Build Logs

well unfortunately i dont have complete"biuld" pics but i do have some i can share.heres what i have to work with.first thing first,the vehicle.

m/albums/uu129/aqfirebird/cliffsfirbird018.jpg 1996 firebird 4 AQ HDC 12's with 4 AQ 2200ds the car is as on audioque.com and is the 2009 incriminator point cup champ!

My wifes truck is a 98 Dogde Ram Sport, 3"lift 33" tires. Current system: Alpine 9885 RF power 6.5 coax (only off deck) RF P2 12 in 1ft^3 sealed center console Eclipse xa 1000 (sub amp) The plan: Alpine 9885 RF power 6.5 PG Tantrum 400.4 Mach 5 audio Mj 18 M 4dvc 6 ft^3 tuned to 32-35 hz (Hvae heard blowthoughs lower tuning?) PG Tantrum 1200.1 She listens to mostly R&B and Rap so I think this should make her happy for the time being. I'll upload pics as I can Weather and work will determine how quickly this gets done. as always I am open to any suggestions or comments. Thanks Chad

Here is my build log. I have a 2008 Jeep Grand Cherokee with two SSA ZCON 12’s. I have the subs, amps and batteries in and just working on getting the electrical and speakers installed. Running low on funds but here is what I have so far.

This build is in a 2006 Nissan Xterra. I am currently upgrading a few things, so figured I start a build log. The equipment list at this point. Headunit: Pioneer AVH-X4800bs DSP: Alpine PXA-H800 w/RUX-C800 controller Amps: Memphis 16-MCA3004 on tweeters Alpine MRP-F600 for mids Alpine MRP-M2000 on sub duty Current drivers: Tweeters: SSA Evils Mid: Seas U18/RNX/P Subs: SSA Icon 15"s sealed Batterys: Super Start Platium 34/78PLT (front) Super Start Platium 48PLT (rear) Here's the pics!

Figured I would post this here too as I'm using a couple SSA vendor products. Bringing it back for the sealed guys. Might be a while to get this one finished up but hoping I can get it done in decent time. Going with 4 AA Havoc 15's in a sealed 10 cubic foot Fisher Customs box. Hopefully Chris or BJ can chime in with a sketchup of the box. Power will be from an American Bass 500.1 running at .5ohm. Electrical I am adding 3 powermaster d3100's, a second positive run of 1/0 and two negative 1/0 runs. Already have one run of positive, a yellowtop, and a 200amp meangreen alt installed. Frontstage (already installed) is some boston pro's on a kicker zx550.2 in sealed/damped/o…

whats up guys? i been doing some upgrades to my electric the past few weeks and i think im about done (for the time being haha) here is what i have done for the new build so far..... HU: sony xplode (the nice one lol) speakers: stock but that is my next step Amp: 1 aq2200 running .5ohm (only until i can afford a 2nd 2200 and strap them) Subs: 2 12" ssa zcons (NEW!) Electric: 250amp alt. ( Thanks!),1 optima red top under the hood and 2 deka 9a31's in the back, all 0 gauge and big 3 is done. i will be posting all the new updates to the system here! eyecandy..... Truck: New Alt. Subs: a new box is in the near future...

Here is the low on my setup. I have a 2001 Chevy blazer 4x4 Headunit-CDA-105 Electrical- DB Electrical 220 amp alt, 2 C&D 100ah batts 4channel- Audiopipe 2004 Front stage- CDT Com 626 and CDT 6.5 Coaxails Sub amp- Audiopipe 3k Subs- 4 RD audio Sonance v2 12s dual 4 TSUNAMI 1/0 LOTS OF FATMAT EXTREME Here we go ill start off fast the box will be being rebuilt unless I find a good deal on a couple 15s. My car Stock alt with TSUNAMI 1/0 DB Electrical 220amp alt C&D batteries Headunit Now for some fatmat HIghs amp CDT Crossover and Tweet in B pillars CDT Mid Sub amp and subs Im deading the rest of the doors and finishing my comps today ill post more pic…

