Jump to content
Sign in to follow this  
cloud77

Fi BL 15" D1 Fully Loaded

Recommended Posts

*Fi Car Audio*

Fi BL 15" Dual 1 ohm coils

-Flatwound coil

-Cooling

-Hyper pole

-Integrated leads

-daily gap

-Universal gap

In great shape, only used it in between my builds a couple times. Been sitting in my living room most of its existence.

300 shipped. US 48. Paypal only.

2014-06-21_14-56-19_183.jpg

2014-06-21_14-55-35_791.jpg

2014-06-21_14-51-50_776.jpg

2014-06-21_14-47-08_413.jpg

2014-06-21_14-46-51_484.jpg

2014-06-21_14-46-34_522.jpg

2014-02-08_13-57-45_920-1.jpg

2014-02-08_13-57-02_892.jpg

Share this post


Link to post
Share on other sites

250 shipped today!  I'm on 4 sites with this listed price.  First to send $$$ owns it

Share this post


Link to post
Share on other sites
Sign in to follow this  

  • Similar Content

    • By ManzKea
      Hey guys manzkea back at it again! Lol. Finally got some equipment in. Excited to finally get this project I’ve had in mind for a while rolling . Gonna attempt a blow through in my single cab 2001 ford ranger long bed. Gonna make pods for the doors to house the 6.5s and replace the stock one with a 6.5 or if possible an 8” driver. All powered off the ssa ic150.4.  As for subs I’ll be using a 15” sp4 v2 I got from a friend for a deal. A taramps 5k will be used to push it.
      Unfortunately the evil mids I wanted was unavailable in 4ohms. So I went with these prvs.
       
      Well I’ll I’ll be updating this as I get it going. Possibly next week or so, really busy with work at the moment. Well here’s a pic of some goodies the mail man dropped off.  Cheee. 
       
       Btw got something extra special in those two ssa looking boxes behind the ranger gear. But that’s on the back burner at the moment. 

    • By jcarter1885
      Slow build, but wanted to get a build log going.




    • By mikebingham34
      Hello all, I have been away from the forums for some time since graduating college and started working again. Now that I have some money to finally move away from these seemingly low powered setups (6 systems since 2012), I am looking for help with my wall build. I am going to be building the base to the wall in my 2016 Ford Focus sedan in a week or two, and there is a lot of room to work with (over 30 cubes). I will be running 2 18" ZCONs on (undecided) either a 5.5k or 6.5k amp with supporting electrical (batt bank, lots of OFC wire, and HO alt). This is my daily, and I just want a ground pounder with no care to what numbers it'll put up in the lanes. I would like to demo a lot. I'm thinking 8 cubes per sub (16 cubes net) tuned to 32 Hz is a good place to start (recommended by SSA). I'm thinking either a center slot port, or a top port.
      ** I listen to ALL kinds of music, Decaf/DJSNT, rap, hip hop, metal, rock, 80s/90s pop, jazz, country, movie scores, blues, dubstep/electronic, classic rock, oldies, etc, etc..**
      Now... my questions are: How much port area do y'all recommend? Is 8 cubes of net volume per sub a good amount? Should I be alright running an underrated 5500 watt amp, or go with the 6500? What port orientation shall I go with? 
      If I think of more questions, I will be sure to post them. 
      P.S. Sorry if I am asking some questions that are common knowledge among these builds, but this is my first "loud" and "high powered" setup. My two loudest systems thus far have been a single Obsidian Audio 15 on about 900 watts, and 2 Sundown Ev3-12's on 1300 watts.
      Thank you for your time and patients everyone! Cheers.
  • Who's Online   1 Member, 0 Anonymous, 26 Guests (See full list)

  • Recently Browsing

    No registered users viewing this page.

×