Sundown Audio

Okay, I think I have it done, my electrical will consist of a 300 amp alternator (Iraggi), A Powermaster S1200) up front, (2) D1200's for the trunk, all wiring for batteries and amps will be 1/0 ga., Subs will be (4) of the SA-12's powered by (2) of the SAZ-1500D's. This is all going into the back of my 2001 Camry, with the box designed by banginAltima (as soon as he's done) so hopefully the Mad Scientist of SPL (Jacob Fuller) will be proud of me

well team carlisle acoustics/ team sundown audio went to E town today and i believe we made a good showing. 1st palce STREET 2 - Derek "me" with a 147.7 @ 34hz SPL in my VOLVO 2nd place MOD 2 - Jeremy with a 149.9 1st place DRIVE BY 2 - Jeremy with a crushing 128.4 1st place DRIVE BY 1 - Corey with a 121.9 and i believe Seth was in 3rd place in AS1 cant remember his score We should have plenty of pics to post up as well.!!

ok i have no idea how to wire subs off the top of my head, i have just used charts. i have gathered 2 diff wiring picstures for wiring a 2ohm dvc sub down to 1ohm. one is from rockford fosgate and the other is from the jl audio website. they show different ways of wiring it. where do i go from here?

So heres what is on my mind. First off i am wondering how to wire a subwoofer down to a one ohm load due to there being two sets of speaker terminals. Maybe a noob question but i cant figure it out. Second and this mite be harder to answer. Will this amplifier overpower a Fi BL15 with with the hyper pole upgrade or would it be able to take the juice without messing anything up? Any elightenment would be appreciated.

What would be the power output of this amp at a steady 14.4volts at 1 ohm? And what battery would u recommend from powermaster?

havent seen any available on SSA site. just wondering where can i pick up a set of 15"s. just preordered the 3500d lookin for something that can hang. also order 100.4 need components for that too. i have a set of 3 way components but i dont know if i wanna use them they are 350 watts rms.

what is the mounting depth for them and what is the sensitivity on them? ... how would they do in a sealed box? ... what size sealed box do they typically need?

Well jacob, we did it man, me and 3stagevetch both took home 1st place positions using sundown 1500d's.. 3stagevtch did 149db in advance NW and I clocked a 140.1db in rookie 1 in Iasca. Im hoping on october 5th to raise my score by 5dbs to take the WR in Iasca rookie 1 and I know for sure rene looking to put his set at over 150dbs.. We making the team proud!!!! Das mine^^ heheehehehee

I currently have a pair of SQ XBL^2 10s in 2.4 ft^3 tuned to 32hz. They're being fed right around 500w a piece. They sound great and have decent output but I find myself wanting a bit more. I have experience with mostly SQ subs (IDQ, AA Avalanche, TC2, etc)... how would the SA-10s compare? They'd be used in the same box, with the same power.

First of all I would like to thank Jacob for giving me the oppurtunity to buy his amp! installed The saz-1500 replaced my RFt10001bd, All I can say is wow! this amp had more balls,sounded better, and took less space! I am not the techie kind of guy but for a consumers point of view, the most important thing is that the product gave an improvement,it did not let you down,performed more than expected and most of all you know that you are backed by an excellent guy! The amp is driving 2 12" Oz MAtrix eLite head unit is a clarion hx-d2,seps are Legatia 631 and amp for the seps is an Audison Lrx 6.9. I wouldnt hesitate to buy from jacob again, he is a nice gentleman to ta…

I know most amps have to battle heat to stay running as my last amp use to operate well into the 150 degree range on a normal basis but I just have one question. Wheres the heat at on this SAE-1200D???? Ive been bumping hard for 3-4 hours straight and not even a sweat. I can touch it at the end of the night and the heatsinks drain the heat out of my body. How is this thing suppose to be a normal amp????

