Build Logs

The box is not finished yet, sorry not more pictures of the build to busy, but i still have to router the port the top and paint it, and I may even cut an inch of the box out somewhere bc it is a little to tall but we will see. Amps should be where wednesday I hope, and with them i still have to run power and ground to the back and get another battery and a new atternater but atternater will probably be the last thing i buy. Thats all for now but it's in and pounding

ok..im suppose to be studying but im doing this instead. just thougt id share my build. its the second box i built and the first install ive done...consists of everything in my sig...here we go...

Here are some final pictures for a build I did for a customer. Box is 8.4 cubes @ 35hz for 2 HDC3 15's. Box is not being covered with anything. customer will do what he pleases. Gonna be fun to ship... Enjoy

When I started planning on this project 2 years ago, in the planning stages, I wanted 60+ and to bassrace 59.9, but since then I have taken it down a notch, wanting to build something that plays low ( Fla style), Loud and moves an absolute insane amount of air. What I started with Subs 8 DC Level 5 M1 Motors, with David from PSi working his magic on the rest. 8 18" recones 3 spider setup Amps - 4 SK2500.1s from Skar audio. The setup got down pretty good with these, but I needed more power, and less problems a single 300A Tenney that has yet to fail me A 4th order bandpass All Wiring and accessories were acquired from Audio Technix. over 100ft of OFC 1…

Ok this is for a buddy of mine i think he has an account on here, I can't remember though. It is 1 15" Audioque hdc3 aluminum coil on a Sundown saz 3k at 2 ohm, (might talk him into half an ohm at comps lol). As of now he does not have a front stage to brag about, but I'm going to get him hooked up one way or another. He has a pioneer headunit, don't remember what model. Will have big 3 done and a xs power d3400 in the back. (going to also upgrading stock battery, which luckily is already located in the back. And alredy has couple coats of dampner. Box is 4.1 cubes @ 36hz Ok on with the pics. Still have to throw 2 more coats of clear and carpet it, then bui…

Just follow the pics and you can figure it out.

Here goes to the start of deadening my 02 Z71. Lots of deadening going in. 155 Sq ft. Raammat 5 or 6 Yards Ensolite 5 gallons and 1 quart of Spectrum GM's way of trying to stop you from removing the rear bolts on the front seats an 11mm 12 point did the trick. Also the front nuts on the front seat are removable with 15mm 12 point. Carpet is not so clean lol When I saw this clip for the first time I thought "I'll come at you like a spider monkey!" The rear light needs to be removed before dropping the headliner to disconnect the light More pics to come

I haven't posted in a while but I sold my orange truck and got a 2004 cadillac escalade. The plan is 2 sp4 18's on 7,000 to 10,000 watts. So far I have my aq 2200 on my btl 15. Scared and I are building a box in the next week or two.

Well, well, well, Look what the cat dragged in. super surreal to be back on the forum after pretty much a friggin decade. it’s nice to see most of y’all are still active here! Here’s the current build in the works for my 2005 forester. Plan/currently installed: -6.5 door upgrades (2 evil 6.5 up front paired to some evil tweets|2 coaxial alpine typeS in rear doors. Most likely going to make custom crossovers for the front) -1 Sundown Sax100.4 -Sound deadening on the inner door skins removed all plastic lining on door skins aswell. -old ass pioneer Bluetooth double din head unit from 2012 On the way to me: -1 SSA Evil 15” woof…

box is 2.6 or 2.8 @ 34hz going in 06 altima on ap1500 @ .5 Uploaded with ImageShack.us Uploaded with ImageShack.us Uploaded with ImageShack.us Uploaded with ImageShack.us Uploaded with ImageShack.us Uploaded with ImageShack.us Uploaded with ImageShack.us

ok since i cant cut outside at my place to work on nicks car ive been goin over to my team leaders house from work and working on his install of all the stuff he has bought off me over the past few months. i won a pair of square brutus 12s and a brutus 1200w amp at the maxxonics show and i sold him the package and told him i would do his install for him. Equipment HU- Pioneer 7800mp Subs - Hifonics Brutus 12s Sub Amp - Hifionics Brutus 1200w amp Mids/Highs - Memphis M class 6.5" coaxials (2 pair) Mids/Highs Amp - JL Audio 300/4 RCA's/Power Wire - Knukonceptz Extra Battery - Kinetik HC2400 been working on it for 4 nights now about 3 hours a night from like 3am till 6am.…

i have a 1995 s10 blazer and i plan on ordering a 18 and maybe doing a second one anybody out there have or know if i can get 2 18s in a blazer non wall and not removing back seats.also i would like to see pics of your setups blazer only i wanna get an idea of how im gonna do my setup

I noticed I never posted this here and thought some here who don't visit the other site may enjoy it. It's and old school RF build in my wifes Camry. She wanted all old school RF equipment because she liked the look of them when I used them in her first car in the early to mid 90s. I couldn't argue because I like their performance. I chose IB on the subs to keep as much trunk for her as possible. The only piece that isn't old school is the 3sixty. I couldn't see using a symmetry unit over the 3sixty. Symmetry was only a little less than getting the 3sixty and the 3sixty has way more flexibility. Equipment.

