subwoofer (DVC 2ohm - 50~350w RMS). Currently I have eD amps in my car (9.2 & 9.1) and I've heard alot of great things about Sundown amps. The SAX-100.4 caught my eye after seeing pictures of it, but not sure if it's gonna work with my setup. If I run Channels 1-2 to my Germaniums and have Channels 3-4 to my sub (needs to be 2ohm if possible), would this be a possible setup?? I know the Germaniums will not get the power it needs @ 100x2, but if I bridged the 100.4, then that is way too much power for them. Also, how many watts will the Profi sub be getting if I bridged the rear chann…

Sundown's website just got a major over taking. Switched over to a new platform. Great looking product pages, FAQ section are just starters for this. Check it out and see what you think! Brought to you by: LFTNdesign http://www.sundownaudio.com

So to make a long story short I have a polk amp that puts out 573 watts rms. The rated rms level for the e 12 is 400 and my amp can't even push it. I don't know if it is because the sub hasn't broken in yet or if because this sub is simply a Badass. Anyway the point I am trying to make is... Thanks Jacob for making a beast subwoofer. Now just time to get a more Badass amp to push this bad boy.

just lookin to make my door speakers loud i wanted to just grab a 100.4 for all 4 doors or will there be any difference if i use two 100.2's

Just finished wiring up my car and I'm kinda confused about the settings on the amp. Heres my setup: SAX 100.4 (#1) Bridged 1&2 = Left Mid Bridged 3&4 = Right Mid SAX 100.4 (#2) Ch 1 - Left Tweeter Ch 2 - Right Tweeter Ch 3&4 = Saved for future sub Ok from my previous installed with a Pioneer Premiere 860MP running actively, I know where I want my Xovers to be at, but I just dont know how set that on the amp. Its been four years since I last setup my system. I recently swapped headunits to a Pioneer Avic D3 and now will be going passive. Heres how I had it set on the 860MP: Low : LPF=50Hz Mids: HPF=63Hz / LPF=2kHz High: HPF=2.5kHz How would I adjust thos…

2-SI Mag D2 12's and 1 SAZ-1500D Here is the link to some testing we did for the NSPL Comp. tomorrow. Thank god Jake was there to stop us from using 2-1500Ds last night.........we would have hurt something!! Hope yall enjoy:) Nikki

I received a brand new Sundown saz-1500 this week and I just got around to installing it. All I can say is wow, it pushes the heck out of my RE SE 10 d4. It's funny, this is only giving the sub about 800 watts since it's running at 2 ohms. In addition, I have the gains on the amp turned way down, as I have not had a chance to set the gians properly yet. I think it's going to be time to get a sub that, first of all, can get to a one ohm load, and secondly, take the 1500 watts. That amp is a beast. I'm excited lol. I also received a Sundown sax-100 today for my highs, but I have not had a chance to install it yet. All Sundown as far as my power goes. I am converte…

Hi all, I've read here and there not to use the bass boost( because of clipping signal?). But, if it is so bad, why do we have it on the Sundown amps like my saz 1000 D ? How and when to use it? Mine is still set to the minimum, and my 15" Icon seems to love it:)!

I just moved to west sac and went to a dbdrag show and I didnt see one person running sundown.seen a ton of DC stuff wow do they like dc here. I'm looking to start an s10 build SSNW in an s10 reg cab and was thinking about running some more sundown.what do you think? going to start small couple of 18's and a single amp for now. but i have to find the right truck first.

Here is a link to the beast in a bass race

Alright, my 2 amps came in. My kicker amps never had this many controls, so I'm going to need some help... How do I hookup the RCA's on the 1000D? Besides the gain, how should I set the other controls? Why are there 2 speaker terminals if it's a 1 channel amp? Which terminals do I use for a single dual 2 ohm sub? How do I hookup the RCA's on the 100.4? ...All the controls? The manuals say practically nothing. 1000D... 100.4... If you need a better picture of something please let me know.

Leaving today after UPS picks up... will not be doing much e-mail while I'm gone, just a heads up