haha found some T/S for the jackhammer

[PaulD 0]

I think it was only meant to be a wow factor display

[CBFryman 2]

Wow...not all too different.

Electrical Q Value -Qes: 0.68

Mechanical Q Value -Qms: 2.82

Total Speaker Q Value -Qts: 0.55

Free Air Resonance -Fs: 15.60 Hz

Equivalent Compliance -Vas: 482 liters

One-Way, Linear Excursion -Xmax: 54 mm

Efficiency - SPL 1W/1m: 86.20 dB SPL

Effective Piston Area -Sd: 1210 cm^2

DC Resistance -Re: 4.2 ohm

Nominal Impedance -Znom: Dual 2 ohm

Thermal Power Handling -Pe: 2000 W

Force Factor -Bl: 18.16

ROTFLMAO

[007 0]

Tell me that is that NOT the new $2300 RE 18" XXX???

[Adrian_D 520]

i believe it is.

i was taliking to the only Re importer over here, and he said he's going to have the xxx18 available for 1250$ . i think he wanted to say at least double that price.

the '06 xxx18 retails for 2300$ ?

EDIT : lol, same bl^2/re as my rl-i 10.

Edited July 29, 2006 by Adrian_D

[007 0]

Wow

Based on those measurements, the 12 and 15" XXX should be good contenders for the current RL-s. The motor force and sensitivity is about the same and both have linear(ish) motors.

Edited July 29, 2006 by 7

[iagrdshaka 0]

I would rather have SoundSplinter anyway. No one likes a sell-out.

[CBFryman 2]

Tell me that is that NOT the new $2300 RE 18" XXX???

<{POST_SNAPBACK}>

you are correct.

looking at that XXX 18 = crap. Jackhammer's little brother.

All the little n00bx's do is see Xmax as being 54mm and they call it some bad ass mofo.

Ive yet to see video or pictures or feed back of an install where the XXX was moving anywhere near full potential. A guy on CSO was running 4kW to one and two SE 12's where still louder with a LOT less power.

When I first saw it Ithought "nifty, 5" P2P." After it came out and i saw the price, looked at the specs, and then waited for the results of what people had to say I laughed. RE is a joke to me now.

Ive seen videos of the MX series moving further than the XXX with a lot less power. Not that you can judge output strictly by movement in anything but a sealed and IB alignement. However isnt that why RE made these? lots of linear displacement?

RE =

/

[mrray13 30]

motion to name the jackhammer as a turd...

Loyd L.

seconded.....

do we have a third?

when we do, we'll wwrite mtx a letter, see if we can't get one sent to loyd for , umm, testing, tell them to put up, or shut up...muhahahahahahah

ryan, post your thoughts you chickenshit....

kyle, new re xxx vs rl-s? hmmmm......considering you can buy almost three rl-s' for the reduced price of the xxx, seems almost pointless considering the performance of the rl-s...why even consider the xxx when there is .....wait, nevermind...because it's a bandwagon thing. if it doesn't say xxx somewhere, it can't be good.

wheeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee

[007 0]

I see you got my exact point.

[Aaron Clinton 2,372]

I see you got my exact point.

Mark me down for the third and final vote for turd.

[///M5 2,833]

I see you got my exact point.

Mark me down for the third and final vote for turd.

You beat me by a couple of hours