Home Audio

im gonna start a home audio setup for my room and im gonna make my own boxes for it. so far im looking into the emminence alpha 6.5 midranges on p/e. idk where to go from there as to idk which crossover to pick for which tweets. these are gonna be ran off my JVC 5.1 reciever. im gonna be running a separate deal for my sub setup. im looking for a good 12 or 15. im pondering the idea of using my 18 inch ssd. so far im looking at using the dayton 500 rms plate amp off p/e as well. im gonna be using this as a movie and music setup, but mostly music. any recs on box as far as ported or sealed are appreciated. im mostly looking for advice on the crossovers for the speakers.

Anyone here run an active home theater setup? I'm looking at possibly running 4 100 watt bridgeable stereo amps (for mids and highs) and 1 200 watt bridgeable stereo amp (subwoofer) along side an active crossover (behringer or peavey 3way stereo-4 way mono design or something else..?) The end result will probably be a stack of amps hanging in the basement and an infinite baffle subwoofer using the floor as the baffle (I may go ceiling, not sure what will sound better)... I'm not real sure on speakers, I'll be building everything. I'm thinking of making a large "sound bar" center channel with 8 3" woofers and 2 1 1/8" tweeters... I've got some towers from my last passiv…

What amp could power tower fronts center and rear channels? Fronts: http://www.partsexpress.com/projectshowcas...project=Jubilee Center: http://www.partsexpress.com/projectshowcas...m?project=UniCC not sure on rears but guessing no more then 40 rms needed? This is my first 5.1 build. I built 2 bookshelf desktop speakers and they came out great. Just not sure about amplification.

What's the website name to get used higher end audio gear from? Thanks m

Been building ths for a couple of weeks now.

what do y'all think about this reciever? yay or nay for a first step in my h/t world? wheeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee

Ok so I'm looking for a receiver to power the ZDT 3.5s. it has to be 4ohm stable and I'd like a remote and prefer 80W/channel at least.

how do I convert component audio to HDMI so I can use the TV for audio if my components are 20ft away and running one HDMI cable to the TV?

Hi all, I apologize for not being active in forever. I had to quit college to take care of my father with his aneurysm recovery, and now have a full time job with him, and another to get some cash. Life is busy. He is doing exceedingly well considering how bad his rupture was. ANYWAYS, I'm looking at picking up a decent turntable for my home theater. My Mom just told me she has numerous record from the 60's and 70's which I would like to listen to. I have NO knowledge of record players at all, so I'm hoping one of you with more experience could help me. I'm just looking at something to play the old vinyls. Budget under $200 preferable, and I have no problem buying…

Hey guys, hope you can help with some info, I'm building a sub for my home theater, using the RL-p15 and a QSC RMX1450, the amp is rated at 1400 watts at 2 ohms bridged. What would be my best option for hook-up to the amp, Dual 2 or 4ohm? Dual 2 ohm- one coil each side, or dual 4ohm to 2ohm bridged? Also this will be a ported enclosure, I can't do the 10 cu ft as stated as optimal, whats a good compromise betwen optimal and minimum sq ft for this set-up? thanks in advance!

not sure this topic belongs here like the title states looking buy a stereo that plays cd mp3s,am fm radio and my ipod.if you guys have ran into some thing simlar feed back would be great

I'm looking to build clean boxes of mids/highs and a woofer in a waist high tower. I was going to throw matching pairs of infinity 6.5s, 5.25s, and 10" unknowns in 2 towers and an RE XXX v3 in a woofer tower. Before I start building, what do I need as far as crossovers go to connect my mids highs to a 4/8 ohm load. looking to run a 400 watt receiver and a separate amp for the woofer. ANy good equip I can look for? Any recommendations for build or getting started? type of wood that looks really clean?

Well, First, I was either looking at two of these MLI-65 http://www.mach5audio.com/product_info.php...37171c76d02db5d OR MTX T4508-04 http://www.onlinecarstereo.com/CarAudio/Pr...ProductID=13307 OR Kicker 07C8-4 http://www.onlinecarstereo.com/CarAudio/Pr...ProductID=17406 But here is the thing, I'm not sure how I would power these. Also, how would I give it an audio signal. Then, as for speakers, and power for them and a signal to them, I'm at a complete loss. I would like to keep this as cheap as possible. Help, lol

after reading this section i have found out people here pride themselves on diy setups for home use..but i feel i have spent too much time and money on my trucks and not enough on home audio..i currently have a 72'' wide screen and im looking to bring it more alive so to speak..and i was looking into Onkyo HT-SP904 5.1 system with a budget of $700-$800 what do you guys think? http://www.circuitcity.com/ssm/Onkyo-HT-SP...ail.do#proddesc

http://www.partsexpress.com/pe/showdetl.cf...tnumber=264-821 I was wondering if it would be possible to use the new TB coax and then a large midbass in a tower and power them seperately using the cheap behringer active x-over? I was thinking the Tb coax + dayton rs270 for a 2.1 set up. If this sounds alrite, what all would i need to get this up and running? Two amplifiers, behringer x-over, reciever, pre amp, etc..?

