Amplifiers / Head Units / Processors / Electrical

IM TRYIN TO REPAIR MY 1000 WATT CRUNCH AMP AND I CANT FIND A PIC OF THE INSIDE GUTS OF THIS DAMN THING IVE LOOKED EVERY WHERE SO ANY HELP WOULD BE GREAT A FEW OF THE DIODS I THONK THERE CALLED FRIED SO I NEED TO REPAIR IF ITS POSSABLE IM NEW TO ALL THIS SO I WOULD LIKE SOME IMPUT THANK YOU OR MAYBE A SCHMATIC ON THIS THING WOULD KICK ASS

just a fast question guys i have an 18" btl fully loaded, i have it running off a saz-2000D. i have my sub wired down to 1 ohm. my question is, should i have my sub wired to the amp bridged or not? right now i dont have it bridged and it slaps hard. but i just saw a vid with the same setup pretty much and his was bridged on the amp thanks an advance fellaz

Should i use a Kinetik 600 Power Cell in my install for my front stage? -- Will it help with my voltage? OR! Will it strain my Alt? I know its only 400wrms.. but i have the Power Cell already. (2) Alpine Type R 6.5 component sets (1) Alpine PDX 4.100 KnuKoncpetz 4 gauge amp kit Yellow top as starter batt. 1/3 Big 3 done. (Batt to frame) Stock Alt -- 80-100 amp (not too sure)

Do i use 1khz for a highs amp? Just want to make sure.Thanks.

Any one able to confirm the dimensions of the saz-3500. I know the sundown site says 660x250x54 but I heard someone say it's bigger than that. Cheers Karl

At one point in time there was a link to a calculator someone had made to just plug in your rms and impedance and get what the voltage ac you should see when setting the gain on your amp. anybody know where that is i wanna bookmark it to my computer. and yes i have already read the sticky on how to set gain. im just trying to get this as a bookmark. thanks

after buying these batteries i found out that they are 34M's and are "starting only". now does this matter? the MCA is 1000, CCA 800, AH 50, RC 100. Did i get ripped? (only paid 100 each) or are they good?

I have an alpine 9886 and pxa-h100 crossover. I've looked through the menus and don't see a bandpass option for an active mid range woofer. I looked around the Internet and didn't see anyone running active with this setup. Did I just not find what I was looking for? Or is it not capable? If it's not then pioneer p880prs here I come. Right now I'm using the passive crossovers with my focal 165a1's woofers in the stock location low in the doors and the tweeters mounted low on the pillars. And powering them with an alpine mrp-f250.

ok so i have a bazooka 500wrms mono im running until i get my saz-1500 fixed.... its running a fosgate power hx2 at 1ohm. its a damn good amp for the brand. i dont know much about it but lately since i got a h/u instead of my mp3 player it goes into protect when the bass hits real low note like on bass i love you for example the real low note when u get major excurssion it goes into protect. is it cause its not 1 ohm stable? gain is about 2/3 up frequency is all the way down bass boost is about 1/4 up sub level on pioneer 680mp is at about -10 thanx in advance

Welcome to NEW ARRIVAL STORE INC Dealers in all kinds of Car Audio/Video, Mobile Phones, Laptops, Apple ipods, Pocket pc, Video Games,Car Audio/Video, Telecommunication Products, and many more,We sell in bulk and as well in Units to wholesalers, retailers and also consumers. We sell so cheap items due to large and bulk quantities we order from the manufacturers to suits the need of our customers all around the GLOBE. Contact Person: Murad Mohammed For Bookings and Inquiries do contact us via... Contact email: [email protected], [email protected] Contact Person: Murad Mohammed Car Audio/Video Price List... Pioneer AVIC-X1BT Kenwood DNX-9240BT JVC KD-AV7001 Pioneer …

Currently I've got a P3002 and two Memphis twelves and a Memphis 15. I'm planning on upgrading my wiring to 1/0, and thinking I'll probably need an upgraded alternator. Someone in another thread said something about needing extra batteries for a T1500, I was thinking I'd be okay with the alternator. Opinions? By the way, I'm planning on ordering a BTL 18 next. I'm also looking for ideas on box design. Its going in an Explorer, so I've got plenty of room. I want the sub facing the roof and the port facing the front. Planning on making a amp rack out of some plexi too, I'll have to post some pics.

