Sundown Audio

My SAX-125.2 has completely stopped working. I took a look at it today and it just stalls into protect. Inspected the inside and nothing is blown, however I found 1 fuse blown and replaced it with the same amp rating (20amp) and it is still in the protection loop. The amp was fine until aprox a week ago it would randomly turn off for a second then pop on. There was also a very high pitched sound coming from presumably the amp. any ideas?

Here it is! Super small little amp Without mounting feet included the new amps are sized as follows : SAZ-1500D: 8.30” x 2.32” x 16.53” SAX-125.4: 8.30” x 2.32” x 11.02” Factory tested power as follows @ 1 % : 138x4 at 4 203x4 at 2 438x2 at 4 I'll be pretty busy for at least a few days but I will get my testing as soon as possible. On to the photos with the 1500D v.3 and the 100.4D revision : * Hard to tell but there are small holes in the board on the right for the fan on the opposite side of the board to breathe. * 1500D v.3 and the 125.4 together * WOW * 99% of the crossovers... only lacking the 12/24dB slop switch. Fixed at 24 dB now.

WoofersEtc.com - SAX-200.4D - Sundown Audio 800W 4-Channel Amplifier MAP was $815 on these - they are being sold at over 25% off that price now from WoofersEtc.com exclusively. Get em while they last

Yep... you read that correctly. Big bad boy 200x4 Class A/B amps with full SAX-100.4D style crossovers. Stable to 1 ohm mono / 2 ohms bridged... can power a whole system. These things are MASSIVE... I know the trend is for small amps but I like big amps, and so do alot of people still These are not made for typical daily installs... they are made for BIG builds! * It is actually larger than an SAZ-3500D. * Another shot vs. SAZ-3500D ----- Before anyone asks... there is no ETA, I don't know when I'm going to open a pre-order, and pricing is not 100% set. I do expect pricing to be about like the SAZ-2000D, though... give or take.

Sundown SAX-200.4 - DIYMA.com -----

As much as I love the beast that is the 200.4 it's our lowest selling model. We are teaming up with WoofersEtc.com to get this closed out -- keep your eye on their site for them to be added at a special price. I am saving one for my personal car as it's an awesome amp -- so if you wanted one get in touch with WoofersEtc.com soon

Had another one made... the last proto was destroyed in shipping so didn't show up with the rest of the bunch! * Slightly larger than the SAZ-1500D 250 x 2 @ 4 ohms 500 x 2 @ 2 ohms * 1000 x 1 @ 4 ohms * * Rough numbers, pending testing.

Please say the upcoming (and highly anticipated for me anyway) SAX-50.4 model will have the same awesome crossover capabilities as the new SAX-100.4 Rev D?

I am discontinuing the SAX-50.4 and the Sundown Z15 Woofer. Paypal me at [email protected] to order. The SAX-50.4 close-out is also available at any authorized dealer -- the Z15 close-out is only available from me directly. ---------- SAX-50.4 -- $200 shipped in continental 48 states I will still include a 2-year warranty on these. Most customers shopping for an amp at this power level are more concerned about $ to watt and less about crossover flexibility. So we are closing out the 50.4 and will be developing a less expensive model to replace it without as much crossover flexibility to offer more watts per dollar. ---------- Sundown Z15 D2 or D4 -- $250 shipped…

Creating a new and separate thread to clear the clutter. We still have a fair amount available ! ---------- Paypal me at [email protected] to order or talk to your favorite dealer. ---------- SAX-50.4 -- $200 shipped in continental 48 states I will still include a 2-year warranty on these. Most customers shopping for an amp at this power level are more concerned about $ to watt and less about crossover flexibility. So we are closing out the 50.4 and will be developing a less expensive model to replace it without as much crossover flexibility to offer more watts per dollar. Make no mistake... the 50.4 is deceptively powerful as it produces over 60 watts per channel…

$200 shipped in the continental USA on pre-order! Payment via Paypal to [email protected] Same crossovers as SAX-100.4C Revision: # Selectable HP / LP / FULL crossover # CH 1 & 2 Variable HP crossover 50 - 5000 Hz @ 12 dB # CH 1 & 2 Variable LP crossover 50 - 500 Hz @ 12 dB # CH 3 & 4 Variable HP crossover 50 - 500 Hz @ 12 dB # CH 3 & 4 Variable LP crossover 50 - 5000 Hz @ 12 dB # 10 Hz - 500 Hz variable subsonic filter (CH 1&2 and CH 3&4) # Subsonic filter allows for band-passed crossover configuration # 50W x 4CH @ 4 ohms # 80W x 4CH @ 2 ohms # 160W x 2CH @ 4 ohms 12" x 9" foot-print - just slightly longer than SAE-1000D!!! ----- Photos o…

