Sundown Audio

Im either wanting to pre-order the saz-1500d v.2 in the next day or two for 400$. Or I was looking at the Saz-2000d in the B-stock Refurb section for 400$ and have a little headroom. Power is going to an XCON by the way. Any input is appreciated.

This weekend i wanted to see what the Lb Moab XxX 15" would do in a Street beat boxx.. 149.3db @ 44Hz was thats 1 sub w/ 6000watts rms / 7cf box ported to 36Hz

Well my sa-12 stopped working and I took it out of the box and found this black stuff Idk what it is Is this normal to break and can you fix it? I didnt even have it installed for a month.Help somebody

Every time i start up my car, the sundown starts up but then goes straight into protect. I have the SAZ3K. I used an additional head unit to make sure it wasn't the signal. Without the RCAs plugged in and without the speaker wires plugged in it still did this. Here is a picture of the only thing i could find WRONG internally in the amp. Its also really loose when you go to touch it. Thanks for the help, Curt

These are actually of a proto that was shipped in December to Mike (theothermike). He was nice enough to share with us!

So the 1000 is rated at 1000W @ 14.4 volts. What kind of numbers are we looking at closer to voltages on stock electrical, say 13V? Would two 1000d's be content on an 100A alt, with the big 3, and a battery in the rear? Also, one amp does 1000W, but two strapped does 1800. Why is this? And one more question... would a 1000d on a Fi SSD 12" wang awesomely? Thanks! -Trevor

I have 2 ns v.2 12's D2 and 2 3500s strapped to 1 ohm. How ballzy must 1 be to strap to 0.5 for 0.25 each? Would there be a good db gain?

Would a Nightshade recone fit in a SSA Icon motor?

Alright, my 2 amps came in. My kicker amps never had this many controls, so I'm going to need some help... How do I hookup the RCA's on the 1000D? Besides the gain, how should I set the other controls? Why are there 2 speaker terminals if it's a 1 channel amp? Which terminals do I use for a single dual 2 ohm sub? How do I hookup the RCA's on the 100.4? ...All the controls? The manuals say practically nothing. 1000D... 100.4... If you need a better picture of something please let me know.

sup forum. I'm wanting to upgrade my front stage . i have a saz 1000d with an icon 12'' box built to specs. i'm leaning torwards rainbow slc 265.25 since my id CX.62 v2's blew ( friends borrow + drinking = blown ) the amp i have for them is a cheap performance technique. i was wondering if the sax 125.2 is good for frontstage.. simple question but i want to confirm before spending $$ thanks!

im considering 2 SA-12's sealed 1.5 each off a sae-1200d. This sub work well sealed? Im curious about xmax specs on them.They seem VERY well built which is one of the reasons they are a top choice atm

I can't wait to get them in and installed! It's been quite a while since I've done any car audio and I'm pretty excited to get back into it!

Will 2 15" SA 15s have enough room as of specs in a ported box that is approximately 36" long, 18" deep and 24" tall? Just wondering because I would like to put two 15s in the cab of my 98 s10 extended cab.

Vids are off my cell phone. name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src=" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344"></embed></object>"> name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src=" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344"></embed></object>" type="application/x-shockwave-flash" wmode="transparent" width="650" height="535"…

Hi all, I've read here and there not to use the bass boost( because of clipping signal?). But, if it is so bad, why do we have it on the Sundown amps like my saz 1000 D ? How and when to use it? Mine is still set to the minimum, and my 15" Icon seems to love it:)!

I'm planning to run 2 sax-100.2s and 2 saz-3000s strapped at 2 ohms. I have a 200 amp excessive amp alt and i'm attempting to make a bracket so i can also use my stock alt but i'm not sure if i'll succeed in that. Is it recommended to run 2 alts with 2 saz-3000s or would my one 200 amp alt be fine? I'd like to limit the amount of batteries to 1 under the hood and 3 in the back. I'm a little tight on space. Is this alright or would i have to use more? My last system consisted of 2 saz-1500s. Using my 200 amp alt, 1 battery under the hood, and 1 in the back I didn't seem to have any problems at all. Just wondering how much i need to upgrade my electrical to handle 2 saz-300…

Greetings currently own a z v.4 10. It is a 97 Tahoe being ran off of a saz 2500 v.2. It would be more cost effective to re-cone it to a 18". it would cost little over twice as much two add another z v.4 10, but just because it cost less doesn't mean it will sound better. basically I'm after more output. better low end extension. I had it in my cutlass and it sounded great but in the Tahoe I have a lot more cabin space. any suggestions between the two? thanks in advance for the input.

Hi everyone, I know I've read something about it but I don't remember where, and I can't find it ! One of my friend is running a 15" D1 xcon sub with 2 Sundown saz 1000 d strapped at 2 Ohms. He uses the gain remote. Now he's planning a new build with 2 subs and 4 saz 1000. 2 amps per sub. He will have to use 2 remote, and only wants one. What can he do , what to buy to have only one remote to control the gain on the 2 (2)amplifiers ? Thanks for your help

Got my new toy in today....pictures dont do this thing any justice..at all... Insanley massive......Makes me want to order another one.. I got gain and bass boost at 1/4 and its slamming already....I can not wait to turn it up and see what it really does..but at 14/35 on the volume...the lows are crazy..... Gonna break it in for a few weeks at low volumes though.... Powered by 1 of my SAZ 3K's and 3 DEKA's..... Thanks for a bad ass sub Jacob.....was packaged great to...arrived here in top notch shape. Will post more pics in a short while...as well as a video...

whats up, i was wondering if i could get the recommended cuft for a 15 inch nightshade. the thing is im planning 4 15 nightshades in a wall, but only will have a little over 10.4 cubes after discplacements, so around 2.5 per driver. or do you think i should just do 4 12s in that space, which do you think will get greater output. and this will all be powered by 2 3000ds 2 3800 kinetiks and iraggi 260amp alt.

Just sent [email protected] the money. I can't wait to get this and set up my fi q

Can some help me with dimesion for an slot-ported enclosure, for one sa15.I have a 2004 Buick Regal.I'm planning running 750rms to this subwoofer. I need all cut pieces.The height has to be 16' OR LESS.

Went to get my brand new SAZ 1500D installed today but when they hooked it up it wouldn't work. The amp turns on and gets hot but won't play. They took it out and put in a jl amp and it played great. They also hooked the amp up to some machine (forgot the name) to see if it would work and nothing is there anything I can do or do I have to send it back? Oh and I'm running 1 12" fi bl in a 2 cuft box tuned to 35.5 hz with 0 guage wiring

so there's a show this weekend. getting tired of everybody talkin stuff about my sundown audio stuff cause they never heard of the name. i need to change my setup so i can win this show. my box is about 3.3 with 3 of the dual 4 sa12s. i running a 3000d @ 2.6 i have two options. either port my box i already have to stay behind the third row. or flip the seats up and build a 6 cube ported box just for the show. if i port my box i already have how high would i need to tune it. i need a mid 140's for this weekend. last show they held guy won it with a 139 or something. and i might add he had 4 15s in a box not tuned for the speakers. also would it be safe to wire it in par…

Something we are working on... Was designed around the needs of our NEO-8 project : Project I'm Working On - Car Audio Classifieds But will eventually find it's way into other projects... I've started a new Ferrite 8" design to be used with this frame... depending on the cost / performance may move up to X8 designation (based on motor the size of the SA-12). It is a bit over-sized from a standard 8" cut-out and OD but that was needed to get a large spider on an eight finally ETA not set yet... but keep your eyes out !