Sundown Audio

This is the "official" post to be linked in our sticky amp power testing post : ----- This testing done on my Extech True Power meter a full 6-10 seconds in to the burp so we are not catching peak values: http://www.extech.com/instrument/products/...399/380976.html ----- HIGH VOLTAGE TESTING: 6x Powermaster D1000s used for testing 17.9 volts rest - did not measure voltage drop. 10,320 watts from the pair @ 1.5 ohms each after rise starting at 0.5 DCR 5160 each 11,470 watts from the pair @ 1.3 ohms each after rise starting at 0.5 DCR 5735 per amp ----- 12v SYSTEM TESTING: Starting battery + 2x Powermaster D3100s used for testing 3980 @ 0.25 rising to 0.65 @ 11.2v (engine o…

Okay guys... here it is. If you order between NOW and the end of February... $825 for one $815 for two (each) $800 for four or more (each) If you order any time from March 1st until they arrive... $850 for one $825 for two (each) $810 for four or more (each) Paypal me at [email protected] to Pre-Order! The current ETA is around May 11th to May 20th -- this is a rough estimate. As always, with a pre-order the ETA is subject to change based on shipping delays, etc, etc. PLEASE do not pre-order unless you are okay with any delays that may occur. We are expecting around 3800 on a 12v electrical system from these and over 6000 on a 16v electrical system They feature …

The first pre-sale was so popular we sold out before the amps even arrived... so we are doing it again Same deal as last time around! $850 for one $825 for two (each) $810 for four or more (each) Paypal me at [email protected] to Pre-Order! OR Order on our cart system here : http://www.sundownaudio.com/presale/ The current ETA is around the end of August -- this is a rough estimate. As always, with a pre-order the ETA is subject to change based on shipping delays, etc, etc. PLEASE do not pre-order unless you are okay with any delays that may occur. They feature 33% more output FETs than the current 3000D... a quad transformer setup (more efficient)... and some ot…

I have had my 3500D installed for a while now and its great however when I really crank it up full tilt on music after maybe 20 mins. it will sometimes go into protect. I had a 300 amp circuit breaker hooked up next to it up until today when I switched it out for a 300 amp ANL fuse. I had a problem with the circuit breaker tripping when turned to full tilt also, I think due to extreme vibrations. After replacing the circuit breaker I found it still went into protect once today. I have 2 165ah batteries next to the 3500D and a optima yellowtop under the hood, but I'm still running the factory alternator which I plan to upgrade soon. I have a digital gauge mounted on the da…

There are two availible. I know some of you want one of these really bad and we just happen to have 2 availible for purchase. Go here: SAZ-3500D Refurbished @ dB-r $825 each First Come First Serve Thanks! Chris dB-r Electronics

Hey guys, I am sold out of new 3500s... and as of today all of the used ones are sold out. People that are *already* talking to me about them are good to go -- I am counting those as sold. If you would like to pre-order one from our next production run of new amps feel free to hit me up. Otherwise there are none available at the moment.

These are the results we got from my testing today at Modified Nationals in the UK - the first 2010 db drag event in the UK. Single SAZ-4500d amp 0.35 DCR. All results true RMS. Deck Volume started 12 - went to 41 of 47 - still clean sine at this point. 77.9 AC Volts 57.2 AC Amps 13.2 battery volts before starting 11.50min voltage over burp. 77.9 * 57.2 = 4455 watts RMS @ 1.36 ohms impedance. Subs were 2 x DC Audio 4XL SPL Motor 18's D1.4 coils all in parrallel. 158.3 db achived at 66hz!!! Well impressed with the amps - need to try some D1.0 recones now to see what difference we get loading the amp down more.

PRE-SALE ORDERS ARE FINAL - THERE WILL BE NO REFUNDS -- If you are not 100% sure you will be financially stable then don't pre-order. No more exceptions. <b>THESE WILL NOT BE IN UNTIL AROUND THE END OF OCTOBER!!!</b> <i>If you want something sooner the 3500s are expected in before the end of August so I suggest getting one of those.</i> DO NOT pre-order if you are in a rush or on a dead-line -- as always there can be delays with pre-orders. Just want that to be clear <img src="http://www.soundsolutionsaudio.com/forum/public/style_emoticons/<#EMO_DIR#>/smile.gif" style="vertical-align:middle" emoid="" border="0" alt="smile.gif" /> In any…

PRE-SALE ORDERS ARE FINAL - THERE WILL BE NO REFUNDS -- If you are not 100% sure you will be financially stable then don't pre-order. THESE WILL NOT BE IN UNTIL AROUND the end of April to early May. DO NOT pre-order if you are in a rush or on a dead-line -- as always there can be delays with pre-orders. Just want that to be clear. --- PRICING: $1200 each SHIPPED in the continental USA TO ORDER - Paypal me @ [email protected] Regular price is $1549 MAP / $2149 MSRP. --- Rated Power : 4500 x 1 @ 1 ohm 2000 x 1 @ 2 ohms 900 x 1 @ 4 ohms TEST RESULTS: 3100 Watts @ 1 ohm nominal rising to 2.67 ohms on 14.4v dropping to 13.6 volts 4650 Wats @ 0.25 ohm nominal rising to …

Will start shipping them ASAP. These things are HEAVY!

