SPL & SQ / Fabrication

Currently I have four Kicker Comp 15s doing a pretty good #, really pounding for a street beater on such a low budget. In the vehicle, we have room for a 4th Order Bandpass. I used a calculator from www.carstereo.com to design one but doubt its accuracy. Can anyone aid me in designing a 4th order bandpass, or link me to a site with theory/equations for one? Simple calculators are hard to trust w/o knowing the math behind them!!

Subs:2, Sundown Audio E-12 v1, 400rms Amp: Hifonics 1700.1 wired to 1 ohm (so 850rms per sub) Box. Custom mustang vert box, .9 cubes per sub sealed. Right now the E-12s are reversed mounted to get the most usable airspace. Is there a subwoofer that would better handle the power such as the soundqubed HDS 200 or 300. Also, should I stuff the box with polyfill or something? I can't turn my volume up to even half on some songs before the subs start to distort or bottom out. So what can I do to improve my setup?

Im about to start building my box today, and i want to know the right screws and glue to get for it. thanks for the help.

I am thinking about picking up a new ride to play with and probably compete in. i know CRXs are concidered "loud" but what about a camaro. Similar shape. much bigger ballz! anyway i was wondering if anyone has seen any loud camaros at the shows.

2012 focus sedan. currently running a prefab decent but cheap box ..in its current position metered 138 @ 37hz sealed on the windshield. fired the box forward today and noticed it wasn't half as loud this tells me my positioning is right for this car. So my question is do you think this box is working well or should i build a new box different specs i don't compete but i like loud and low this setup is pretty good for a single 10 but i think there is room for improvement would like some opinions/box ideas my max dimensions are going to be around W x H x D 30x14x27 to easily be able to fit through trunk opening which is a must as it needs to be removable when i DJ A…

Just starting an install journal here. Ive made most of the progress so far only having the trunk left to do after finishing up the install of the kicks/horns. Feel free to ask any questions. See sig. for other components in install. thats all fer now folks

i built a sealed box for this sub .6 cubic feet and it sounds good but it depends on the notes and it just drops off different notes and its loudness lacks majorly im very disappointed in this subwoofer... i have 800 rms going to this sub at 4 ohms and my amp can be wired to 1 ohm at 1600 watts rms and it still sounds like crap? help a brother out.... thanks im at lose and ready to sell the box is air tight its a good box. i m lost ?

I looked at a couple of websites but am still confused as to how to tune the port to the frequency you want. And how does the length, width, height of the port affect the tuning?

If someone was going to build a sealed enclosure, and the woofer in question listed a box size of, say 0.75^3 to 1.5^3, how do you determine what size ^3 would best suit the woofer? Is that something that the tsparameter would tell you? Or, just build something in that size range and get equal results??? Just curious...

Crazy, stupid, or cool? Thinking about doing wall with 2 18's. Not for spl, just daily pounding.

i finished putting this togethre right now... LMK what you think. I'm uneasy about the tuning freq because i was unfamiliar with the calc. i used. since the box is wider, i can now have a good 26" of port area. anything wrong with what you see? the sub itself is .3 cubic ft but i will add more baffle to compensate

I am looking for some songs with very good LOW bass notes. The best I have so far are: 24 23 by Trae (and by jeezy, there are two versions), Dopeman by OJ Da Juiceman and In Tha Hood by Trae. Preferably not chopped and screwed (or slowed), as I can do that myself if needed. Thanks, --Chris

So i was metered today and this is what i got... 144.6 Outlaw under the floor @ 39hz and an oddity i scored 145 @ 39hz legal on the windshield The shop i was at thought it was quite odd that i was hitting higher in legal than i was outlaw. 15 fi bl on a saz-3000d @ 2 ohm

Wassup fellas I am wondering if I tune my port to 33 hz could I change the tuning of it without switching out the port? Like adding something? I would like to keep it at 33 hz when doing rap demos and daily bumping but then when I use it for work I listen to rock cause of my boss cause he hates rap so tune around 38 hz or maybe a tad higher. I have an hdc3 18 and 8 cubes or so to build.

So I'm trying to make a center console and I'm going to put some 6.5 evils in both sides of it. Seeing is the mids are facing back to back should I put a divider between them? Is it going to call his cancellation if I don't? If I do or don't should I be putting polyfill inside this also?

