Sundown Audio

Ok I am buying a little Mazda MX-3 Hatchback to have some fun with SPL local shows. I want to buy this guys NS 18 and I need enough power. Mostly for daily with some burps a weekend a month.

ok, so i've got a saz1500d, i'm going to get a chevy impala 00-04, i gave the gf the type r 12"s i originally had in my lincoln towncar, i'm thinking single 15" for the next set-up so i can give it the box space it needs. would a single nightshade 15" w/1500 rms in an optimal vented and tuned enclosure put me in the mid to high 140's?

We are opening a sale on our "E" and "NeoPro" lines for the month of February starting today -- the prices are as follows : MODEL // REGULAR MAP // SALE PRICE E-8 v.3 -- $95 -- $80 E-10 -- $105 -- $85 E-12 -- $110 -- $90 E-15 -- $130 -- $105 NeoPro-6.5 -- $99 -- $69.99 NeoPro-8 -- $105 -- $74.99 NeoPro-10 -- $129 -- $89.99 Price is for EACH speaker on the E series and NeoPro series. E series are all available in D2 and D4 coils. NeoPro series are all available in single 4 ohm and single 8 ohm coils. Find a local or online dealer to order : Find a Dealer Dealers can call or e-mail us with any questions on the sale -- may take a few days for the word to get around to all of…

Okay if I've done my math correct, the 3500D (with a 350A fuse), I should be able to power this thing with a 250 amp alternator and (2) D3100's (117 AH each) running at 1 ohm on (2) of the of the Z15's?

Jacob did you get the shipment of 3500d's on Friday as expected? Will I get an email when mine is shipped so I know when to be expecting it to arrive? Thanks!!

Jacob, How would I setup a 1200D and a 125.2, Rca wise? I know how to, but I am just double checking. I would run Rca's from the sub output to the 1200D and Front to the 125. Correct? If I wanted to hook up another 1200D, I would just use the pass thru right? When I get the 100.4 I run Rca's from front and rear right? Just Wonderin so I can have everything when My HU comes in. I'm going out on Halloween and I wanna flex a bit

After reading the FAQ, it seems that the speaker wire outputs are parallel wired inside the amp. I'm trying to wire a SAZ-3000D for a single one Ohm load. Do I need to sum the positives and negatives outside the amp or can I just pick one set of + and - and get the full wattage out of the amp. Thanks. Carl

Stripping the Explorer down... Alts and voltage regulator are pending... if they don't sell will list them later. In any event... batteries and wire : 7x D1000s -- 200 shipped each 1x D1000 -- 160 shipped (needs re-threaded) 4x D1600s (the other six are mine) -- 225 shipped each All rest at 16.7v or higher * Standard red stinger expert wire * 2.50 per foot + SH * Standard black stinger expert wire * 2.50 per foot + SH * Mixed Knu and Stinger Flex Wire * 2.75 per foot + SH FOR ALL WIRE $1200 + SH Approx 564.5 feet total (550-575 actual due to rounding each piece off to the nearest 0.5) with TONS of ring terminals on it. I will prefer to sell it all at once... but if …

I've got a couple of questions for ya. I recently purchased an saz1500 with the intent of running only one SA8 (d2). Which I have already purchased too. The goal is a tight musical system for daily driver. The concept for the box - install is to build box tall and set in the corner of the hatch back leaving room for groceries. I have approximately 2 cu ft to work with. I would like to have the ported box portion on top of a battery compartment using the same enclosure. Here are some questions 1. Will I have battery problems because of the vibes from the box? 2. Will 1500 be too much for one 8? 3. Is a second battery needed? Vehicle 2009 Honda Fit Stock HU Stoc…

I can either get a second SAZ-2000 or a single SAZ-3500. I am leaning more towards getting the second SAZ-2000 so I can have more power. But I like the thought of having a single powerful amp. But on another note, I am VERY impressed with the 2000, it does more then rated power all day without getting more then luke warm. my SAX-100.4 gets warmer then the 2000 does. These will be powering two RE MT 18"s

too start off I'm not bashing any products this was just a direct swap. we started out with this box on a 40.1 @.5 did a 154.9 then we dropped this in and only came up with this voltage drop was from 15.2 on the volt meter down to 13.4 on the 40.1 and from 15.2 down to 12.3 on the 4500 there was a nsb90 under the hood with 6 runs of wire to the back batteries they are 110lb data safes. the 40.1 was giving some crappy wave's on the TL and the sundown hard perfect wave's on every test we are going to do the 4500 on 16 volts next and see what it will do then here is a pic of the wave with the 40.1

making the debut show this weekend at elite audio meca sc state sound fest. 1 ns 12 and saz-2000 in a mazda ext cab.

I know this is backwards of what most people ask, but I cannot find it documented anywhere. I have limited space, and I'm trying to upgrade my system using the equipment I have sitting in my garage. So, that would have me using 2 channels of my 100.4C bridged - running a single SD-1 10" sub...which is an 8 ohm sub. So, what I'm wondering is how much wattage I will be able to get out this amp at 8 ohms bridged? My guess, based on the published specs, would be in the neighborhood of 200 watts. Just looking for a confirmation of this. Thanks!

I think this will be my last try to get some information. So you folks are my last hope to help or point me in a different direction. Here is my question. If I want to build a box of X cubic feet and there is not enough space where I want to build, can I build another box and have the two boxes attached by pipe or tube or sealed passage way etc.. Example: I would like to build a box in the right rear most corner of my trunk but there is only 1.5 cubic feet of space available if I build the box, and my sub needs 3 cubic feet. But if I built a mirror replica of the enclosure and installed it on the left rear most corner of my trunk and connected them by... I don't know, let…

would this amp suit these subs? or would it need less juice for these subs? i hear the E8s can take 800 but RMS is 200...JWing...looking for a good resonably priced setup... thnx Doyle

I have a sax 100.4 and the crossovers on this amp are awesome! My question...Whould an Alpine Imprint Sys improve the sound, or just use the crossovers on the amp.

well as it states whos comin I probably cant make it I could probably get sunday off if I asked I might have to gotta check out the show and support the team. oh well if I cant make it Im always a phone call away as a few will tell you

Can the centre logo trim piece be rotated 180*? Pics to show what I'm talking about. Please excuse my horrible photo-chop

whats the cost of reconing a 15" ns to a 12" ns?

How do i get some of these? i broke one pretty easily today and would like to get a few spares to keep on hand. do i get them from jacob or dose home depot sell something close. if so what size, what pitch? thanks

yah im the champ

Ok, the last couple of shows I've been to I have been down a few tenths. 157 at the Vinny, 156.9 this weekends Madvette show. I know my voltage has been an issue, but I'm working on that. So I discovered (by accident) another way to wire my subs to a lower load, and my amps don't go into protect.

I see that the 1500D have 2 sets of speaker outputs. So the easiest way is to get dual 2 ohm, hook it up in parallel, then the internal are bridge for a final 1 ohm load. What if I were to go with dual 1 ohm (1 sub) wire it in series = 2 ohm, then bridge the connection to the amp, will i get a final load of 1 ohm? I can't tell from the manual if the external outputs are bridgeable. Please confirm. Thanks!

I still have mine, and alls good at the moment. Thinking about getting another amp. Curious about them because I didn't see them on your new site. (since the last time I've seen it)