well i found a new toy that loves the high notes.in our testing it was able to do a 155 outlaw @ 71hrtz with 1 NS12 and a 40.1 on 12 volt.this new vehicle is stock from head to toe. no damp,no duct tape nothing yet.since i was using a freind of mine equipment.I need to start getting my own again so I want to go with a lighter sub like 2 x sa10's and a [email protected] to start out with since i cant afford what I need.

will the sa 10's hold up to some 71 hrt burps until i can afford some bigger subs and more power?

this new vehicle is crazy loud to start out we tested for about 2 hours before we got to a 154.7 with a box that was just sitting in the garage. LOL once i find the sweet box,damp and some trick's I think I can get this close to a 160 outlaw.

I've built and modded 6 box's so far even did a bandpass but the sub didnt like the 4rth order and the spiders all came loose.

cant wait to get started BUT money is real tight right now for me and mine!

The Z peaks higher than NS and SA, check those out. Look out for issues with the SA series pounding above 1000wrms.

Sure they can but you will be buying re-cones

Don't forget it doesn't have a massive 4" coil.

Enjoy music for once not burps

If you wanna keep it loud, don't put deadener at all.

I don't get it. Isn't music louder to the ear once deadener is applied?

The Z peaks higher than NS and SA, check those out. Look out for issues with the SA series pounding above 1000wrms.

cash flow!

Sure they can but you will be buying re-cones

this is not a daily driver setup it will be built and used with budget in mind. so finding the what these subs like and what will help them last a couple of shows will be key

Enjoy music for once not burps

because its easier and cheaper to burp a high score then it is to build something to play 35hrtz everyday at the same high score

If you wanna keep it loud, don't put deadener at all.

well thats what they said about the crx's when they first got used but now everyone and there mother with a crx dampen's them.also the next best thing is there is only a couple of interior panels.so it will be easy to dampen it and test and remove with in minutes

If you wanna keep it loud, don't put deadener at all.

well thats what they said about the crx's when they first got used but now everyone and there mother with a crx dampen's them.also the next best thing is there is only a couple of interior panels.so it will be easy to dampen it and test and remove with in minutes

Um, no one deadens them. Where did you get this information from?

If you wanna keep it loud, don't put deadener at all.

well thats what they said about the crx's when they first got used but now everyone and there mother with a crx dampen's them.also the next best thing is there is only a couple of interior panels.so it will be easy to dampen it and test and remove with in minutes

Um, no one deadens them. Where did you get this information from?

not sure where you have been but you go on termpro and usaci forum and they will tell you that they deaden!

terry brock has his dbl layer

the guy from cali that beat brocks street a score a couple years ago

a person that took second the same year brocks score got beat

american bass team there is a ton of crx's that are matted

dc anna's crx is matted

the list goes on

but like i said it's very easy to test in this vehicle.there is no removing panels and putting them back at all

the top 5 in this list had crx's and they all had deaener

dB Drag Racing - Street A

Place Country Competitor SPL FoMax

1st Team XS SPL - Tuan

156.1

2nd Team SPL Bank - Scott

155.6

3rd Ryan Ferguson

155.4

4th Team Neo - Eric

155.3

5th Terry Brocks

155.3

6th Advanced Mobile Toys

154.6

7th Team Gameover

154.3

8th

Edited March 18, 201114 yr by stevew007

The SA can take some good burp power... we have done 2.2k on an SA-8 stock copper coil @ 68 hz -- and they use a smaller 2" coil vs 2.5" on the bigger SA

The SA can take some good burp power... we have done 2.2k on an SA-8 stock copper coil @ 68 hz -- and they use a smaller 2" coil vs 2.5" on the bigger SA

The SA-8's are little beasts, but that is just INSANE!!

The SA can take some good burp power... we have done 2.2k on an SA-8 stock copper coil @ 68 hz -- and they use a smaller 2" coil vs 2.5" on the bigger SA

The SA-8's are little beasts, but that is just INSANE!!

No joke!!

If you wanna keep it loud, don't put deadener at all.

well thats what they said about the crx's when they first got used but now everyone and there mother with a crx dampen's them.also the next best thing is there is only a couple of interior panels.so it will be easy to dampen it and test and remove with in minutes

Um, no one deadens them. Where did you get this information from?

Mine's deadened, and the loudest CRX's are deadened as mentioned. If I can do 152's with a single SA8, I'm gonna say deadening probably helped.

The SA can take some good burp power... we have done 2.2k on an SA-8 stock copper coil @ 68 hz -- and they use a smaller 2" coil vs 2.5" on the bigger SA

Yup, and not only did I do it once, I've done it hundreds of times without failure. I'd do a pair of SA's before a pair of Z's in that application.

The SA can take some good burp power... we have done 2.2k on an SA-8 stock copper coil @ 68 hz -- and they use a smaller 2" coil vs 2.5" on the bigger SA

The SA-8's are little beasts, but that is just INSANE!!

152.2 in the kick, 148.9 sealed on the dash worth of insane