BUDGET-1000$ WANT 7.1 NEED EVERYTHING BESIDES WIRING SO BASIC SPEAKERS SUB AND RECEIVER i was considering getting the yamaha ns-777 would like to use them as the fronts and also was considering a jvc receiver rxd301s http://av.jvc.com/product.jsp?modelI...athId=5&page=1 yamaha ns777 http://www.yamaha.com/yec/products/p...9&CTID=5002900 and this http://cgi.ebay.com/YAMAHA-HOME-THEA...QQcmdZViewItem for every thing else plus a sub which im having trouble deciding also this is for a collage house so it will also be used for a lot of party's so need to be pretty loud and clean... that why i went with a nice sets of fronts... but still want 7.1 souround sound any input…

So I have the following equipment I'm working with and want to build a new HT sub. Right now I have a Mach 5 MJ18 on a Parts Express 500 watt plate amp. I think it's around 6 cubes tuned to mid to upper 20's, not sure anymore. The box design isn't working with my new arrangement so I want to build something new. Basically I'm looking for opinions on if I should use the MJ18 again or use the pair of Sundown sd1 12's that I have. What would you do in my situation? I need somewhat of a multi purpose setup. It would be used for music, movies and video games but mostly leaning towards music.

I built this amp from scratch about 5 years ago. I also designed everything but the output stage... I weighs almost 100 lbs. It is a pretty sweet amp, it still runs like a champ day in and day out.... Class AB, 100wpc into 8 ohms, 200wpc into 4 ohms and 400wpc into 2 ohms..... So, I went ahead and cleaned up some of the crap I did about about a year ago converting my amp for 230V and adding grounding options... I added a 5 position barrier strip with selectable jumpers on the input side for setting up the primaries of the power transformers for either 115V or 230V.... I also extended the primary wires about 10" to reach the barrier strip. Next I added small toggles to…

so im beginning to start the process of adding a sub to my ht setup. so far i have a Arcam alpha 5 plus CD player, amp, and tuner..first problem i have is hooking the tv up to the reciever. ive tried going from TV out to Video on the reciever. ive tried from the VCR ( cable runs through the VCR) and tried through the DVD player...idk why but everytime i connect to the reciever the speakers start making a quiet buzzing sound. not noticeable during music but when between tracks its clearly heard and its annoying. how do i make it stop? and where would i connect an amp for a sub?

Edit

does anybody have any websites where i can find build projects that DEFINITELY have mtm or tmm build designs using 8" mids?? the closest thing i found were nataliep speakers. would i even hear a noticable difference bewtween 7 inch and 8 inch mids??

My dad is replacing his 15 year old receiver, but we have no idea at what brands to look at, or really all the features we need. We need about 100 watts for the front 2 channels at 8ohms and 75 watts for the rear channels at 8 ohms. His set up is old, so no center channel yet or dedicated sub, but we have two large towers each with a tweet, a mid, and a woofer with internal crossovers. We will be upgrading to a true 5.1 system, but as of now we are keeping the old speakers, probably for another year. Inputs will be from our PS3 and out digital cable box. Im not sure if you need anymore info, if so please let me know. Budget is around 250-300

would i be completely wrong for designing and making my own 2.0 speaker play back system for my mains? i have nothing on which to play back so they would essentially be my near fields. for recording and such.( actually my left over car audio speakers in my closet lol) i have 2 mmats mid ranges along with tweeters and passive x/o

i have a OZ ME10.2 i'm going to use for my HT sub. i'm wanting to incorporiate (sp?) it into a end table since i don't have one for eather coutch. if i do sub and port both pointing down, how far off the ground should i have it? i will be also going at about 1.25 cubes, what should i tune it to?

i keep seeing these in the ad bar on this site and the price looks really good http://fluance.com/fluan5speaks.html?gclid...CFQMngAodZzDx0A either thah or these: http://fluance.com/fluanhigthre.html my living room would look nice with either one. i like having a set of full range towers instead of separate pieces