Regular MSRP $349. Special price $225 until end of March! You can order from your favorite dealer OR Paypal me directly at [email protected] Rated power output ----RMS power, 4 ohm stereo 50W x 4CH ----RMS power, 2 ohm stereo 80W x 4CH ----RMS power, 4 ohm bridged 160W x 2CH Signal to Noise Ratio >90dB Low pass frequency crossover 50Hz~500Hz (CH1&2) 50Hz~5KHz (CH3&4) High Pass Crossover 50Hz~5KHz (CH1&2) 50Hz~500Hz (CH3&4) Variable Subsonic Filter 10Hz to 500Hz Bass Boost 0~18dB Variable Bass-Boost Frequency Control 35Hz to 120Hz Frequency Response 10Hz ~ 40KHz (+/-1dB) THD@RMS Watts <0.1% Channel Separation 75dB Fuse Rating…

I missed out on ordering one of these when they were still in production. I would really like to find one for the new truck. Anyone know where I could find one in really good condition? NOS anywhere?

hi, i am going to be getting Polk Audio MM6501 speakers in a week. and i am wondering what roughly would an sax100.2 do at 3 ohms? i want to assume around 150rms since the rms doubles going from 4 ohms to 2 ohms. but wanted to ask just to be sure. thanks.

At what voltage is the sax100.4 rated at?

Just wondering what the output would be on the SAX100.4 in 3 channel configuration on a 2 ohm load. Looking at powering a set of 2 ohm 6.5" comps and a DVC 4 ohm 12" sub. Thanks

Hey guys I just got my amp today its HUGE. Im running 2 sets of comps off this amp, Hertz HSK165 for the front and infinity kappa perfect 6.1 for the rear. I thought i hooked everything up properly but that was not the case. My balance and fader controls are wrong, when i adjust to left or right the front left and rear right work. I dont know whther the speaker wires themselves are wrong, or if iinstalled the rca wrong. There are no markings on the rca just 2 red and 2 black so I dont know where they go. Secondly, I need help setting the adjustments. I want this amp to be stritcly for mids and highs since I have 2 subs. I set it to HPF for both switches on the amp…

What would cause and amp to automatically pop all 3 fuses when the ground and power and hooked on. Like as soon as the power is put on the fuses blow. I just took the amp out of my car. It was working wonderfully. Put it in a friends truck today and this is the problem we are having. Please advise. thanks

i have an sax 100.4 and i have 2 pair of alphasonik pct6551 3way components,2 for the front and 2 for the back there are rated at 350 watts rms would the amp be powerful enough to power the components. or should i sell them and get a lower rated component set?

I am using a SAX100.4 to power my ID OEM mids and Focal tweeters. Channels 1 and 2 go to the tweets and 3 and 4 go to the mids. They are being crossed over in my Alpine CDA-9887. SO my question is what signal will be present at the 100.4's RCA outputs? Does the amp sum all the signals together so I will have a full range output there or does it just use the inputs from channels 1 and 2 or something? I want to run some rear fill in my Acura MDX and I was thinkin about picking up a SAX100.2 but I dont know how to get a full range signal to it because my deck only has 3 preouts. Any ideas or suggestions are appreciated.

Wondering what the power outputs are for these? Looked in the store but didnt see them there

First off, I hooked up the power wire and ground wrong. Power wire in the ground slot, ground in power slot (yeah i fail hardcore). I had the speakers wires hooked up and the RCAs, and remote wire. Not sure if this caused the problem, but definitely a good possiblity i believe There's a hiss coming from my speakers when i have the volume all the way down, and i can faintly hear distortion when the speakers are playing. I regrounded the HU (a 9887), checked the ground on the amp, they're fine. I switched RCAs and the hiss/distortion was still there. I had some cheap RCAs that have a 1/8" jack on the other side, so i took those and hooked them up and hooked my Ipod dire…

How do i get some of these? i broke one pretty easily today and would like to get a few spares to keep on hand. do i get them from jacob or dose home depot sell something close. if so what size, what pitch? thanks

I have an SAX50.4 bridged to a dual 4ohm sub. Tuesday at the end of my 3 hour commute the amp shut off. I thought I fried the speaker but 10 min after the amp shut off, it worked again. I had already stopped when I turned the stereo on again and the amp was hot to the touch. This is the same thing that happened with another small amp that I had but it was 2 channel bridged. Except it shut off after about 30-45 min. I have an SAX125.2 running two 6x9s right next to the 50.4 and it hasnt ever shut off since Ive had it. Doesnt get hot either. They are both screwed to a seperate piece of 3/4 mdf behind the back seat agaisnt the side of the box. Ive also had 2 other amps in t…

here are the first works on the machine made by us with the subwoofer Nightshade 15! amplified by 2 steg 310.2 (3000watt a-b), await the arrival of saz-3500D 2 batteries 12v Classic sounds very strong and very good, very beautiful and aesthetically 147db measure of media in 30 seconds, given to 40Hz