It has been far too long since I have had a vehicle that I could do a build in, so I'm super excited to be working on this. The pieces that you can't see are the SS Damp and Overkill in the doors. Equipment as of right now consists of DLS components up front running active off a Sundown SAX 100.4, 2 SoundSplinter Orphan8's powered by a Zapco Ref 750.2, with an Eclipse CD8443 for a head unit. Wiring is from Knu with 1/0 for power and ground, 4 gauge distro'd to the amps, 12 gauge for speaker wire. I'll be replacing the Zapco with a Sundown 1500D when I save up a little more, since the Zapco is my brother's and he's just loaning it to me at the moment. I stabbed a hole i…

This is my first sub box. I've done some other carpentry stuff before but have always been too scared to try and build a sub box in fear it would sound like chit and be a total waste of effort. It's 2 cubes tuned at 41hz. I'm trying to get more spl out of my sub on 500 watts to give me an edge in the basic 1 class in my local circuit. I hit 135.5db on my current setup but that may not get er done. I could have finished much sooner if I had more clamps. I'll glue the top down tonight after I find my tie down straps and do the pseudo-in law family Easter gig. I almost forgot to add the part about my girlfriend's wisdom teeth being taken out Friday. Puffy puffy cheeks.

Decided against the underseat box since i have very little experience. Once im more confident in doing bevels and cutting angles i think ill do it. Any way i lost one seat and gained mad bass, ill take that trade off lol. heres the woofer Beefy 12" Shot at 2011-07-12 Shot at 2011-07-12 Heres the box Shot at 2011-07-12 Shot at 2011-07-12 Shot at 2011-07-12 Shot at 2011-07-12 A little weight for the baffle Shot at 2011-07-12 Shot at 2011-07-12 Dont have a razor, so i improvised for the carpeting Shot at 2011-07-12 here it is installed, hopefully i can get a vid of it flexing my truck i just need to find a better camera than my cell phone. Shot at 2011-07-12

Hello everyone I would like to start by saying I have no intention of breaking or bending any site or community rules here so pls forgive me if I do that is not my intention. I am here to share my personal experience with cherrymancustoms who has built me an extremely personalized and truly custom enclosure to meet the needs of my particular listening goals. This man has spent literally countless hours over-the-phone speaking with me one on one in an attempt to maximize my enclosure design and has built what I consider to be a very good quality box. I have attached images for your own viewing and judgement below. His website is www.cherrymancustoms.com/ where he ha…

I just finished up with my install: 2) 12" D2 GCONS in a DC-Creations Sealed Enclosure, all installed in a 2012 Volkswagen GLI running from the factory fender audio system to a LC2i LOC and Kicker ZX1000.1 Amp w/ KnuKonceptz Kolossus Flex 0 ga kit. GCONS: Visually: I placed my order and received the speakers about 25-30 days later, just like the guys @ SSA said. Between the heavy foam surround, to the huge magnet, to the frame, they look SICK. Looks wise, I can't complain, the build quality seems to be great; real heavy duty shit here. When I bought my kicker amp from the car audio shop around the block, the guy I dealt with asked what I was running for subs. So I show…

The Pioneer AVH-P4200 installed: Positive and Negative upgrades on the battery: The positive upgrade from alternator: Close up of the new positive terminal: Close up of the new negative terminal: The Second Skin Damplifier Pro. I bought way too much: The SSA Icon 12"!: Tools used to remove panels to add the sound damplifier (the mallet was to break a pin holding the airbag panel on the c-pillar): The sound damplifier added on. It was a pain in the ass because of all of the holes for the rear deck clips and stuff. I had to cut small pieces and put them all over and started to get lazy with it and missed some spots because of it. I was so worn out from spending so m…

well figured i might as well post a build log on what ive been putting together. just a few pics to get started post some later of the box and what not. 2 15" Memphis CM MOJOs(have) or 2 15" PSI custom reconed MOJO M3s(ordered) Sundown SAZ-3500D v.2(have) DC Power 270XP(have) 1 XS Power D5100R(have) 2 XS Power XP3000(ordered) 2 runs weldingsupply 2/0AWG (have) enclosure designed by PWK(built) update: box and subs are in running off the saz-3500v2 @ 4ohm til i get batts and wire. keeping Memphis MClass mids/highs will upgrade in the near future

Hey guys, whats up. Well I will be uploading my current build of not only my car audio, build, but performance, paint and body work, and upgrades. Car audio build as follows: Headunit: pioneer p5200bt Speakers: Selenium 6.5 mids (8) Sub: AA SMD 15" d1 Amps: Sundown 3500, and two JL 300/2 Batteries: XS Power D3400, (Currently waiting for new XP 3000's) Alt: DC POWER XP 270 (Ordered January 10th, still hasn't arrived) Will be uploading vids, and pics of doors, sub, unboxing etc

Not done yet

Well.....I've switched over to (2) 10'' SSA ICONS sealed from a 10'' Fi BL in 1.25ft^3@33hz. I couldn't get enough port area for a decent ported box so I was forced to ditch the BL. Here's a list of the equipment: Powermaster xs1200 Kicker Hyperflex 1/0 Pioneer Premier Ts-c720 w/ Seas tweets Sundown 100.2 (2) 10'' ICONS in 1.4ft^3 sealed JL 1000/1

The dude wanted something different, doesnt care anything about sq really, and definately doesnt care much about spl. He just wanted it to be loud and look good doing it. Hes going to be running an orion 2500d. We hooked it up to mine tonight just after we got done and are going to have to use alot of althread, this thing flexx's like a mother. But it did turn out looking good! Just for you guys info, its an 18"

Well figured I had better make a build log for this. I have 40ft^2 of Second Skin Damplifier coming tomorrow and I'm buying another 40ft^2 and 18ft^2 of SS Luxury Liner. I also got my comps in the day before. Rainbow Profi line 5.25" set. I went with the 5.25's b/c I want to keep the truck looking as stock as possible. I'm still debating on were to put my tweeters and the crossovers though. I'm open to any suggestions... I'll have lots of pictures through out the whole process. It will probably take me a good week plus to do it all b/c its my only vehicle and I need it for work so I will have to work small area's at a time. I'm hoping to deaden the crap out of the…