I'm started a new build for my 2007 chevy avalanche. the box will be 25 cft. 9 cft per sub with 400" port area tunned to 37 hz. I'm using 9518g subs pushed by a hifonics xxv sampson with 8 kinetiks hc1800 batteries. I provided a link i have too many pics to post here.please give me any feed back.I still have alot of work left .this is just the start. http://s948.photobucket.com/albums/ad328/cmcveigh74/

This is my first build log, please lower any expectations of competency... The system- Raxiom (rebadged Rosen unit) HU- got it because it integrate perfectly with the factory media and had NAV. Zed Audio Mikro 4 channel Rockford Fosgate T500 bd JBL Power Series 6 1/2" components in the front front (no speakers go in the doors (I take them off as often as possible)) Bravox 5 1/4" components in the sound bar (custom made mounting ring, CLD tiles to help the flimsy plastic) SSA XCON 10" in a ported box designed by the SSA store and built with the help of my buddy. It's my (and his) first speaker box built.

my boy codys tahoe i built with his help and a few team members.. couple mechman 270s subs dyed the carpet shell complete

Right of the bat I can tell you this will take a while since its been going on for a while. The wife already said no so now it has to happen. The couch is ready and the fridge is full. Here is a teaser pic. More to follow soon. Belly of the beast

Trying to figure out how to posts pics again !!! I don't know if my computer is too slow or my files too big. I made a photobucket account today, but I don't see how to post pics from there. I am studying it ! Until I can post some pics !!! Sorry

1996 Cavalier 2 door Cuirrently: 1 - Kenwood X994 Head Unit 1 - 18" Soundstream XXX 2 - Audioque AQ3500D.1 1 - Audioque 4x90 1 - Set Alpine Type R 6 1/2 components 2 - Optima Yellow Tops 1 - 155 amp Alternator Still to come: 2 - 220 amp alts 2 - XS Power D3100 batteries Sexy amps! Nice! Test fitting the baffle with sub mounted: Horrible safety mask! lol Grinding down and re-using the molded glass bottom of the prior box for this build. Trying to get as much box volume as possible while still keeping everything in the trunk! Pocket holes ftw! More test fitting Ports, front and back sides flared. Messy! Not so messy! Base of the box Start of more glass work.…

I'm in the process of rebuilding my system and figured why not post a few pics. Any reasonable suggestions would be most appreciated. my system will be installed in my P.O.S. 02 cavalier and will consist of 1-An audiocontrol eqx 1- set hertz hsk 165 comps 1 pair of 10" peerless sls (for midbass) 3- rockford fosgate 25th anniversary punch 150's and a pair of Custom SSA Icon 15's(awaiting recones at the momment.) So far I have made some mounting brackets for the hertz mids and my amp rack. more pics and updates will follow but I don't have alot of time to work on my car so finishing this will be slow going. Here is how I made my brackets. The green marks the angle…

A few months ago I deadened the floor pan and the rear wall with a roll of RAAMmat and it cleaned up the sound tremendously. I have a Massive Audio CW12 downfiring out of a JL Audio Stealthbox disguised as the middle seat. Then I decided that new speakers were in order because the JL Audio TR series were not doing a good enough job. I did some research and decided on Focal Polyglass speakers and the new Focal Solid 2 channel amplifier. Considering the 6.5 inch woofer and the 4 inch mid wouldn't fit in the stock 6x9 hole I had to make baffles and glass them into the doors. Right now its just a temporary solution until I figure out a better way to do it. This is not show qu…

This is my new baby. I've only had it for about a month now. Its a 1974 Dodge Charger. My problem. It only has an AM radio. That a previous owner rudely cut the wires extremely short on. So I've set out to build my own small enclosure to put in an After market DIN receiver under my dash. Not wanting to harm the original hardware any of course. Many more pictures to come. Of all parts of install. Any of your guys' thoughts or opinions would be greatly appreciated!! thanks!!

