Sundown Audio

The SSA forums would never let me register for some reason. I tried it a ton of times over the past few months with no luck. I tried again today and it let me. Woohoo! So whats up guys?

When can we be expecting the SAX 250.2 and what type of power would it do? .......rms X 2 @ 4ohm and rms X 2 @ 2ohm? and at what fuse rating?

I was just curious if there are any left. I am in desperate need of 1 D4 shipped immediately.......in time for Slamology here locally in Indy. I am gonna call Debbie Monday morning to order but thought perhaps I may get a quicker response here since it's the weekend. Thanks......Chuck McCleery

I have to say congratulations to Gary aka banginAltima for his new personal best score of a 146.9. This was done out of the trunk of his '06 Altima using a pair of RF T1 15s powered by a single Sundown saz-1500d. It is a daily car tuned to 33hz and peaks @ 41hz so no fart boxes here. This car will absolutely pound some Jeezy. This score done with the car completely sealed and mic on the windshield DbDrag style. He is by far the loudest trunk car in his power class. Sundown Powa! I didn't do too bad today either taking 1st in Street Bass (like BassRace) with a perfect 139.9. Yay for cash prizes!

Okay so I got my build done about 5-6 months ago and wired it up and have been running it at .4-.5 ohms with no issues. All of the sudden last Friday it just cut off, no smoke no obvious burn marks. Just went into protect and would not come back out. I know that running it this low can cause issues and so I just went ahead and sent it off to db-r and they think i fried the drive board or the input. My question is can anyone think of what may have caused this. Is it just because i was running it at the .4-.5 ohm load, or can it be something else that i can fix and prevent this from happening again. My electrical is as followed. Big 3 in 2/0 2 250 amp Mechman alts 2 runs…

No its not the toy tractor.... I got that for Christmas. Ha ha... I took an extra decal... Shhhh.... don't tell Jacob. Watch out Trunk 501-1500!!!!

hey jacob, i think you need a lineup to show what sundown has. you have a lot of equipment available and people might not know what all you are offering. i just put down the ones i knew of and the ones i think. maybe you want to sticky it? its just an idea subs: sa Z nightshade monster big boy nsx??? amps: sax 50.4 sax 125.2 sax 100.4 saz 1000d sae 1200d saz 1500d saz 2000d saz 3500d saz 4500d

whats a cheap way to measure my DB'S.

I'm looking for the box plans or ideas for two SA8. Ported or t-line and tuned at what? any ideas.

Well, for all the Canadian people, JordyO from CCA did some testing on a pair of Sundown 1500's this week. And he did a drop test 2 sundown 1500's vs a stetsom 5k at a competition: Thanks Jordy!

Up for grabs is a pair of 10" Sundown SD-1 subwoofers. I used these briefly for testing purposes, they will come with full warranty as they are very close to new. They do have speaker wire soldered to the terminals, though, pretend it's "direct connect" like DD Price is $125 shipped for the pair in the continental USA. These are GREAT with an SAX-100.2 to power them. I am running a pair of 10" SD-1s in my 2002 Civic if that tells you what I think about them

Just wondering if anyone has any pics of the newer style saz1500's.....i think it was the heatsink that was a little different? I know the performance is identical, just want to see how close they are to the 1st ones. I have 2 of the original and am planning on ordering a couple more.

Just unloaded them after lunch; we'll start shipping pre-orders tomorrow. I am really pleased with how they turned out. I wanted to see them before starting more production -- and we sold about 75% of what we got -- so there will be a period of out-of-stock on them; but we should have steady stock starting after the 2nd run !

i only have one sub which is RE SE d4... according to the picture i will have to connect both the positive to the box. and only one to the negative. so from box... it's one + and one -... and from amp it's + - - + So i would connect all both + on the amp and then connect it to the sub. and only one to the negative?

just thought people might want to fallow this one? http://audioforum.termpro.com/topic/28/1200.html

What about be the minimum type of electrical system that i would need to support this. Would Big3, 136 amp alternator, and a powermaster 3100 in the front be enough?

tryng to buy one used or new.

http://www.soundsolutionsaudio.com/zencart...&cPath=3_11 Click the item then click "Write a Review" on the right hand bar.

the SAZ-1500d is marked at 600 at everywhere i look iirc.. are these prices negotiable? because i have had people say they got theirs for 450. if not is there any where to buy used? and what is a good price i should be willing to pay for a used one?

I need some help designing the best box possible for daily. I want the box to be tuned about 33. And this is the space I have to work with - Width - 38, Height 13, Depth 36. I sill did not order the sub yet as I still am not sure on what sub to get. My plans are a 15" nightshade, a sundown 2500d (already own), dc alternator all going in a 2003 Mercury Sable. Any comments or suggestions on my future build would be appreciated. Thanks

So we've had these in stock for a while in Dual-4 configuration; although, I haven't said a ton about them yet since we are awaiting the Dual-2 shipment. Those will be available in about 30 more days. ---------- Specs for the D4 : Specs for the D2 :

Does the new heatsink on the sax-100.2 look the same as the SAE-1200D? Just curious because I thought it would be all black but the one I got today from db-r wasn't.

But jus not sure what to set my dmm on to actually measure the voltage from the amp.. I can take pics of the dmm if that would help..

As the title states, trying to find the displacement on Sundown Z18v.3's. I've tried for the last several hours using google and searching on several forums to get the info on these beasts. Thanks in advance to whoever can help.

Hope everyone had a good one ! I'm back @ work trying to wrap things up as much as I can before going to CES.