Ok I've been doing a lot of research on standard 6th order bandpass boxes, and haven't found enough information to decide if its better than standard ported for spl. If I tune a 6th order with a very narrow high output passband, such as 39hz rear and 44hz front, or in this general region, will it be louder than a ported box with a similar tuning? From what I've seen the 6th order will boost output higher, but it strains the subwoofer more and lowers power handling, so it has more output but you can put less power to it so they balance out... I want to try one out but if you guys think it wont be louder than just ported for spl use only then it's not worth trying. Also I…

Thanks in advance for the help. Alright I am planning on getting a 12" Fi Q D2 and already ordered a sundown SAZ-1000D to power it. I've never built a box before and I dont trust the audio shop here. I want to build a L shaped ported box. Its going in a 1997 chevy blazer so I have room. First should I go sub up port back or sub back port back? What are the benefits of each keep in mind I'm not going for spl. According to Fi "Ported box we recommend using 1.8-2.5 cubic feet @ 28-33Hz (I personally think that a 32hz tuning is optimal, and has the most output and is still the most musical daily driving). Use 12-16 square inches of vent area per cubic foot of volume." So I…

I posted under another topic but calculated the wrong numbers so here is the updated version. The other post topic is misleading so that is why i posted a second time. This should answer any questions of why i posted another topic. I apologize Admin. This link shows the design outline: http://s883.photobuc...re.jpg#comments Here are the numbers: Wedge Enclosure Width: 43" Height: 27" Top Depth: 8" Bottom Depth: 20" Total Volume: 7.885 cb.ft. Port (32Hz) Internal: 20.0"H X 4.0"W X 24"L External: 20.75"H X 4.75"W X 24"L Port Displacement: 1.3689 cu.ft. Woofer Displacement: 0.38 cu.ft. (2 Fi Q 15s) Bracing Displacement: 0.1255 cu.ft. Net Volume: 7.885 - 1.3689 - 0.38 - 0.12…

Want to build a series-tunes 6th order for a Single Fi Car Audio SSD 18. Not sure where to start I know 6th orders are more complex to design and more of a trial and error build but if I never try it out I will never learn. So of course the goal is to successfully build a 6th order but depending on the final results if it does not meet expectations there will be adjustments. Also if none of the revisions succeed I will fall back on a standard Ported Enclosure . Please if you have any useful information on 6th order designing/building It would be awesome if you can share them with me . Thanks in advance max dimension - height 30” - depth 21” - width 38…

So the plan was to build a trunk box that was larger with more port area than the box I had previously but I ran into a bit of an issue much too late in process.... After we finished the box, I tried to slide it into the trunk. Didn't fit Damn you Corolla and you're itty bitty trunk opening. Inside of the trunk would have fit it fine but it could not be fit through the opening. Sooo, I have another backseat box. LOL It sounds insanely better which is a plus, but I guess i still fail a bit in the end. It'll do for now... 4 cubes @ 31hz, 18 sq inches of port per foot. Tell me what you think. (Besides telling me it needs to go in the trunk )

Current setup for my 15" Xcon: Sealed enclosure with dimensions - H: 17" W: 32" D: 15" Total space I have is: So I want to do sub up, port side firing w/ aero ... Does this looks good in Torres' calculator???:

Help me out. I can't afford a ton of batteries so I can only go into a class with minimal bat requirement. :boxin:

1st run 150.7db 2nd run 150.1db charge batterys a few min. 3rd rub 151db got 1st place

I am currently building a new setup and I am torn on how to tune my box. I will be running 2 18" Fi BTL N2's, 2 Hifonics 2600.10's, and 4 XS D2400's. I am posting to get feedback on which setup would be best, going with a spl setup and tune my box around 32-35 Hz, or go with a wave setup and tune my box around 25-28 Hz.? Feedback and oppinions are needed thanks.

i just went to my first sq event this weekend and the advice i was given by the judge is to try and widen the soundstage a bit along with getting the image a little higher. i sorta noticed this before but not really so brushed it off but after listening again post judging i could definitely see where he's coming from. he said its slightly above the a pillars and slightly wider then the car but needs just a little more. I listened to hotel cali again along with some michael jackson on the way home and noticed this 100%. any advice on how i would do that? Pointing my drivers side tweeter up helped a lil bit on some songs but I'm pretty sure I'm lacking some midrange up high…