I decided to redo the gain setting on my saz3000 without using bass boost. Sub is audiopulse axis I started to set it using a DMM on ac volts along with an ac clamp meter first run gain was at min and i got 31.7 volts and 12.89 amps = 408 watts?? second run higher gain-- 79.8 V, 24 A = 1915 watts another higher gain-- 83.4 V, 25.3 A = 2110 watts another higher gain-- 84.8 V, 26 A = 2204 watts after that run the amp shut off. I checked how much more gain i had and i was amost max. so i turned off the amp, tried it again and i could see/hear clipping so i got confused 2204 watts and clipping, I got my WT3 woofer tester and did an impedence curve. My clamp meter has an AC …

Hi purchased this sundown 1500d and i am needing a lil help with this amp setup. I need to know the difference btw the bass boost and the gain. I am using a stock hu using a david navone loc. Fist of all can this amp take more then 6 volts input voltage? 2nd how should i adjust the bass boost with the gain? I am not doing it right i only can tune by ear and it seems i keep clipping the amp because when i play a song when it hits a low note on the song it bottoms out on the sub pops ect. i turn it down problem goes away. How should i be adjust the gain/bass boost?

Has this amp been tested at 8 ohms? Does anybody have any experience doing this? If so what does it put out?

I have dual 1ohm subs...was looking to do 2-3000Ds strapped @ 1ohm but was told that I would benefit more from 4-1500s. Im still undecided if I want to go with a Atomic 7K or get 4 refurbished 1500Ds. What kinda power do u think Id get out of 4 with a 250amp alt, 2 runs of 2/0 welding cable, 1 Deka 9A78DT up front and 3-9A31s in the rear? Do u think Id get more out of the Atomic or 4 1500s, both are around the same price....(I know this is a Sundown thread but please be honest)

Do you think it would be okay to install a SAZ-1500D and SAX-100.2 like the following pictures? The SAZ-1500D will be powering two TC Sounds OEM 10's and the SAX-100.2 will be powering a pair of CDT Braxial ES-630's. The pics are of a 350Z.

Does the SAZ-2500D come with a remote bass knob? I cant find any pics...

I blew my sa12 and was wondering if this is part of the cone itself? and if i got a recone kit if it would fix this?

what do yall think of the z v2 d2 15 in a spl box tuned to 39 hertz on a dc audio pai 3000.1

Ya ya, my wiring is kinda messy right now but it might not be permant. and yes i know i shouldnt brag about "novice" trophy but it was my first time, and i still hit a 144.3 off two type R's with no tuning jus playin with it. on my btl i hit a 147.30. The guy that got first hit a 147.33 with 4 Type R 15''s. FYI GORRILA DUCK TAPE FTW!!!! at the show still filling the aero leaks on the aero's SAZ 3K btl 18 fully loaded 4.5 cu ft tuned to ....???? didnt have time to correct the aeros.

I had my sae1200 for quite some time. Then got an SAZ1500, planned on getting a dc lvl 4xl, but got a great price on a normal lvl 4, so I went with that and sold the SAZ1500 and started using my sae1200 again. I've been trying to set the gains with my dmm, But I've run into a problem. At first I thought it might be the headunit, but I switched headunits and the problem still persists. When I set my gains with the DMM and the subs not connected to the aim, I set it to 30v, which is down slightly from 1000/sqrt 1 All EQ's and bass boosts are set to 0. Headunit volume set to 23/35, sub volume set to 7/15 When I connect the sub, and play a 50 hz tone, I start the hu volume at…

Regular MSRP $349. Special price $225 until end of March! You can order from your favorite dealer OR Paypal me directly at [email protected] Rated power output ----RMS power, 4 ohm stereo 50W x 4CH ----RMS power, 2 ohm stereo 80W x 4CH ----RMS power, 4 ohm bridged 160W x 2CH Signal to Noise Ratio >90dB Low pass frequency crossover 50Hz~500Hz (CH1&2) 50Hz~5KHz (CH3&4) High Pass Crossover 50Hz~5KHz (CH1&2) 50Hz~500Hz (CH3&4) Variable Subsonic Filter 10Hz to 500Hz Bass Boost 0~18dB Variable Bass-Boost Frequency Control 35Hz to 120Hz Frequency Response 10Hz ~ 40KHz (+/-1dB) THD@RMS Watts <0.1% Channel Separation 75dB Fuse Rating…

The amps are in California at the moment from our current update (just now) -- they should arrive at our shop shortly after CES. I know some people have been anxiously awaiting this ! Here are a few pics of a complete product from the factory :

i have 2 fi d1 bl 18's and i was wonderin if it would be better to run 1 saz 3000d or to strap a pair of sundown 1500's?