I'm about to grab up a normal ANL fuse holder from Knu when I notice they have this "high current" fuse holder that uses multiple mini ANL fuses instead of one big honker like the normal one, (not the mini). They say it will have "lower voltage drop across the fused surface area" as well as handling higher currents. Is there any validity to this statement? Has anyone had any experiece with one of these to know if it really has any great affect on voltage drop? I'm just curious...

Hi Guys, Any recommended Head Unit for SPL application, I'm currently using Alpine 9887 and the buttons fades easily. So I'm leaning towards pioneer for my next H.U. I know DEX-P99RS is the best bet but I can't afford it right now. Any suggestion? My budget is $600. Thanks

okay so i know this might be a noob question but hey im a noob lol. so i want to run 2 runs of 0 guage power to my amp, but they amp only has one input so can i take a normal distribution block and put the two power wires from the battery up front into the the usual out spots and put one run from the amplifier to the input of the block? i will also run 2 runs of ground if i can, i just want to make sure i get as much power to my amp as i can even know i know its over kill. hopefully i can upload this right but here is a picture to help explain what i mean.

So after hooking things up i found that i was short of speaker cable by five feet. I ran down to Mickey Shorr to see what they had. They gave me about 12 feet of 8 gauge power wire for five bucks. so it's a pretty simple question actually, Is there any difference in speaker cable and power wire? can i use power wire as speaker wire? thanks.

Ok, I have been searching and reading yesterday and today. I went back as far as 2007 but I couldn't find any topics like this one that had any good answers. My car will have a Iraggi 180A alternator (biggest that fits my car), BIG 3 with 1/0, 1/0 run for positive and negative from the front to the back and I will be using one Hifonics XX Colossus II and one SS REF4.920, giving a output of about 3800W rms. This will be a daily system, but I will be going to DB drags and other social car stereo events so the car will be competing a little bit and demonstrating the car stereo with the engine off, probably charging with a Ctek 25A charger or using a other power supply. I kn…

Does anybody have advice on what amps would pound 2 15" juggernauts, there dual 1ohm's, my budget is 1600 for amps? there rms is 1500 each

has anyone tried or heard if the soundstream tarantulas are close to tru power or are they crap?

i had needed to get guided in the right direction on purchasing an h/0 alternator. just need to know how big of an alt i need to get to run 4000 rms (2 subs) or 2000rms (1 sub) thanks!!!!

alright, so how would you set up an amplifier to your H/U? thats my main question. if i post a picture of the amp i want, could you tell me what every thing means? i know what low pass is but everything else is confusing, and there is no gain on this amp, at least it isn't called "gain" AMP click that and go to the pictures.

hey maybe you guys can answer this. i have a SS labs 2 farad cap. i have lost the dang resistor to sucessfully charge this thing without it blowing up in my face. any clues? i know i can get resistors at radio hack but i don't know what the value was i dont have any paper on it and its 3 years old so i cant even find it online anymore.

I have a hifonics bxi2010 and wanted to know if its safe to run this amp a .5 ohm. I have a 200 amp alt, 2 runs of 1/0 wire, and 2 c&d batts in the back. Thanks in advance.

I'm looking for a deck that has the same style built in crossover as my CDA-9886 for my girlfriend's car. She likes the built in crossover feature of my deck, but wants something different. Any recommendations?

I have a Arc Audio SE-2150se, and I have it in mono mode, running at 2 ohms to my fully loaded, D1 18'' fi btl. Everything works fine, but I wanted to turn it up this past weekend to show of to my friends, so when I turn up the amp, from 1/4, to 3/4, it sounded much louder. But when I turn it up, the protect mode light will flicker red, just for when the bass drop, now I know this can't be good. It goes back green, but when ever the bass drops, a big one, it will just flicker red for that one second. Can any body tell me why this is, and is it safe to play it that loud? Not daily, I'm not stupid, but whenever I want to show off for a song or two, can I or should I play it…

Does anyone have an info for me on a replacement gain knob for the audiopipe 1500 amp's? Up till today this amp has been great but it seems the wires inside have came loose and im not the type to bust it open and put it back together.. This isnt my amp its in a good friends car. I have sent emails to the company with no response. Any suggestions? the knob plugs in with a "headphone" looking jack, not the phone cable looking one.