Hey guys manzkea back at it again! Lol. Finally got some equipment in. Excited to finally get this project I’ve had in mind for a while rolling . Gonna attempt a blow through in my single cab 2001 ford ranger long bed. Gonna make pods for the doors to house the 6.5s and replace the stock one with a 6.5 or if possible an 8” driver. All powered off the ssa ic150.4. As for subs I’ll be using a 15” sp4 v2 I got from a friend for a deal. A taramps 5k will be used to push it. Unfortunately the evil mids I wanted was unavailable in 4ohms. So I went with these prvs. Well I’ll I’ll be updating this as I get it going. Possibly next week or so, really busy with wor…

I think its a Chevy... Anyway, Joel has done a fair bit of customizing on this unit and will continue to do so through this winter. As the first pic shows he has removed the door handles, replacing them with an electronic system that ties into his Viper car alarm. He also did some front and back end frame work. This picture does the truck paint job no justice whatsoever - you would have to see it live to appreciate it The next shot shows the interior with the back seat ripped out. He will also be ripping out his single 12" Diamond Audio sub, replacing it with two SPL-15's. The cap will also go, but the nice Audison 1kw amp stays to power the front stage The next s…

I just got this installed last Monday, i believe the 13th, so anyway i have a 12bl fully loaded, sundown sae 1200d, should of got the 1500d, and all 0 gauge wire. I also have the box ported and built to specs. The only thing i need to do is carpet the box. I have all 0 gauge wire. My lights dim badley. I upgraded just the grpund wire in my hood with 0 guage and it stoped the dimming and could let me listen more. Just 1 problem.... How come when im listening to songs with really loud bass like beamer benz or bentley my system stops hitting for 3 seconds and then continues to hit, but if my volume is down it doesent stop.. Why is that? OHH by the way people think i have 4 s…

I'm copying this from ***.. Well I guess I'll post up here too. Here's the 'daily'. 2005 Blazer. 4.3 V6 Automatic. A/C 4x4. Its got about 60,000kms on it. My dad and I started on this box. I had wenn_du_weinst design this for me. Its tuned to 35hz, I can't remember if he told me the airspace. Day one looked like this. Knocked a little piece out.. Lookin down the port. Bottom of the box.. Day two I glued the second baffle on, and cut out the sub holes. This is the second time I've used a jig saw, first time was yesterday when I cut out a mount for y CB out of some left over mdf. I think the holes turned out okay? Its all glued inside on the seams. This is what …

This is in my cousins '96 Buick Regal. Thanks to Vertex Audio for the equipment 2 15" IA LI (should arrive any day now) 1 run Shok industries 1/0 1 American Pro VS-1598 Here are some more pics and specs on the amp since it's not a popular amp/brand VS-1598 500rms x 2 @ 2ohms The box is 7ft net tuned to 36hz with 96sq of port. First cut, 1 side of the port Since my table saw was stolen we were using this one- damn it's so nice to use Marking the port 3/4 round over on the port. Trying out the new "jawhorse" thing. It works pretty nice! Also with the small router- really good for laminate and easier to control with my home made base than the large router …

Been putting this off for a while. I have been contemplating on doing a wall then I said nah i'll just trade the sub and back to keeping it and doing something with it. Well here goes a buncha wasted time later and I finally decided to kick off the build. I decided to stay street and try something different for once. I will reveal my complete box plans once it is in the car. Time for pics.

Do you have a blazer or s10 pick-up? Post your pics! Here are some of mine. Any questions go ahead and ask.

Well this is the first transmission line box i've ever built.. I read the tutorial yesterday on how to build one and didn't think it was that hard, so i built this one this morning in my spare time. Took about 2 hours to cut and assemble the box.. After getting it done i put it in a chevy s-10 blazer, with some kind of off brand amp pushing only about 300-400 (sad but that's all he had. Haha..). And with that little power running to it, everything flexes in his truck, and it's loud from 25hz all the way up to 60hz.. I'm very impressed with t-line boxes, and i find them easier to build than just regular ported box.. Haha.. Specs: Fs of a D1 Fi Bl is 35.2 Box "port" is exac…