Fi Technical

I have an older RE HC 15 with the 4 spoke basket dual 2 ohm version and need a re cone kit for it, it final blew about 2 weeks ago. I have been trying to to contact Fi via email with no response. Was wondering if anyone knew which recone kit on their web site is the correct one and will fit on the HC motor and wanted to get it upgrade if possible and add a need basket as well? Can anyone help me ?

how much would be to get a recone for a re xxx18 d2

I just did a re-cone for 2 BL 12's and it seems that the 2 re-cone 12's play harder and have alot more excursion now than the other 2 12's in my enclosure. Is this because they were re-coned or is there another problem? I had all the coils metered yesterday and the 2 re-coned subs coils read lower than the other 2. Would the lowere impedence make them play harder?

I was considering a trade for 2 BTL 15s ( Single slug, spaceship motor), but the subs only have the cooling option. I am going from 4 SA-12s, and I like my lows. I'm powering them with 2 Audiopipe AP3ks. I was gonna run them in 3.5 per (7net), and tune between 30-33hz. I listen to alot of rap, low bass music, and I really want to be able to play in the high 20s/low 30s with authority. With just cooling, will these 15s be able to produce like I want them to? I'm only getting rid of the SAs to do a forward firing/sealed off setup, and I can't get 4 12s to fit in a blowthrough. I also wanted to see what FI was all about Thanks for any help

Hey guys, I have an 18" BL running at about 1200 watts and this thing moves air. I've had some problems with my rear deck flapping up and down no matter how much I seal it off. It seems air is always getting into it. It will even start shaking my rear seats and moving them in and out (they are foldable). My rear speakers currently are a sealed speaker. In such that they are an older JBL pair I got from a friend's lincoln. So the cone isn't being moved or anything by the air. I don't ever use rear fil, i just threw them in there to help seal up the rear deck and so on. My question is this though...by attempting to seal up the rear deck (dynamating it, covering all the hole…

To get right to the point I'm trying to determine what upgrades are necessary, and most importantly where to get this done. I installed a 200amp alternator, and 3 batteries with a single run of 1/0 from the front. I am wanting to run around 8-10kwatts rms, have about 7k now, and want to try to keep my voltage pretty steady. More batteries are in the plan when I figure out how to put them, but I really want some info on the alternators/wire. I have this on 2 btl 18s. I went to all the local shops here in Myrtle Beach, including alternator specialist shops, and besides the one that wanted way too much for a 300a alt, all of them said they could not get anything above 200amp…

Hello guys I am looking for stories or possibly someone with some experienced advice that may have used q 18's in a 2003 explorer . first of all I have a 2003 explorer with a 4.6 v8 ,220 amp alternator 2 runs of 1/0 kicker power wire, 4 stinger spv44 batteries. cda9887 alpine receiver ('audio control matrix' voltage booster in the near future) to a jl slash 300/4 powering focal 165v2s's front and rear , a audioque 2200d to power 2 fi q 18's w/bp power dual 1's , a audioque 1200d powering a digital designs 9515, as well as a digital designs 1510t will be ran in the center console , I don't have the amplifier for that yet and yes there will much more than likely be m…

Sup guys. I currently have 2 15s in my car and the box is around 4.7 cubes. If i got 2 15inch btl fully loaded subs would i have to increase the cubes of the box? Thats my max cubes that can fit in the car

getting two 12inch BTL's fully loaded, dual 2 whats the optimal cubic feet this box should consist of and optimal port size

well as u can see i have a kicker zx1000.1 rated at 1258 watts. which i do not have installed in my car yet which is an 02' dodge stratus R/T coupe, and i think it hase either a 85amp alt or a 90 amp alt. And im also goin to be buying a 15" BL w/ the p chamfer i already have the big3 upgrade done with elemental designs 1/0 gauge wire will i have to consider on upgrading the alternator?? ive looked all over the net, and i just cannot find one for my car, so i need some help on that IF i do NEED to upgrade and wat about mabe a battey or 2?? thanks

Is there any recommended size fastners to use on the N3? From what i saw the holes were only about 1/8".

Like title says........what is the recomended port area for an X 10? It will be in .75cuft using aero port...............I'm thinking I read a 2.5" was enough once just need confirmation.

Hello all. I have just found out about Fi yesterday. Seems like a solid product. Everywhere I read everyone has positive things to say about them. I am in the market for new audio toys in my truck. Stumbled on this website and thought id ask some of you gurus about some suggestions. Some info for you. I have a 05' Single Cab Dodge Ram 1500. I have taken down some measurements of what the enclosure "could" be up to. I would like if possible a slight wedge box so I can still lean my passenger seat back a little. This is what I came up with. Length of box from side to side = 38" Height of box = 18" Bottom width = 11" Top width = 8" Ive done this calulation on Fosgates box …

Are you guys able to recone a 10" TC OEM woofer. The surround had ripped completely from the center cone and i just want to have it fixed.

Hey i was wondering if you guys could recone a Rockford Fosgate HE? I cant find any recone kits.

i need a btl fully loaded d2 18 recone (w/ old style motor) if anyone can help plz let me know

How much is one of those shipped to 68510? Also before you build it is it possible to have you guys put the biggest lead wires on there (like the ones you shipped me), because When I took mine apart to fix the wires it worked fine but the copper wire broke right next to the coil, and now I have no copper wire to solder the lead wires to. let me know if there is a way to fix this problem. Also would it be possible to send you the sub I have and get 2 10" Q's and a little bit more money in exchange? I think that I am going to go for sound quality this year, since I have a bigger car now. thanks Chris [email protected]

do anyone know what the prices will be to recone an ssd 12 2dvc Flatwind Coil?

Need to recone my 12Q i bounced a screw threw it drilling it down. rip in the rubber

I have an 18 SX that I would like to have reconed. What is the procedure to have the sub sent in and reconed? What would the estimated price and shipping to 30286 (Georgia) cost? I emailed Fi Car Audio about a month ago, but unfortunately, I never got a reply. I've sent a couple more emails here and there, but still, no luck. Anyone have any ideas of how I can get in touch with them? I would call, but I was unable to find a phone number. Many thanks, Mike

Ok I have a x 10" with single magnet structure. Svc 4 ohm. I need this sub to be a svc 2 ohm and have a small tear in surround fixed. I have emailed fi twice on this and gotten no response. Anyone know how much it would cost or anything about reconing this?

Finished the recone on a fully loaded BTL 15 today and this thing sounds even better than what I wouldve ever guess... I have one question though... I brought the sub to a friend who owns a shop to get the recone and after playin it a bit... Pulled up to a friends house and noticed the dust cap fell off, so I bought some more epoxy 5 min loctite and put it back on no problems. After expecting my little glue job the dust is maybe 1/16 of a inch off from where it used to be. Will this hinder the subs performance at all? Its sounds fine to me, still loud as chit...(My wife said it sounds like a machine guns going off in the trunk.LOL) this is only a temp system... Next syste…

I'm finally good with money, and I'm looking to turn my brahma MKII motor into the first 18" brahma MKII I know of... and of course I've known you guys were the best people to ask, specifically scott has been referred to me by marshall, black00... email me back or here, [email protected] thanks a ton for taking your time, steve

I Emailed Fi about a month ago about the reconed and i haven't heard anything about it. If u could let me no what is up

I have a 15" Soundsplinter RL-p thats in need of a recone. Sub works fine, just the cone is starting to seperate from the surround. Tryed CA glue and it worked well for a while, but its coming lose again. I was wondering if a recone was possible for this sub. BTW, I sent a email to Nick a few weeks ago, but didnt get a response, so I decided to make this thread to possible get a solution. Thanks.