Sound Solutions Audio (SSA®)

better video than the first but still not that great. Put it up on youtube this time. Sub is wired to 1 ohm and gets dumb loud off of the ed nine.1 but you cant really tell in the video. When i get a good video camera ill take some quality shots but for now this will have to do. Still havent fixed the screws... ill do that today though. enjoy

How much would it cost to recone an ssa icon 15"???? thanks in advance

Some backstory about me..... OK, I've been into audio for a few years. I always ran what the locals consider inferior or off brand subs. There's just something great about running paper cone house subs (adire audio shivas) and beating everyone in town in the spl comps I wanted to improve on my previous score of 148.7 on the dash using 2 shivas. (The meter was a terrasonde xmeter that I suspect measures about 6-8 db higher than a TL) I ran 2 S15L7's for about a year and only hit a 150.5 on that same meter. I was still the loudest person in town, but I know in the spectrum of spl comps, that setup was a joke. I decided to build a wall that summer. Well, after some tr…

I was just wanting to know how long it usually takes to have them manufactured and shiped out

Looking for a little help on deciding which sub setup to run. First off the vehicle is a 2005 explorer. Already have a Sundown SAZ-3500d to power them. Electrical upgrades will be DC 270 amp alt., big three in 1/0, two runs to back of vehicle in 1/0 and 2 D3100 batteries. Purpose of the system is daily ground pounder. Want loud and clean. Listen to a little bit of everything except country. The original plan was 2 XCON 15's in a ported enclosure. I've been reading the forum a lot and watched some videos and have seen some really nice systems using 12" XCONS and ICONS. My uncle suggested I run four 12" ICONS sealed. He has always run sealed enclosures. My dads b…

Just a quicky video I made. I just noticed that when it shows me turning up the bass knob it appears to be at full, when in fact it's only half, the knob spun out one day becuase of the heat down here so the dot doesn't line up to where it's actually at lols. Anyways, here's the video...

So I drove to Sumter today and met up with Master Yoda for the test and tune. This was my first try on any meter and I really had no idea what to expect. I was kinda worried I might get over there and embarrass myself being a virgin and all. Here are the results 148.55 @ 36hz sealed legal 146.10 @ 40hz Average on music 148.67 @ 36hz Peak music I am always pretty conservative with my gains and noticed zero clipping on the TL meter and also got some suggestions to help improve on this. Yoda is putting this on again in 2 weeks and I am curious to see what I can do with a little tweaking and maybe a little turn of the gain. Not too bad for a first time rookie running SQ sub…

I'm looking at purchasing either an Xcon or a Zcon. The Xcon is listed as having an aluminum shorting ring in the motor. My question is whether the Zcon does or not? I am assuming that it does not have an inductance demodulation circuit in the motor since it is not listed under the features. Can anyone confirm this please? Thanks.

Has anyone purchased or done an install with a 10" xcon? If so can you post your feedback or info.

I just received my DCON(phenomenal driver) last week and be playing it for about 3 days now. Just wondering what's the recommended break in time for it.

Hi guys, After lots of research I decided I'd really like to get the Icon 12. I'm most likely putting this in a prefabbed box so I need to make sure it will fit. Does anybody have the magnet diameter for this sub? I see the mounting depth but not the magnet diameter listed on the product page. Thanks!

i see that the free xcon enclosures have an optimum ported, but no dual optimum ported. regular ported is 2.6 cubic feet, what would be the optimum ported enclosure for 2 xcon tens?

does anyone know if the icon will preform well in a 3 cu ft. ported box? 3 cubes is all i can fit in my CRX since i want to keep the sub covered. any input would be great

So I don't have the programs required to design a superb box, so I was hoping for some help, even if it requires some sort of payment, because it seems like an intense build to me. I am going with 2 18 inch XCONs and will use a SAZ-3500d. It will be the toughest build I have done due to the size and I want it to turn out great because I have decided to use a theme. I have been deciding on subs and amps forever it seems, so I said why not just represent the forum that has helped me through all of my indecisiveness and taught me so much (tears lol). I want to paint it in a color scheme to match my school colors, so red and white, probably with the emblem on one side, an…

So, a friend of mine is looking for some good bass in his car. He has tried many things, and I don't think he is looking in the right place. He currently has 2 12 Kenwood KFCs in a sealed box, but has also had pioneer 10s, (the gray ones from wal-mart), and visonik 10s and 12s. The problem with the Kenwoods is that they don't hit the lows he is looking for. I was hoping to help him sell the Kenwoods and was thinking of steering him towards the DCONS, (budgeted install... budget is probably what he can get for the kenwoods and 1 10inch pioneer and his amp, a sony 220 gtx). I think that he wants to be plenty loud, but still sound good on a low budget. The vehicle is a…

Finnaly pulled the trigger and ordered a mighty XCON!! I love what you guys are doing and I can't freakin wait to get my Xcon!! The sense of community is really one of the many things I really like most about you guys and I love supporting the smaller business. (Especially when they have the capability to kick the arse of most of those mainstream companies!) Been out of the game for a while and it really wasn't like this last time I had a system. I was so close to getting JL its not even funny. Thats before I stumbled onto the SSA forums and the rest as they say is history. I've learned a lot from you guys on all of the different SSA froums and I truly appreciate it!!…

I would like to know the status on these recones I ordered back on may 2nd. I talked to Mark when we were at Big Apple for a comp this past sunday and he told me to get ahold of him and he would see what was going on, but I am unable to get ahold of him.. Any and all help with would be great!! thanks

I just want to express my gratitude and tell you guys at SSA that the new site is fvcking amazing looking and is MUCH more user friendly than the last, somewhat "confusing to navigate" site (especially for viewing threads and posting). I'm on CA most of the day, but this site appearance dogs CA's.

Check them out here: http://store.soundsolutionsaudio.com/products/f8l-8-sound-solutions-audio-8-650w-f8l-series-subwoofer.html

Any idea yet what power handling will be on these?

Just a couple snaps of the Lancer from the Herr Foods Inc. Cruise night held in Nottingham PA. I didn't bother with pictures of all the glam rods or anything like that, just a couple of the car and the unfinished install.

This may sound strange, but I was wondering what would be involved with getting more details on the actual dimensions of the ZCON and XCON 15" Basically like the magnet diameter, thickness of it, etc. (an actual technical drawing would be great too!) Reason I ask is I am working on a design for my friend's car and have enough cubic feet but limited height to work with, so I'm trying to see if I can make one of these fit. I want him to be an SSA guy if possible! Thanks in advance!

I am looking for a redone kit for my old 2009 icon 12. Any idea where I can find one. Also I would like to send it in to where I buy from insuring it is done professionally.

Which one would you guys go with? The pioneer flip out or kenwood flipout? I've used the kenwood, and may buy today. Need opinions on how fast compared they are. Features don't matter, only backup cam and variation of eq setting.

Will the Icon 15 be offered in D2's again?? thx