Sold out. Unless you have talked to me in the last day or two and a deal is in the works no more are available at this time. ETA for more not yet set.

So I am looking to pick up my first monster amp and I'm between these two, cause I'm afraid they are going to stop making them. I am aware of the fact that the ns1 has had some problems in the past (mechanically, and shipping related) and that the ns1 is more oriented towards competition use. The SAZ-5000 I haven't heard a whole lot positive or negative or any feedback really at all. Besides the input voltage differences that the ns1 has and it's power difference, what are some differences between the two.

I was just wondering if I have 2 sa8 on a saz1000 wired at .5 ohm will I be getting 1000 actual watts to the sub? I have a 250 amp alt, and odyssey pc1750 battery

going to be running the 100.2 or 125.2 on my 2 sets of PG rsd 6.5" components, so i wanted a matching sub amp. so i figured the saz1000d would be a nice match, nearly the same length in size, etc. so, how many subs should i run off this 1000d, where each sub wont be getting too much power for a daily setup? its for the back of the dakota, its a single cab, so not alot of room at all, thats why im thinking about going sealed, and jacob said they do good in about 0.2 cubes each.

is it possible to get the diagram of the board layout?

I have a Saz1500v.2 that I bought here off SSA less than a year ago. Well last night I noticed my sub just quit playing. After looking at it the red "protection" light is on and it just stays that way. Weird thing is I was actually listening to music on a normal mid level, gain remote knob all the way down and purposely trying to not really hear the sub because I was listening to a rock song trying to adjust my mids. Then when I went to add the sub back in it just wasnt there. I thought the knob was broke but I guess not. Amp was cold to the touch when it stopped working. What can I do from here. Thanks

hi, i have a opportinty to get 2 12w7 ( svc 3 ohm) for cheap ( 500 for both) and i am looking at an amp for them before i get it and i would like to stick with 1 amp for price and i am wondering what does the saz1500d do at 1.5 ohms and also i have a 200 amp alternator. hc1400 under the hood and a hc2400 in the trunk and it is all connected by 1/0 guage wire and the other amps i am going to have 2 eclipse xa4000 amps to give you an idea of the power for the amp. i might add another hc2400 if i can get a good deal on it,

so i just purchased one of the two remaining old heatsink saz-1500d refurbs from chris @ db-r. the shopping experience was great and the price was too good to pass up. i guess im a sundown fan now the hard part is going to be containing my excitement while it gets shipped here to calif.

so my dads drag racing buddy has a car audio shop and he has 2 saz1500d's that need repaired. waitin to here if he can get it done. but would it be cheaper if i got them from him as is for cheap and sent them for repair? if so where would i send them and what would be the average pricing? theres a place her in oklahoma city called toms two way or sumthin like that that repairs all kinds of electronics including amps. would that be a good idea?

Does the saz1500 have a signal output, so you could run rcas from it to another amp? I'm thinking about getting a smaller amp for mids and highs and wanted to know if I would have to run another set of rcas from deck? Or if the saz could output it. Thanks

on a dual 2 ohm sub, what wattage would i see with a 4 ohm load at the amps..... would it be 1600 watts.... 2 ohms per amp..... i know, a little unpractical..... just temporary , sorta just curious.... oh, sorry , two sundown audio saz1500d amps. thanks for your time! chop

a couple days ago my amp went into protect without warning and now it wont come out. i got a hold of jacob already and he said if i cant figure out how to get it out of protect then to send it in. i have double checked all my connections and they are good. i even checked my subs to see if they were blown and causing a short or something but they are fine. im running 0 gauge power wire and big3 and have the amp powering a pair of eclipse aluminums wired to a 1 ohm load. is there anything else i can do to test before i send it in? thanks chris

My brothers kids pre-ordered a SAZ2000d. He asked me when they might be in and shipped? I was the one who recommended the amp so I get to be the one to find out.

hey whats up i have 4 dual 4 ohm subs and want to run 1 amp many people have recomended me that the saz2000d will b .5 ohm stable and i will have to run it at that, will that amp handle that, i heard it will put out like 2300 watts at .5 and b stable thanks

I have had single audiopulse axis dual 2 ohm sub wired to my sundown 3000 at 1 ohm. I was going to get a second sundown for my second axis. but recently testing the power and impedence rise charts with my wt3 woofer tester, i found that my impedence rise is going up to 3 with the single axis. so ive only gotten about 2000watts with lots of clipping. After i noticed that i put both axis's in a sealed box with them wired down to .5 ohms. i clamped it today and took an impedence curve and its raising to about 1.1 ohms now. i got about 2300 watts before my voltage dropped too low where i didnt want go continue, and no one was here to rev the engine. So this brings my questi…